scholarly journals Structural, optical, and mechanical properties of cobalt copper oxide coatings synthesized from low concentrations of sol-gel process

2016 ◽  
Vol 213 (12) ◽  
pp. 3205-3213 ◽  
Author(s):  
Amun Amri ◽  
Zhong-Tao Jiang ◽  
Chun-Yang Yin ◽  
Ahmad Fadli ◽  
Mohammad Mahbubur Rahman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Copper Oxide ◽  
Sol Gel ◽  
Oxide Coatings ◽  
Low Concentrations ◽  
Sol Gel Process ◽  
Optical And Mechanical Properties ◽  
Cobalt Copper

Preparation and Mechanical Properties of BiFeO3 Ceramics

2016 ◽  
Vol 697 ◽  
pp. 293-296
Author(s):  
Xiao Yang Zhang ◽  
Xi Wei Qi ◽  
Zhi Yuan Yang ◽  
Li Bao ◽  
Min Zhang
Keyword(s):  
Mechanical Properties ◽  
Hydrothermal Method ◽  
Perovskite Phase ◽  
Sol Gel ◽  
Cold Isostatic Pressing ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Three Point Bending ◽  
Multiferroic Bifeo ◽  
Sol Gel Process

Hydrothermal method and sol-gel process were used to synthesize multiferroic BiFeO3 ceramics. X-ray diffraction, scanning electron microscopy, vickers diamond indenter and three-point bending method were used to investigate the effects of methods on the phase structure, microstructures and mechanical properties. Cold isostatic pressing on the ceramics with two different loads (10 MPa, 200 MPa) was used to illustrate the influence of pressure in mechanical properties. The results show that all samples are crystallized in the perovskite phase. A few small traces of impurity are observed at a 2θ of ~28 o, which are found to be those of Bi2Fe4O9. The SEM images depict that samples prepared by sol-gel process are more uniform and the grain size is slightly larger than that of hydrothermal processed samples. The investigations on the hardness and flexural strength demonstrate the ceramics prepared by hydrothermal method have better mechanical properties than that of sol-gel process, and the mechanical properties can be obviously enhanced by increasing pressure.

scholarly journals Tuning the structure and the mechanical properties of epoxy–silica sol–gel hybrid materials

RSC Advances ◽  
2016 ◽  
Vol 6 (13) ◽  
pp. 10736-10742 ◽  
Author(s):  
Berta Domènech ◽  
Ignasi Mata ◽  
Elies Molins
Keyword(s):  
Mechanical Properties ◽  
Porous Material ◽  
Hybrid Materials ◽  
Sol Gel ◽  
Silica Sol ◽  
One Pot ◽  
Sol Gel Process

A new epoxy–silica porous material prepared via one-pot sol–gel process. Mechanical properties can be continuously tuned by modifying reactant proportions.

Preparation and Properties of PVC-Silica Composites using Different Catalysts Via Sol-Gel Process

1999 ◽  
Vol 576 ◽  
Author(s):  
Khan M. Asif ◽  
M.I. Sarwar ◽  
Z. Ahmad
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Sol Gel ◽  
Silica Network ◽  
Transparent Films ◽  
Sol Gel Process ◽  
Gel Technique ◽  
In Situ Generation ◽  
Scanning Electron

Novel micro-composites from Polyvinyl chloride (PVC) and silica were prepared using sol-gel technique. Different catalysts were used for the in-situ generation of silica network from tetraethylorthosilicate (TEOS) in the PVC matrix. Thin transparent films containing various proportions of silica in PVC were cast by the solvent elution technique. Mechanical properties of these films were studied. The results showed an increase in the value of Young's modulus and strain at rupture by the addition of small amount of silica in PVC. However, the stress at yields point and stress at rupture decreased with the addition of silica contents. Scanning electron microscopy (SEM-EDAX) studies were also performed on these samples.

Sign in / Sign up

Export Citation Format

Share Document