Foam injection molding of glass fiber reinforced polypropylene composites with laminate skins

2017 ◽  
Vol 39 (12) ◽  
pp. 4322-4332 ◽  
Author(s):  
Pibulchai Kasemphaibulsuk ◽  
Marcel Holzner ◽  
Takashi Kuboki ◽  
Andrew Hrymak
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Fiber Reinforced ◽  
Polypropylene Composites ◽  
Glass Fiber Reinforced ◽  
Foam Injection Molding

scholarly journals Ultrasonic injection molding of glass fiber reinforced polypropylene parts using tungsten carbide-cobalt mold core

2021 ◽  
pp. 109771
Author(s):  
Xiong Liang ◽  
Yongjing Liu ◽  
Zehang Liu ◽  
Jiang Ma ◽  
Zhenxuan Zhang ◽  
...  
Keyword(s):  
Injection Molding ◽  
Tungsten Carbide ◽  
Glass Fiber ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced

scholarly journals A Fatigue Damage Model for Life Prediction of Injection-Molded Short Glass Fiber-Reinforced Thermoplastic Composites

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2250
Author(s):  
Mohammad Amjadi ◽  
Ali Fatemi
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Fatigue Damage ◽  
Life Prediction ◽  
Glass Fibers ◽  
Damage Model ◽  
Fiber Reinforced ◽  
Short Glass Fiber ◽  
Glass Fiber Reinforced ◽  
Short Glass

Short glass fiber-reinforced (SGFR) thermoplastics are used in many industries manufactured by injection molding which is the most common technique for polymeric parts production. Glass fibers are commonly used as the reinforced material with thermoplastics and injection molding. In this paper, a critical plane-based fatigue damage model is proposed for tension–tension or tension–compression fatigue life prediction of SGFR thermoplastics considering fiber orientation and mean stress effects. Temperature and frequency effects were also included by applying the proposed damage model into a general fatigue model. Model predictions are presented and discussed by comparing with the experimental data from the literature.

Crystallization and Mechanical Properties of Glass Fiber Reinforced Polypropylene Composites Molded by Rapid Heat Cycle Molding

2020 ◽  
Vol 21 (12) ◽  
pp. 2915-2926
Author(s):  
Aimin Zhang ◽  
Guoqun Zhao ◽  
Jialong Chai ◽  
Junji Hou ◽  
Chunxia Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Fiber Reinforced ◽  
Heat Cycle ◽  
Polypropylene Composites ◽  
Glass Fiber Reinforced

scholarly journals Warpage Reduction of Glass Fiber Reinforced Plastic Using Microcellular Foaming Process Applied Injection Molding

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 360 ◽  
Author(s):  
Hyun Kim ◽  
Joo Sohn ◽  
Youngjae Ryu ◽  
Shin Kim ◽  
Sung Cha
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Fiber Orientation ◽  
Mechanical And Thermal Properties ◽  
Micro Ct ◽  
Fiber Reinforced ◽  
Foaming Process ◽  
Microcellular Foaming ◽  
Glass Fiber Reinforced ◽  
The Impact

This study analyzes the fundamental principles and characteristics of the microcellular foaming process (MCP) to minimize warpage in glass fiber reinforced polymer (GFRP), which is typically worse than that of a solid polymer. In order to confirm the tendency for warpage and the improvement of this phenomenon according to the glass fiber content (GFC), two factors associated with the reduction of the shrinkage difference and the non-directionalized fiber orientation were set as variables. The shrinkage was measured in the flow direction and transverse direction, and it was confirmed that the shrinkage difference between these two directions is the cause of warpage of GFRP specimens. In addition, by applying the MCP to injection molding, it was confirmed that warpage was improved by reducing the shrinkage difference. To further confirm these results, the effects of cell formation on shrinkage and fiber orientation were investigated using scanning electron microscopy, micro-CT observation, and cell morphology analysis. The micro-CT observations revealed that the fiber orientation was non-directional for the MCP. Moreover, it was determined that the mechanical and thermal properties were improved, based on measurements of the impact strength, tensile strength, flexural strength, and deflection temperature for the MCP.

Effect of Processing Conditions on the Shrinkage and Warpage of Glass Fiber Reinforced PP Using Microcellular Injection Molding

2012 ◽  
Vol 501 ◽  
pp. 294-299 ◽  
Author(s):  
Zhi Bian ◽  
Peng Cheng Xie ◽  
Yu Mei Ding ◽  
Wei Min Yang
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Process Conditions ◽  
Fiber Reinforced ◽  
Injection Speed ◽  
Glass Fiber Reinforced ◽  
Microcellular Injection Molding ◽  
Molded Parts

This study was aimed at understanding how the process conditions affected the dimensional stability of glass fiber reinforced PP by microcellular injection molding. A design of experiments (DOE) was performed and plane test specimens were produced for the shrinkage and warpage analysis. Injection molding trials were performed by systematically adjusting six process parameters (i.e., Injection speed, Injection pressure, Shot temperature, SCF level, Mold temperature, and Cooling time). By analyzing the statistically significant main and two-factor interaction effects, the results showed that the supercritical fluid (SCF) level and the injection speed affected the shrinkage and warpage of microcellular injection molded parts the most.

Sign in / Sign up

Export Citation Format

Share Document