Fabrication and Characterization of Type‐II Heterostructure n:In 2 O 3 /p:in‐TiO 2 for Enhanced Photocatalytic Activity

2020 ◽  
pp. 2000441
Author(s):  
Sinitha B. Nair ◽  
K. Aijo John ◽  
Julie Ann Joseph ◽  
Shinto Babu ◽  
V. K. Shinoj ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Type Ii ◽  
Fabrication And Characterization

scholarly journals Fabrication and Characterization of an InAs(Sb)/In x Ga 1− x As y Sb 1− y Type‐II Superlattice

2019 ◽  
Vol 13 (12) ◽  
pp. 1970045
Author(s):  
Peng Du ◽  
Xuan Fang ◽  
Qian Gong ◽  
Jiaming Li ◽  
Xufeng Kou ◽  
...  
Keyword(s):  
Type Ii ◽  
Type Ii Superlattice ◽  
Fabrication And Characterization

Fabrication and characterization of TiO2/short MWNTs with enhanced photocatalytic activity

2007 ◽  
Vol 61 (11-12) ◽  
pp. 2467-2472 ◽  
Author(s):  
Yongsong Luo ◽  
Jinping Liu ◽  
Xiaohong Xia ◽  
Xiaoqin Li ◽  
Tao Fang ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Fabrication And Characterization

Fabrication and Characterization of Photocatalyst Coatings by Heat Treatment in Carbon Powder for TiC Coatings

2017 ◽  
Vol 263 ◽  
pp. 137-141
Author(s):  
Su Jun Guan ◽  
Liang Hao ◽  
Hiroyuki Yoshida ◽  
Hiroshi Asanuma ◽  
Fu Sheng Pan ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Oxygen Vacancies ◽  
Treatment Temperature ◽  
Carbon Powder ◽  
Treatment Conditions ◽  
Fabrication And Characterization ◽  
Mechanical Coating

Photocatalyst coatings on alumina (Al2O3) balls had been successfully fabricated by mechanical coating technique, with titanium carbide (TiC) powder and subsequent heat treatment in carbon powder. The effect of heat treatment conditions in carbon powder on the formed compounds, surface morphology and photocatalytic activity of photocatalyst coatings was investigated. XRD results show that the formed compounds change with increasing the heat treatment temperature in carbon powder, and rutile TiO2 on the surface of TiC coatings at 1073 K and 1173 K. The generated oxygen vacancies confirmed by XPS measurement, are in favor of narrowing band gap to enhance the visible-light photocatalytic activity of photocatalyst coatings. The photocatalytic activity of photocatalyst coatings has been effectively enhanced, and the samples fabricated at 1073 K and 1173 K for 2 h show higher activity. The fabrication strategy provides us a facile preparation procedure of visible-light responsive photocatalyst coatings.

Fabrication and characterization of CdS doped TiO2 nanotube composite and its photocatalytic activity for the degradation of methyl orange

2015 ◽  
Vol 72 (8) ◽  
pp. 1341-1347
Author(s):  
Jinwook Chung ◽  
Seu-Run Kim ◽  
Jong-Oh Kim
Keyword(s):  
Photocatalytic Activity ◽  
Methyl Orange ◽  
Uv Light ◽  
Pure Tio2 ◽  
Tio2 Nanotube ◽  
Doped Tio2 ◽  
Photodegradation Efficiency ◽  
Uv Light Irradiation ◽  
Fabrication And Characterization

CdS doped TiO2 nanotube composite was fabricated by chemical bath deposition, and was characterized by the structural, spectral and photoelectrochemical properties. The results of the structural and spectral properties showed that CdS particles were successfully deposited onto the surface of TiO2 nanotube. It is demonstrated that CdS doped TiO2 nanotube composite improved the light harvesting ability. Power conversion efficiency of about 0.32% was observed. This value is about 2.9 times higher than that of pure TiO2 nanotube. The CdS doped TiO2 nanotube composite possesses relatively higher photocatalytic activity and photodegradation efficiency than that of pure TiO2 nanotube under UV light irradiation, and the degradation efficiency of methyl orange was about 42% at UV intensity of 32 W.

Sign in / Sign up

Export Citation Format

Share Document