Improved models of viscosity and relaxation modulus for epoxy resin during cure

2016 ◽  
Vol 56 (6) ◽  
pp. 617-621 ◽  
Author(s):  
Huimin Li ◽  
Boming Zhang
Keyword(s):  
Epoxy Resin ◽  
Relaxation Modulus

Effect of Cure State on Stress Relaxation in 3501-6 Epoxy Resin

1997 ◽  
Vol 119 (3) ◽  
pp. 262-265 ◽  
Author(s):  
S. R. White ◽  
A. B. Hartman
Keyword(s):  
Stress Relaxation ◽  
Epoxy Resin ◽  
Creep Compliance ◽  
Numerical Technique ◽  
Matrix Material ◽  
Relaxation Modulus ◽  
Master Curves ◽  
Creep Tests ◽  
Three Point Bending ◽  
Direct Inversion

Little experimental work has been done to characterize how the viscoelastic properties of composite material matrix resins develop during cure. In this paper, the results of a series of creep tests carried out on 3501–6 epoxy resin, a common epoxy matrix material for graphite/epoxy composites, at several different cure states is reported. Beam specimens were isothermally cured at increasing cure temperatures to obtain a range of degrees of cure from 0.66 to 0.99. These specimens were then tested in three-point bending to obtain creep compliance over a wide temperature range. The master curves and shift functions for each degree of cure case were obtained by time-temperature superposition. A numerical technique and direct inversion were used to calculate the stress relaxation modulus master curves from the creep compliance master curves. Direct inversion was shown to be adequate for fully cured specimens, however it underpredicts the relaxation modulus and the transition for partially cured specimens. Correlations with experimental stress relaxation data from Kim and White (1996) showed that reasonably accurate results can be obtained by creep testing followed by numerical conversion using the Hopkins-Hamming method.

Viscoelastic Properties of an Epoxy Resin during Cure

2001 ◽  
Vol 35 (10) ◽  
pp. 883-904 ◽  
Author(s):  
Daniel J. O'Brien ◽  
Patrick T. Mather ◽  
Scott R. White
Keyword(s):  
Epoxy Resin ◽  
Viscoelastic Properties ◽  
Entire Range ◽  
Parallel Plate ◽  
Relaxation Modulus ◽  
Material Behavior ◽  
Gel Point ◽  
Processing Conditions ◽  
Practical Model ◽  
Point Bend

The cure dependent relaxation modulus of an epoxy resin was investigated over the entire range of cure extent. Parallel plate rheometry was used to measure the material behavior below the gel point of the epoxy network. Creep testing in three-point bend was used for specimens cured past gelation. All data were converted to the stress relaxation modulus for comparison of the material behavior among the various cure states and between the two experimental techniques. The data were used to develop a practical model for predicting the cure dependence of the relaxation modulus throughout cure under varying processing conditions.

Ultrastructural investigation of spontaneous pituitary gonadotroph cell adenomas in aging Sprague-Dawley rats

1983 ◽  
Vol 41 ◽  
pp. 702-703
Author(s):  
D. J. McComb ◽  
J. Beri ◽  
F. Zak ◽  
K. Kovacs
Keyword(s):  
Electron Microscopy ◽  
Animal Model ◽  
Epoxy Resin ◽  
Immunoelectron Microscopy ◽  
Tumor Type ◽  
Gonadal Function ◽  
Sprague Dawley ◽  
Male And Female ◽  
Reticulin Fibers ◽  
Sprague Dawley Rats

Gonadotroph cell adenomas of the pituitary are infrequent in human patients and are not invariably associated with altered gonadal function. To date, no animal model of this tumor type exists. Herein, we describe spontaneous gonadotroph cell adenomas in old male and female Sprague-Dawley rats by histology, immunocytology and electron microscopy.The material consisted of the pituitaries of 27 male and 38 female Sprague Dawley rats, all 26 months of age or older, removed at routine autopsy. Sections of formal in-fixed, paraffin-embedded tissue were stained with hematoxylin-phloxine-saffron (HPS), the PAS method and the Gordon-Sweet technique for the demonstration of reticulin fibers. For immunostaining, sections were exposed to anti-rat β-LH, anti-ratβ-TSH, anti-rat PRL, anti-rat GH and anti-rat ACTH 1-39. For electron microscopy, tissue was fixed in 2.5% glutaraldehyde, postfixed in 1% OsO4 and embedded in epoxy-resin. Tissue fixed in 10% formalin, embedded in epoxy resin without osmification, was used for immunoelectron microscopy.

Surface Structure in Microtomed Sections Caused by Glass and Diamond Knives

1971 ◽  
Vol 29 ◽  
pp. 456-457
Author(s):  
J. Temple Black ◽  
William G. Boldosser
Keyword(s):  
Plastic Deformation ◽  
Epoxy Resin ◽  
Carbon Coating ◽  
Surface Damage ◽  
Body Angle ◽  
Normal Manner ◽  
Bottom Side ◽  
Cutting Direction ◽  
Made In ◽  
Diamond Knife

Ultramicrotomy produces plastic deformation in the surfaces of microtomed TEM specimens which can not generally be observed unless special preparations are made. In this study, a typical biological composite of tissue (infundibular thoracic attachment) infiltrated in the normal manner with an embedding epoxy resin (Epon 812 in a 60/40 mixture) was microtomed with glass and diamond knives, both with 45 degree body angle. Sectioning was done in Portor Blum Mt-2 and Mt-1 microtomes. Sections were collected on formvar coated grids so that both the top side and the bottom side of the sections could be examined. Sections were then placed in a vacuum evaporator and self-shadowed with carbon. Some were chromium shadowed at a 30 degree angle. The sections were then examined in a Phillips 300 TEM at 60kv.Carbon coating (C) or carbon coating with chrom shadowing (C-Ch) makes in effect, single stage replicas of the surfaces of the sections and thus allows the damage in the surfaces to be observable in the TEM. Figure 1 (see key to figures) shows the bottom side of a diamond knife section, carbon self-shadowed and chrom shadowed perpendicular to the cutting direction. Very fine knife marks and surface damage can be observed.

