High-efficiency silicon solar cells: Full factor limitations and non-ideal diode behaviour due to voltage-dependent rear surface recombination velocity

1993 ◽  
Vol 1 (2) ◽  
pp. 133-143 ◽  
Author(s):  
Armin G. Aberle ◽  
Stephen J. Robinson ◽  
Aihua Wang ◽  
Jianhua Zhao ◽  
Stuart R. Wenham ◽  
...  
Keyword(s):  
Solar Cells ◽  
High Efficiency ◽  
Rear Surface ◽  
Surface Recombination ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Voltage Dependent ◽  
Ideal Diode ◽  
Recombination Velocity ◽  
Rear Surface Recombination

scholarly journals Numerical Simulation Analysis of Ag Crystallite Effects on Interface of Front Metal and Silicon in the PERC Solar Cell

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 592
Author(s):  
Myeong Sang Jeong ◽  
Yonghwan Lee ◽  
Ka-Hyun Kim ◽  
Sungjin Choi ◽  
Min Gu Kang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Surface Recombination ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Metal Interface ◽  
Ag Crystallites ◽  
Recombination Velocity

In the fabrication of crystalline silicon solar cells, the contact properties between the front metal electrode and silicon are one of the most important parameters for achieving high-efficiency, as it is an integral element in the formation of solar cell electrodes. This entails an increase in the surface recombination velocity and a drop in the open-circuit voltage of the solar cell; hence, controlling the recombination velocity at the metal-silicon interface becomes a critical factor in the process. In this study, the distribution of Ag crystallites formed on the silicon-metal interface, the surface recombination velocity in the silicon-metal interface and the resulting changes in the performance of the Passivated Emitter and Rear Contact (PERC) solar cells were analyzed by controlling the firing temperature. The Ag crystallite distribution gradually increased corresponding to a firing temperature increase from 850 ∘C to 950 ∘C. The surface recombination velocity at the silicon-metal interface increased from 353 to 599 cm/s and the open-circuit voltage of the PERC solar cell decreased from 659.7 to 647 mV. Technology Computer-Aided Design (TCAD) simulation was used for detailed analysis on the effect of the surface recombination velocity at the silicon-metal interface on the PERC solar cell performance. Simulations showed that the increase in the distribution of Ag crystallites and surface recombination velocity at the silicon-metal interface played an important role in the decrease of open-circuit voltage of the PERC solar cell at temperatures of 850–900 ∘C, whereas the damage caused by the emitter over fire was determined as the main cause of the voltage drop at 950 ∘C. These results are expected to serve as a steppingstone for further research on improvement in the silicon-metal interface properties of silicon-based solar cells and investigation on high-efficiency solar cells.

The Effect of Al-BSF on Seff and Rb in Industrialized Mono-Silicon Solar Cells

2012 ◽  
Vol 472-475 ◽  
pp. 1846-1850
Author(s):  
Shan Shan Dai ◽  
Gao Jie Zhang ◽  
Xiang Dong Luo ◽  
Jing Xiao Wang ◽  
Wen Jun Chen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Rear Surface ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Back Surface

In this work, the effect of aluminum back surface field formed by screen printed various amount of Al paste on the effective rear surface recombination velocity (Seff) and the internal rear reflectance coeffeicient (Rb) of commercial mono-silicon solar cells was investigated. We demonstrated the effect of Seffand Rbon the performance of Al-BSF solar cells by simulating them with PC1D. The simulated results showed that the lower Seffcould get higher open circuit voltage (Voc), at the same time, the larger Rbcould get higher short-circuit current (Isc). Experimentally, we investigated the Seffand Rbthrough depositing Al paste with various amount (3.7, 5, 6, and 8 mg/cm2) for fabricating Al-BSF mono-silicon solar cells. Four group cells were characterized by light I-V, spectral response, hemispherical reflectance and scanning electron microscope (SEM) measurements. It was found that, a minimum Seffof 350 cm/s was gotten from the cells with Al paste of 8 mg/cm2, which was extracted by matching quantum efficiency (QE) from 800 nm to 1200 nm with PC1D, and a maximum Rbof 53.5% was obtained from Al paste of 5 mg/cm2by calculating at 1105 nm with PC1D. When the amount of Al paste was higher than 5mg/cm2, there were less Seffand lower Rb. On the other hand, when Al amount was 3.7mg/cm2, it was too little to form a closed BSF. Based on the SEM graphs and simulations with PC1D, a simple explaination was proposed for the experimental results.

Low effective back‐surface recombination velocity by boron implantation on 0.3‐Ω‐cmp‐type silicon solar cells

1988 ◽  
Vol 63 (9) ◽  
pp. 4683-4687 ◽  
Author(s):  
Leendert A. Verhoef ◽  
Albert Zondervan ◽  
Fredrik A. Lindholm ◽  
Mark B. Spitzer ◽  
Christopher J. Keavney
Keyword(s):  
Solar Cells ◽  
Surface Recombination ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Back Surface ◽  
Type Silicon ◽  
Boron Implantation ◽  
Recombination Velocity
Sign in / Sign up

Export Citation Format

Share Document