Continuous Measurement of Atomic Force Microscope Tip Wear by Contact Resonance Force Microscopy

Small ◽  
2011 ◽  
Vol 7 (8) ◽  
pp. 1018-1022 ◽  
Author(s):  
Jason P. Killgore ◽  
Roy H. Geiss ◽  
Donna C. Hurley
Keyword(s):  
Atomic Force Microscope ◽  
Continuous Measurement ◽  
Force Microscopy ◽  
Atomic Force ◽  
Contact Resonance

Stick-to-sliding transition in contact-resonance atomic force microscopy

2018 ◽  
Vol 113 (8) ◽  
pp. 083102
Author(s):  
C. Ma ◽  
V. Pfahl ◽  
Z. Wang ◽  
Y. Chen ◽  
J. Chu ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Force Microscopy ◽  
Atomic Force ◽  
Contact Resonance

Plate geometries for contact resonance atomic force microscopy: Modeling, optimization, and verification

2018 ◽  
Vol 124 (1) ◽  
pp. 014503 ◽  
Author(s):  
Matteo Aureli ◽  
Syed N. Ahsan ◽  
Rafiul H. Shihab ◽  
Ryan C. Tung
Keyword(s):  
Atomic Force Microscopy ◽  
Force Microscopy ◽  
Atomic Force ◽  
Contact Resonance

Sensor Egregium – An Atomic Force Microscope Sensor for Continuously Variable Resonance Amplification

2021 ◽  
pp. 1-23
Author(s):  
Rafiul Shihab ◽  
Tasmirul Jalil ◽  
Burak Gulsacan ◽  
Matteo Aureli ◽  
Ryan Tung
Keyword(s):  
Finite Element Analysis ◽  
Atomic Force Microscope ◽  
Natural Frequencies ◽  
Proof Of Concept ◽  
Element Analysis ◽  
Force Microscopy ◽  
Atomic Force ◽  
Wide Range ◽  
Curve Veering ◽  
Dynamic Phenomena

Abstract Numerous nanometrology techniques concerned with probing a wide range of frequency dependent properties would benefit from a cantilevered sensor with tunable natural frequencies. In this work, we propose a method to arbitrarily tune the stiffness and natural frequencies of a microplate sensor for atomic force microscope applications, thereby allowing resonance amplification at a broad range of frequencies. This method is predicated on the principle of curvature-based stiffening. A macroscale experiment is conducted to verify the feasibility of the method. Next, a microscale finite element analysis is conducted on a proof-of-concept device. We show that both the stiffness and various natural frequencies of the device can be highly controlled through applied transverse curvature. Dynamic phenomena encountered in the method, such as eigenvalue curve veering, are discussed and methods are presented to accommodate these phenomena. We believe that this study will facilitate the development of future curvature-based microscale sensors for atomic force microscopy applications.

scholarly journals Scanning speed phenomenon in contact-resonance atomic force microscopy

2018 ◽  
Vol 9 ◽  
pp. 945-952 ◽  
Author(s):  
Christopher C Glover ◽  
Jason P Killgore ◽  
Ryan C Tung
Keyword(s):  
Atomic Force Microscopy ◽  
Hydrodynamic Theory ◽  
Squeeze Film ◽  
Resonance Spectroscopy ◽  
Related Phenomenon ◽  
Contact Mode ◽  
Force Microscopy ◽  
Atomic Force ◽  
Scan Speed ◽  
Contact Resonance

This work presents data confirming the existence of a scan speed related phenomenon in contact-mode atomic force microscopy (AFM). Specifically, contact-resonance spectroscopy is used to interrogate this phenomenon. Above a critical scan speed, a monotonic decrease in the recorded contact-resonance frequency is observed with increasing scan speed. Proper characterization and understanding of this phenomenon is necessary to conduct accurate quantitative imaging using contact-resonance AFM, and other contact-mode AFM techniques, at higher scan speeds. A squeeze film hydrodynamic theory is proposed to explain this phenomenon, and model predictions are compared against the experimental data.

Atomic force microscopy of slip lines in FeAl

1995 ◽  
Vol 10 (9) ◽  
pp. 2159-2161 ◽  
Author(s):  
J.H. Schneibel ◽  
L. Martínez
Keyword(s):  
Atomic Force Microscopy ◽  
Atomic Force Microscope ◽  
Room Temperature ◽  
Frequency Distributions ◽  
Slip Lines ◽  
Force Microscopy ◽  
Atomic Force ◽  
Shear Strains

Fe–40 at. % Al–0.1 at. % B specimens were polished flat, strained at room temperature, and examined in an atomic force microscope. The angles of height contours perpendicular to the slip lines were interpreted as shear strains and were statistically evaluated. The frequency distributions of these shear strains correlated well with the macroscopic strains. The maximum shear strains found were not much larger than the macroscopic strains. In particular, no steep slip steps corresponding to large local shears were found.

Sign in / Sign up

Export Citation Format

Share Document