A super-toughened nylon 12 blends via anionic ring-opening polymerization of lauryllactam in a twin screw extruder. Preparation, morphology, and mechanical properties

2010 ◽  
Vol 50 (6) ◽  
pp. 1178-1185 ◽  
Author(s):  
Libo Du ◽  
Guisheng Yang
Keyword(s):  
Mechanical Properties ◽  
Ring Opening ◽  
Ring Opening Polymerization ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Nylon 12 ◽  
Twin Screw ◽  
Anionic Ring ◽  
Morphology And Mechanical Properties

Study of morphology and mechanical properties of PP/EPDM/clay nanocomposites prepared using twin‐screw extruder and friction stir process

2018 ◽  
Vol 40 (8) ◽  
pp. 3306-3314 ◽  
Author(s):  
Mohammad Reza Nakhaei ◽  
Amir Mostafapour ◽  
Charles Dubois ◽  
Ghasem Naderi ◽  
Mir Hamid Reza Ghoreishy
Keyword(s):  
Mechanical Properties ◽  
Clay Nanocomposites ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Friction Stir Process ◽  
Friction Stir ◽  
Twin Screw ◽  
Morphology And Mechanical Properties

scholarly journals Effects of a Twin-Screw Extruder Equipped with a Molten Resin Reservoir on the Mechanical Properties and Microstructure of Recycled Waste Plastic Polyethylene Pellet Moldings

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1058
Author(s):  
Hikaru Okubo ◽  
Haruka Kaneyasu ◽  
Tetsuya Kimura ◽  
Patchiya Phanthong ◽  
Shigeru Yao
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Value Added ◽  
Industrial Applications ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Polymer Properties ◽  
Wide Range ◽  
Twin Screw ◽  
Recycled Plastics

Each year, increasing amounts of plastic waste are generated, causing environmental pollution and resource loss. Recycling is a solution, but recycled plastics often have inferior mechanical properties to virgin plastics. However, studies have shown that holding polymers in the melt state before extrusion can restore the mechanical properties; thus, we propose a twin-screw extruder with a molten resin reservoir (MSR), a cavity between the screw zone and twin-screw extruder discharge, which retains molten polymer after mixing in the twin-screw zone, thus influencing the polymer properties. Re-extruded recycled polyethylene (RPE) pellets were produced, and the tensile properties and microstructure of virgin polyethylene (PE), unextruded RPE, and re-extruded RPE moldings prepared with and without the MSR were evaluated. Crucially, the elongation at break of the MSR-extruded RPE molding was seven times higher than that of the original RPE molding, and the Young’s modulus of the MSR-extruded RPE molding was comparable to that of the virgin PE molding. Both the MSR-extruded RPE and virgin PE moldings contained similar striped lamellae. Thus, MSR re-extrusion improved the mechanical performance of recycled polymers by optimizing the microstructure. The use of MSRs will facilitate the reuse of waste plastics as value-added materials having a wide range of industrial applications.

Rheology, Morphology and Mechanical Properties of PA6/PP-g-MAH/POE Blends

2011 ◽  
Vol 366 ◽  
pp. 310-313
Author(s):  
Ming Tao Run ◽  
Meng Yao ◽  
Bing Tao Xing ◽  
Wen Zhou
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Screw Extruder ◽  
Reinforcing Agent ◽  
Twin Screw ◽  
Impact Tester ◽  
The Impact ◽  
Plastic Fluids ◽  
Morphology And Mechanical Properties ◽  
Toughening Agent

The rheology, morphology and mechanical properties of the PA6/PP-g-MAH/POE blends prepared by twin-screw extruder were studied by rheometer, scanning electron microscopy, universal tester and impact tester, respectively. The results suggest that the impact strength is improved by the POE acting as a toughening agent, while the compatibility of PA6 and POE is improved by the compatibilizer of PP-g-MAH. Furthermore, the PP-g-MAH component also acts as a reinforcing agent for decreasing the strength depression induced by the POE component. When POE content is about 9 wt% and PP-g-MAH content is about 10% in blends, the blend has the maximum tensile strength and impact strength. All melts of PA6/PP-g-MAH/POE blends are pseudo-plastic fluids. Both the POE and PP-g-MAH components can increase the apparent viscosity of the melt due to their facility of the linear molecular.

Mechanical Properties of Poly(Butylene Succinate) Reinforced with Alpha Cellulose

2015 ◽  
Vol 1119 ◽  
pp. 283-287
Author(s):  
Sarit Liprapan ◽  
Thumnoon Nhujak ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Glycidyl Methacrylate ◽  
Interfacial Interaction ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Butylene Succinate ◽  
Twin Screw

The objective of this study is to prepare α-cellulose reinforced poly (butylene succinate) composites (PBS/α-cellulose). The effect of amount α-cellulose on the mechanical properties of the composites was investigated. To improve interfacial interaction between PBS and α-cellulose, glycidyl methacrylate grafted poly (butylene succinate) (PBS-g-GMA) was used as a compatibilizer. Mechanical properties of PBS composites prepared by using a twin-screw extruder were investigated. The mechanical properties of PBS/α-cellulose decreased due to the agglomeration of α-cellulose. Nevertheless, tensile strength, Young’s modulus and flexural strength of PBS composites were improved after the incorporation of PBS-g-GMA. The optimum loading of PBS-g-GMA and α-cellulose in the PBS was found to be 5 and 6 phr.

Application of a New Twin-Screw Extruder to the Waste Tire Regeneration

2013 ◽  
Vol 561 ◽  
pp. 326-330
Author(s):  
Lei Guo ◽  
Qing Kun Liu ◽  
Chuan Sheng Wang
Keyword(s):  
Mechanical Properties ◽  
Reaction Temperature ◽  
Physical And Mechanical Properties ◽  
Crumb Rubber ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Screw Speed ◽  
Waste Tire ◽  
Twin Screw ◽  
Regeneration Effect

This paper uses a new twin-screw extruder for regeneration of waste tire crumb rubber, discusses the influence of screw speed and reaction temperature on the physical and mechanical properties of reclaimed rubber. Experimental results show that different screw speed and reaction temperature has a great impact on the physical and mechanical properties of the reclaimed rubber. When controls screw speed in the 60 ~ 90 r / min, reaction temperature at 170 to 210°C,the regeneration effect is the best. At this time, the physical and mechanical properties of reclaimed rubber, such as tensile strength, tear strength and elongation at break rate, is the best.

scholarly journals Investigation of the Orientational Mechanical Properties of Biodegradable Extrusion Films Based on Polyolefins and Beet Pulp

2022 ◽  
Author(s):  
A.M. Kuzmin
Keyword(s):  
Mechanical Properties ◽  
Polymer Melt ◽  
Twin Screw Extruder ◽  
Biodegradable Films ◽  
Screw Extruder ◽  
Film Extrusion ◽  
Biodegradable Composites ◽  
Twin Screw ◽  
Beet Pulp ◽  
Extrusion Method

Abstract. The article discusses the possibility of obtaining biodegradable films based on polyolefins and beet pulp by the extrusion method. Biodegradable composites of two mixes with 15% and 25% beet pulp content have been obtained. Compounding was carried out on a twin-screw extruder, and then samples of biodegradable films were obtained by cast film extrusion. The influence of the vegetable filler particles’ orientation on the composites mechanical properties has been studied. It has been shown that composites mechanical properties significantly increase in the direction of polymer melt stretching.

Sign in / Sign up

Export Citation Format

Share Document