Comparative study of single‐layer graphene and single‐walled carbon nanotube‐filled epoxy nanocomposites based on mechanical and thermal properties

2018 ◽  
Vol 40 (S2) ◽  
pp. E1840-E1849 ◽  
Author(s):  
Muhammad Razlan Zakaria ◽  
Muhammad Helmi Abdul Kudus ◽  
Hazizan Md Akil ◽  
Mohd Zharif Mohd Thirmizir ◽  
Muhammad Fadhirul Izwan Abdul Malik ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Carbon Nanotube ◽  
Comparative Study ◽  
Single Layer ◽  
Single Layer Graphene ◽  
Mechanical And Thermal Properties ◽  
Epoxy Nanocomposites ◽  
Single Walled Carbon Nanotube ◽  
Single Walled Carbon ◽  
Layer Graphene

Single Layer Graphene Oxide Sheets-Epoxy Nanocomposites with Greatly Improved Mechanical and Thermal Properties

2011 ◽  
Vol 391-392 ◽  
pp. 175-179 ◽  
Author(s):  
Qing Hong Liu ◽  
Xia Yin Yao ◽  
Zhao Ping Liu
Keyword(s):  
Graphene Oxide ◽  
Thermal Properties ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Single Layer ◽  
Single Layer Graphene ◽  
Mechanical And Thermal Properties ◽  
Mixed Solution ◽  
Epoxy Nanocomposites ◽  
Layer Graphene

The single layer graphene oxide (GO) sheets-epoxy nanocomposites were prepared by directly dispersing concentrated GO aqueous colloid into dimethylformamide (DMF), and then incorporating the mixed solution into epoxy resin. The mechanical and thermal properties of the as-prepared nanocomposites were investigated by Notched Izod impact tests and thermogravimetric analysis. Significant improvements in both impact strength and thermal properties were observed for the nanocomposites at very low level of GO loading content. The impact strength of the nonacomposites containing 0.15 wt% GO was 10.66±0.75 MPa, which was 165.84 % higher than that of the pure epoxy resin (4.01±0.52 MPa). The decomposition temperature of the nanocomposites containing 0.3 wt % GO increased about 12 °C. The effective reinforcement of the GO based epoxy nanocomposites can be attributed to the good dispersion and the strong interfacial interactions between the GO sheets and the epoxy resin matrices.

Temperature-dependent thermal properties of single-walled carbon nanotube thin films

2015 ◽  
Vol 106 (18) ◽  
pp. 183108 ◽  
Author(s):  
A. Duzynska ◽  
A. Taube ◽  
K. P. Korona ◽  
J. Judek ◽  
M. Zdrojek
Keyword(s):  
Thin Films ◽  
Thermal Properties ◽  
Carbon Nanotube ◽  
Temperature Dependent ◽  
Single Walled Carbon Nanotube ◽  
Single Walled Carbon

scholarly journals Thermal Resistance across Interfaces Comprising Dimensionally Mismatched Carbon Nanotube-Graphene Junctions in 3D Carbon Nanomaterials

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Jungkyu Park ◽  
Vikas Prakash
Keyword(s):  
Carbon Nanotube ◽  
Thermal Resistance ◽  
Carbon Nanomaterials ◽  
Single Layer ◽  
Unit Cell ◽  
Single Layer Graphene ◽  
Interfacial Thermal Resistance ◽  
Layer Graphene ◽  
Out Of Plane ◽  
Plane Direction

In the present study, reverse nonequilibrium molecular dynamics is employed to study thermal resistance across interfaces comprising dimensionally mismatched junctions of single layer graphene floors with (6,6) single-walled carbon nanotube (SWCNT) pillars in 3D carbon nanomaterials. Results obtained from unit cell analysis indicate the presence of notable interfacial thermal resistance in the out-of-plane direction (along the longitudinal axis of the SWCNTs) but negligible resistance in the in-plane direction along the graphene floor. The interfacial thermal resistance in the out-of-plane direction is understood to be due to the change in dimensionality as well as phonon spectra mismatch as the phonons propagate from SWCNTs to the graphene sheet and then back again to the SWCNTs. The thermal conductivity of the unit cells was observed to increase nearly linearly with an increase in cell size, that is, pillar height as well as interpillar distance, and approaches a plateau as the pillar height and the interpillar distance approach the critical lengths for ballistic thermal transport in SWCNT and single layer graphene. The results indicate that the thermal transport characteristics of these SWCNT-graphene hybrid structures can be tuned by controlling the SWCNT-graphene junction characteristics as well as the unit cell dimensions.

scholarly journals Carbon nanotube stabilized single layer graphene cantilevers

2017 ◽  
Vol 110 (15) ◽  
pp. 151901 ◽  
Author(s):  
Oleg V. Martynov ◽  
Marc Bockrath
Keyword(s):  
Carbon Nanotube ◽  
Single Layer ◽  
Single Layer Graphene ◽  
Layer Graphene
Sign in / Sign up

Export Citation Format

Share Document