scholarly journals Nanocomposites based on low density polyethylene filled with carbon nanotubes prepared by high energy ball milling and their potential antibacterial activity

2019 ◽  
Vol 68 (6) ◽  
pp. 1155-1163 ◽  
Author(s):  
Erika Benigno ◽  
Miguel A Lorente ◽  
Dania Olmos ◽  
Gustavo González‐Gaitano ◽  
Javier González‐Benito
Keyword(s):  
Carbon Nanotubes ◽  
Antibacterial Activity ◽  
Ball Milling ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Energy Ball

An Investigation on the Mechanical Alloying of TiFe Compound by High-Energy Ball Milling

2010 ◽  
Vol 660-661 ◽  
pp. 329-334 ◽  
Author(s):  
Railson Bolsoni Falcão ◽  
Edgar Djalma Campos Carneiro Dammann ◽  
Cláudio José da Rocha ◽  
Ricardo Mendes Leal Neto
Keyword(s):  
Ball Milling ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Powder Mixtures ◽  
Milling Parameters ◽  
Process Route ◽  
Partial Formation ◽  
Energy Ball

This work reports the efforts to obtain TiFe intermetallic compound by high-energy ball milling of Ti and Fe powder mixtures. This process route has been used to provide a better hydrogen intake in this compound. Milling was carried out in a SPEX mill at different times. Strong adherence of material at the vial walls was seen to be the main problem at milling times higher than 1 hour. Attempts to solve this problem were accomplished by adding different process control agents, like ethanol, stearic acid, low density polyethylene, benzene and cyclohexane at variable quantities and keeping constant other milling parameters like ball to powder ration and balls size. Better results were attained with benzene and cyclohexane, but with partial formation of TiFe compound even after a heat treatment (annealing) of the milled samples.

Research the Al Material Reinforced by CNT(Carbon Nanotubes)

2011 ◽  
Vol 694 ◽  
pp. 337-340
Author(s):  
Xiao Lan Cai ◽  
Xiao Fei Wang
Keyword(s):  
Carbon Nanotubes ◽  
Ball Milling ◽  
Rotational Speed ◽  
Milling Time ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Compound Material ◽  
Energy Ball ◽  
Rotary Speed ◽  
Xrd Patterns

This paper using high energy ball milling(HEM), researched the technology of preparation of Al compound material reinforced by CNT. Researched the different milling time, rotary speed, amount of CNT and sinter technology on properties of hardness and density. Preparation the Al-CNT at milling time about 30 to 100 min, rotational speed is about 300-600/rpm.the wt% of CNT is 0-5%, Analyzed the XRD patterns、SEM and STM micrograph, the results showed the Al material could be reinforced by CNT using HEM. the hardness of Al-CNT is 75 HB and the density is 2.65 g/cm3 when milling 90 min and CNT 3%.

Synthesis, Characterization, and ECAP Consolidation of Carbon Nanotube Reinforced AA 4032 Nanocrystalline Composites Produced by High Energy Ball Milling

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
M. S. Senthil Saravanan ◽  
S. P. Kumaresh Babu
Keyword(s):  
Carbon Nanotubes ◽  
Crystallite Size ◽  
Ball Milling ◽  
Base Alloy ◽  
Arc Discharge ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Nanocrystalline Powders ◽  
Peak Broadening ◽  
Energy Ball

In the present work, multiwalled carbon nanotubes (MWNTs) were synthesized by electric arc discharge method in open air atmosphere. The synthesized nanotubes were subjected to multistep purification followed by characterization using Raman spectroscopy and transmission electron microscopy (TEM). These carbon nanotubes (CNTs) have inner and outer diameters of the order of 3.5 nm and 16 nm with an aspect ratio of 63. AA 4032 nanocomposites reinforced with MWNTs were produced by high energy ball milling using elemental powder mixtures. X-ray diffraction (XRD) and scanning electron microscope (SEM) studies showed different phases of composite with and without CNTs. The crystallite size and lattice strain were calculated using an anisotropic model of Williamson–Hall peak broadening analysis, which showed in decreased crystallite size with increasing milling time. TEM studies reveal that the MWNTs were uniformly distributed in the matrix. Thermal stability of the nanocrystalline powders was studied using a differential thermal analyzer (DTA). The mechanically alloyed powders were consolidated using a novel method called equal channel angular pressing (ECAP) at room temperature. The consolidated samples were sintered at 480 °C in argon atmosphere for 90 min. ECAP method was investigated as an alternative to conventionally sintered powder composites. CNT addition has shown significant improvement in the hardness of the system, even though the observed density is relatively low compared with a base alloy. Thus, the results show that ECAP enables sufficient shear deformation results in good metallurgical bonds between particles at lower compaction pressures. Hence, it is proven that ECAP can be effectively used as one of the consolidation technique especially for powders that are difficult to consolidate by other means.

Incorporation of carbon nanotubes into polyethylene by high energy ball milling: Morphology and physical properties

2007 ◽  
Vol 45 (5) ◽  
pp. 597-606 ◽  
Author(s):  
Giuliana Gorrasi ◽  
Maria Sarno ◽  
Antonio Di Bartolomeo ◽  
Diana Sannino ◽  
Paolo Ciambelli ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Physical Properties ◽  
Ball Milling ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Energy Ball
Sign in / Sign up

Export Citation Format

Share Document