Study of using micro‐nano bubble to improve workability and durability of self‐compact concrete

2021 ◽  
Author(s):  
Behnaz Yahyaei ◽  
Gholamreza Asadollahfardi ◽  
Amir Masoud Salehi
Keyword(s):  
Self Compact Concrete

scholarly journals Fresh, Mechanical Properties and Impact Resistance Behavior of Eco-Friend Self-Compacted Concrete

2019 ◽  
Vol 22 (3) ◽  
pp. 208-212
Author(s):  
Sheelan M. Hama ◽  
Alhareth M. Abdulghafor ◽  
Mohammed Tarrad Nawar
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Glass Powder ◽  
Impact Resistance ◽  
Waste Glass ◽  
Slump Flow ◽  
Waste Glass Powder ◽  
Self Compact Concrete

In this work, waste glass powder from broken windows and plastic fibers from waste polyethylene terephthalate bottles are utilized to produce an economical self-compact concrete. Fresh properties (slump flow diameter, slump Flow T50, V. Funnel, L–Box), mechanical properties (Compressive strength and Flexural strength) and impact resistance of self-compact concrete are investigated. 15% waste glass powder as a partial replacement of cement with five percentages of polyethylene terephthalate plastic waste were adopted: 0% (reference), 0.5%, 0.75%, 1%, 1.25% and 1.5% by volume. It seems that the flow ability of self-compact concrete decreases with the increasing of the amount of plastic fibers. The compressive strength was increased slightly with plastic fiber content up to (0.75%), about 4.6% For more than (0.75%) plastic fiber. The compressive strength began to decrease about 15.2%. The results showed an improvement in flexural strength and an impact on the resistance in all tested specimens’ content of the plastic fibers, especially at (1.5%) fibers.

Experimental studies on flexural behaviour of self compact concrete beam

2020 ◽  
Vol 33 ◽  
pp. 129-135 ◽  
Author(s):  
K Perumal ◽  
A Kumar ◽  
N Lingeshwaran ◽  
Sambaraju Susmitha
Keyword(s):  
Concrete Beam ◽  
Experimental Studies ◽  
Flexural Behaviour ◽  
Self Compact Concrete

scholarly journals USING CARBON FIBER STRIPS IN JOINTS STRENGTHING OF BOX SEGMENTAL SELF-COMPACTING CONCRETE BEAMS

2020 ◽  
Vol 24 (06) ◽  
pp. 22-32
Author(s):  
Ahmed H. Hashim ◽  
◽  
Waleed A. Wrayosh ◽  
Keyword(s):  
Carbon Fibers ◽  
Concrete Beams ◽  
Precast Concrete ◽  
Reference Beam ◽  
Concrete Surface ◽  
Self Compacting Concrete ◽  
Cfrp Sheets ◽  
Mode Of Failure ◽  
Cracking Mode ◽  
Self Compact Concrete

The main objective of this research is to study the effect of carbon fibers used to strengthen the joints of the box segmental beams. For this research, four beams were produced and tested. One of these beams, monolithically, was cast as a reference beam and the three others were segmental beams. All beams were produced with Self-Compact Concrete (SCC) and box cross section. Each segmental beam consisted of three precast concrete segments were connected by post tensioning tendons. The three segmental beams have same characteristics, but different in joint types between the segments. The types of joints used were (dried , epoxied and dried strengthen by CFRP sheets). All beams were tested under static two point loads up to failure. For each test, deflections at mid-span location were recorded for each (5kN). Also, first cracking, mode of failure and ultimate loads values were recorded as well as the concrete surface strains at the specified locations for both loadings.

scholarly journals Partial Replacement of Fine Aggregate with Foundry Sand in Self Compacted Concrete

2021 ◽  
Vol 9 (VI) ◽  
pp. 2802-2807
Author(s):  
Mohd Abdul Rehman
Keyword(s):  
Ferrous Metal ◽  
Silica Sand ◽  
Metal Casting ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Self Compacting Concrete ◽  
Natural Sand ◽  
Foundry Sand ◽  
Casting Industry ◽  
Self Compact Concrete

This document demonstrates the possibility of using foundry sand waste as a partial replacement of sand in self-compact concrete. Self-compacting concrete, as the name implies, is a type of concrete that does not require an external or internal seal because it is aligned and consolidated under its weight. Foundry sand is a high-quality silica sand that is used as a molding material for the ferrous and non-ferrous metal casting industry. It can be reused in foundries, but after a certain period it cannot be used further and becomes waste, called waste, used or used foundry sand (WFS, UFS or SFS). This experimental study was conducted to assess the strength and strength of SCC properties in which natural sand was partially replaced by foundry sand waste (WFS). Natural sand was replaced by four percent (0%, 10%, 15%, 20%, 30% and 40%) WFS by weight.

Sign in / Sign up

Export Citation Format

Share Document