Ethylene vinyl acetate copolymer nanocomposites based on (un)modified sepiolite: Flame retardancy, thermal, and mechanical properties

2015 ◽  
Vol 38 (7) ◽  
pp. 1302-1310 ◽  
Author(s):  
Hossein Cheraghi Bidsorkhi ◽  
Hossein Adelnia ◽  
Nafiseh Naderi ◽  
Nima Moazeni ◽  
Zurina Mohamad
Keyword(s):  
Mechanical Properties ◽  
Vinyl Acetate ◽  
Flame Retardancy ◽  
Ethylene Vinyl Acetate ◽  
Thermal And Mechanical Properties ◽  
Acetate Copolymer ◽  
Ethylene Vinyl Acetate Copolymer

Effect of electron beam irradiation on the thermal and mechanical properties of ethylene-vinyl acetate copolymer/polyamide blends

2020 ◽  
pp. 096739112093010
Author(s):  
Jawad Ahmed ◽  
Yong Zhang
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Vinyl Acetate ◽  
Irradiation Dose ◽  
Ethylene Vinyl Acetate ◽  
Cross Linking ◽  
Thermal And Mechanical Properties ◽  
Beam Irradiation ◽  
Acetate Copolymer ◽  
Ethylene Vinyl Acetate Copolymer

The effect of electron beam (e-beam) irradiation on the thermal and mechanical properties of ethylene-vinyl acetate copolymer/ternary polyamide (EVA/tPA) blends was studied. The e-beam irradiation was carried out over a range of dose from 50 kGy to 500 kGy with trimethylolpropane trimethacrylate (TMPTMA) and triallyl isocyanurate (TAIC) as cross-linking coagents. With increasing irradiation dose, the gel fraction of the EVA/tPA blends increased significantly. After irradiated by e-beam at 500 kGy, the insoluble fraction of EVA/tPA blends with 3 parts per hundred rubber TMPTMA increased from 28% to 86%. The tensile strength of EVA/tPA/TMPTMA-3 (70/30/3) considerably increased up to 172% with a value of 10.01 MPa at 500 kGy due to an increase in cross-linking compared to the EVA/tPA/TAIC-3 (70/30/3) blend. However, the melting temperature and crystallization peak temperature of EVA/tPA blends decreased with increasing irradiation dose. Thermogravimetric analysis demonstrated that the irradiation cross-linking could improve the thermal stability of the EVA/tPA blends. The degradation kinetics of the EVA/tPA blends at elevated temperatures were studied using the Kissinger, Flynn–Wall–Ozawa, and Friedman methods. Irradiation cross-linked EVA/tPA blends exhibited a remarkable improvement in their oil resistance, with the identified improvement being most prominent in the EVA/tPA/TMPTMA-3 blend.

scholarly journals INFLUENCE OF CARBON FIBER ON THE COMBUSTION BEHAVIOR, THERMAL STABILITY AND MECHANICAL PROPERTIES OF ETHYLENE-VINYL ACETATE COPOLYMER (EVA) AND 9,10-DIHYDRO-9-OXA-10-PHOSPHAPHENANTHRENE-10-OXIDE (DOPO) COMPOSITES

10.6036/10031 ◽  
2021 ◽  
Vol 96 (3) ◽  
pp. 302-308
Author(s):  
XIAN WANG ◽  
JUNYI DAI ◽  
TIANQING XING ◽  
JINLONG ZHUO
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Thermogravimetric Analysis ◽  
Carbon Fiber ◽  
Heat Release ◽  
Vinyl Acetate ◽  
Flame Retardancy ◽  
Ethylene Vinyl Acetate ◽  
Acetate Copolymer ◽  
Ethylene Vinyl Acetate Copolymer

Ethylene-vinyl acetate copolymer (EVA) is widely used due to its good processability, low density, and low temperature resistance. However, it burns easily and has several disadvantages, such as a high heat release rate and melt dripping, and it emits large amounts of smog and toxic harmful gases. These disadvantages greatly limit the application of EVA in the wire and cable field. In this study, a series of carbon fiber (CF)/9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO)/EVA composites are prepared through melt compounding to improve the flame retardancy and mechanical properties of EVA. The flame retardancy, thermal stability, and mechanical properties of the composites are studied through microscale combustion calorimeter experiments, cone calorimeter tests, thermogravimetric analysis, digital camera, and tensile measurements. Results indicate that among the six samples, the EVA-5 composite with 4.0 wt% CF, 16.0 wt% DOPO, and 80 wt% EVA has the highest limiting oxygen index value (25.1%) and reaches the V-1 level of the Underwriters Laboratory-94 test. Compare with that of pure EVA, the peak heat release rate of the EVA-5 composite has reduced by 30.2% and 47.7%. In addition, the total heat release of EVA-5 reduces by 17.0% and 34.8% relative to that of pure EVA. Data of thermogravimetric analysis show that the thermal stability of CF/DOPO/EVA improves with the increase in CF loading. Moreover, the tensile strength and elongation-at-break values of EVA-5 are 14.30 MPa and 1142.87%, respectively, indicating that this material can maintain good mechanical properties. CF not only enhances the tensile properties of EVA but also acts as a skeleton during burning. This action could increase the strength of the carbon layer and enhance the flame-retardant effect of DOPO. CF and DOPO have an enhanced synergistic effect that could improve the flame retardancy, thermal stability, and mechanical properties of EVA composites. This work provides a theoretical basis for the preparation and production of CF/DOPO/EVA composites with good comprehensive performance. Keywords: thylene-vinyl acetate copolymer; 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide; carbon fiber; flame retardant; synergistic effects

Role of montmorillonite in flame retardancy of ethylene–vinyl acetate copolymer

2006 ◽  
Vol 91 (3) ◽  
pp. 593-599 ◽  
Author(s):  
Andrea Szép ◽  
András Szabó ◽  
Nikoletta Tóth ◽  
Péter Anna ◽  
György Marosi
Keyword(s):  
Vinyl Acetate ◽  
Flame Retardancy ◽  
Ethylene Vinyl Acetate ◽  
Acetate Copolymer ◽  
Ethylene Vinyl Acetate Copolymer
Sign in / Sign up

Export Citation Format

Share Document