Properties and performance of a simulated consumer polymer waste-coal combustion byproduct composite material

2013 ◽  
Vol 54 (6) ◽  
pp. 1239-1247 ◽  
Author(s):  
Herman Potgieter ◽  
Christopher Liauw ◽  
David Velado
Keyword(s):  
Composite Material ◽  
Coal Combustion ◽  
Polymer Waste ◽  
And Performance ◽  
Waste Coal

Study on the technology and performance of 3D-reticulated porous SiC/Fe composite material

2018 ◽  
Vol 26 (3) ◽  
pp. 247-262 ◽  
Author(s):  
Qingming Chang ◽  
Liang Chen ◽  
Jie Zhang ◽  
Yawei Li ◽  
Xiong Liang
Keyword(s):  
Composite Material ◽  
And Performance ◽  
Porous Sic

A thermodynamics-guided framework to design lightweight aggregate from waste coal combustion fly ash

2022 ◽  
Vol 178 ◽  
pp. 106050
Author(s):  
Mohammad Balapour ◽  
Thiha Thway ◽  
Rathin Rao ◽  
Newell Moser ◽  
Edward J. Garboczi ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Combustion ◽  
Lightweight Aggregate ◽  
Waste Coal

Heat-Insulating Composite Material Based on Wood and Polymer Waste

2020 ◽  
Vol 24 (2) ◽  
pp. 28-33 ◽  
Author(s):  
A.S. Kolosova ◽  
E.S. Pikalov ◽  
O.G. Selivanov
Keyword(s):  
Composite Material ◽  
Methylene Chloride ◽  
Experimental Studies ◽  
Raw Material ◽  
Insulation Material ◽  
Pressing Pressure ◽  
Regulatory Requirements ◽  
Deciduous Species ◽  
Waste Products ◽  
Polymer Waste

The results of the development of a raw mixture, which contains a filler obtained by grinding a mixture of small-sized wood waste based on light dirt varieties of coniferous and deciduous species, and a binder obtained by dissolving the waste products from polystyrene foam in methylene chloride, are presented. This mixture allows cold mixing and pressing followed by heat treatment at the boiling point of the solvent. In the course of experimental studies, the influence of the ratio of the mixture components and the pressing pressure on the basic properties and structure of the obtained composite material was established. The composition of the raw material mixture and the pressing were selected to ensure low thermal conductivity in combination with low values of water absorption and swelling density and strength compliant with regulatory requirements. Received thermal insulation material for construction purposes from wood and polymer waste, characterized by large volumes of formation and high rates of accumulation.

The Composite Material from the Recycled Raw Materials in the Purification of Oily Wastewater Technology

2017 ◽  
Vol 736 ◽  
pp. 187-190 ◽  
Author(s):  
E.V. Moskvicheva ◽  
P.A. Sidyakin ◽  
A.V. Moskvicheva ◽  
E.P. Doskina ◽  
D.V. Shchitov ◽  
...  
Keyword(s):  
Composite Material ◽  
Water Treatment ◽  
Environmental Pollution ◽  
Raw Materials ◽  
Oily Wastewater ◽  
Technological Parameters ◽  
Polymer Waste ◽  
Physico Chemical ◽  
Treatment Facilities ◽  
Waste Polymer

Getting a composite of oil and plastic waste and their use as sorbents for cleaning oil drains is considered. The regularity of modifying oil waste polymer waste with polymer waste, physico-chemical and technological parameters are identified. The scheme of modification is worked out. Rational ways to reduce environmental pollution and improve water treatment facilities are found.

Sign in / Sign up

Export Citation Format

Share Document