Epoxy Resin Embedment

1968 ◽  
Vol 26 ◽  
pp. 100-101
Author(s):  
J. G. Adams ◽  
M. M. Campbell ◽  
H. Thomas ◽  
J. J. Ghldonl
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
Epoxy Resin ◽  
Light Microscope ◽  
Epoxy Resins ◽  
Image Contrast ◽  
Tissue Preservation ◽  
Resin System ◽  
Excellent Quality

Since the introduction of epoxy resins as embedding material for electron microscopy, the list of new formulations and variations of widely accepted mixtures has grown rapidly. Described here is a resin system utilizing Maraglas 655, Dow D.E.R. 732, DDSA, and BDMA, which is a variation of the mixtures of Lockwood and Erlandson. In the development of the mixture, the Maraglas and the Dow resins were tested in 3 different volumetric proportions, 6:4, 7:3, and 8:2. Cutting qualities and characteristics of stability in the electron beam and image contrast were evaluated for these epoxy mixtures with anhydride (DDSA) to epoxy ratios of 0.4, 0.55, and 0.7. Each mixture was polymerized overnight at 60°C with 2% and 3% BDMA.Although the differences among the test resins were slight in terms of cutting ease, general tissue preservation, and stability in the beam, the 7:3 Maraglas to D.E.R. 732 ratio at an anhydride to epoxy ratio of 0.55 polymerized with 3% BDMA proved to be most consistent. The resulting plastic is relatively hard and somewhat brittle which necessitates trimming and facing the block slowly and cautiously to avoid chipping. Sections up to about 2 microns in thickness can be cut and stained with any of several light microscope stains and excellent quality light photomicrographs can be taken of such sections (Fig. 1).

The Application of Ultra-Thin Sectioning Techniques to Non-Biological Samples

1968 ◽  
Vol 26 ◽  
pp. 332-333
Author(s):  
C. F. Oster
Keyword(s):  
Biological Sciences ◽  
Epoxy Resin ◽  
Cross Sections ◽  
Biological Samples ◽  
Industrial Applications ◽  
Photographic Film ◽  
Silver Particles ◽  
Thin Sectioning ◽  
Embedding Medium

Although ultra-thin sectioning techniques are widely used in the biological sciences, their applications are somewhat less popular but very useful in industrial applications. This presentation will review several specific applications where ultra-thin sectioning techniques have proven invaluable.The preparation of samples for sectioning usually involves embedding in an epoxy resin. Araldite 6005 Resin and Hardener are mixed so that the hardness of the embedding medium matches that of the sample to reduce any distortion of the sample during the sectioning process. No dehydration series are needed to prepare our usual samples for embedding, but some types require hardening and staining steps. The embedded samples are sectioned with either a prototype of a Porter-Blum Microtome or an LKB Ultrotome III. Both instruments are equipped with diamond knives.In the study of photographic film, the distribution of the developed silver particles through the layer is important to the image tone and/or scattering power. Also, the morphology of the developed silver is an important factor, and cross sections will show this structure.

Ultrastructure of the basal body apparatus in epidermal cells of a sponge larva (Aplysilla SP: Demospongiae)

1992 ◽  
Vol 50 (1) ◽  
pp. 928-929
Author(s):  
R.L. Pinto ◽  
R.M. Woollacott
Keyword(s):  
Sodium Bicarbonate ◽  
Epoxy Resin ◽  
Basal Body ◽  
Phosphate Buffer ◽  
Similar Data ◽  
Basal Apparatus ◽  
Striated Rootlet ◽  
The Common ◽  
Basal Foot ◽  
Sexually Mature

The basal body and its associated rootlet are the organelles responsible for anchoring the flagellum or cilium in the cytoplasm. Structurally, the common denominators of the basal apparatus are the basal body, a basal foot from which microtubules or microfilaments emanate, and a striated rootlet. A study of the basal apparatus from cells of the epidermis of a sponge larva was initiated to provide a comparison with similar data on adult sponges.Sexually mature colonies of Aplysillasp were collected from Keehi Lagoon Marina, Honolulu, Hawaii. Larvae were fixed in 2.5% glutaraldehyde and 0.14 M NaCl in 0.2 M Millonig’s phosphate buffer (pH 7.4). Specimens were postfixed in 1% OsO4 in 1.25% sodium bicarbonate (pH 7.2) and embedded in epoxy resin. The larva ofAplysilla sp was previously described (as Dendrilla cactus) based on live observations and SEM by Woollacott and Hadfield.

ACOUSTIC PROPAGATION IN AN EPOXY RESIN AT VERY LOW TEMPERATURES

1982 ◽  
Vol 43 (C9) ◽  
pp. C9-509-C9-511
Author(s):  
P. Doussineau ◽  
W. Schön
Keyword(s):  
Epoxy Resin ◽  
Low Temperatures ◽  
Acoustic Propagation
Sign in / Sign up

Export Citation Format

Share Document