Mechanical properties of wood plastic composite panels made from waste fiberboard and particleboard

2008 ◽  
Vol 29 (6) ◽  
pp. 606-610 ◽  
Author(s):  
Majid Chaharmahali ◽  
Mehdi Tajvidi ◽  
Saeed Kazemi Najafi
Keyword(s):  
Mechanical Properties ◽  
Composite Panels ◽  
Wood Plastic Composite ◽  
Plastic Composite

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

Analysis on mechanical properties of wood plastic composite

2020 ◽  
Author(s):  
K. Bhaskar ◽  
D. Jayabalakrishnan ◽  
M. Vinoth Kumar ◽  
S. Sendilvelan ◽  
M. Prabhahar
Keyword(s):  
Mechanical Properties ◽  
Wood Plastic Composite ◽  
Plastic Composite

scholarly journals Evaluasi Kuat Tumpu Alat Sambung Baut pada Papan WPC dari Limbah Sengon dan Plastik HDPE

2016 ◽  
Vol 22 (2) ◽  
pp. 129
Author(s):  
Yudhi Arnandha ◽  
Iman Satyarno ◽  
Ali Awaludin ◽  
Arfiati Fardhani
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Shear Wall ◽  
High Shear ◽  
Wood Plastic Composite ◽  
Bearing Strength ◽  
Plastic Composite ◽  
Structural Purpose ◽  
High Shear Strength ◽  
Bolt Diameter

Wood Plastic Composite (WPC) is wood based material that been produce by mixing sawdust as main composition and plastic polymer as bonding agent. Nowadays, WPC board already been produced in Indonesia using Sengon sawdust and recycle HDPE plastic. Sengon sawdust was used as WPC since its availability from plywood production waste, moreover HDPE plastic considered had higher strength and more rigid than PET plastic. WPC occasionally being used as non structural material, moreover from previous study about mechanical properties of WPC, it was found that WPC Sengon has high shear strength around 25 – 30 MPa. These lead that WPC Sengon had a potential used as shear wall sheathing, thus additional research need to be conducted in order to study the type of bolt and diameter of the bolt can be used for these shear wall. This study aimed to investigate the dowel bearing of bolt using full hole method based on ASTM D5764 with type and bolt diameter as specimen variation. Two types of bolt were used in this study; stainless bolt and standard bolt with diameter each of 6 mm, 8 mm, 10 mm and 12 mm. According to ANOVA, there was insignificant result between stainless bolt and standard one, but there was significant result based on diameter of the bolt. Hereafter, it can be recommended the used of 10 mm diameter of bolt for structural purpose with dowel bearing strength around 67 – 70 MPa.

The Influence of Fiber Surface Treatment and SBR as Impact Modifier on Rheological Behavior and Mechanical Properties of Wood Plastic Composite from Acrylate-Styrene-Acrylonitrile and Bagasse

2017 ◽  
Vol 737 ◽  
pp. 281-286 ◽  
Author(s):  
Pornsri Sapsrithong ◽  
Kesinee Puksattee ◽  
Kingkaew Saewjaidee ◽  
Navapon Pensuk ◽  
Apaipan Rattanapan
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Surface Treatment ◽  
Rheological Behavior ◽  
Fiber Surface ◽  
Wood Plastic Composite ◽  
Plastic Composite ◽  
Styrene Acrylonitrile ◽  
Impact Modifier ◽  
Fiber Surface Treatment

Morphology, mechanical properties and rheological behavior of wood plastic composite, derived from acrylate-styrene-acrylonitrile (ASA) and bagasse which was treated with potassium permanganate (KMnO4) and using styrene butadiene rubber (SBR) as impact modifier, were reported. The effect of fiber surface treatment with KMnO4 and different amount of SBR on properties of wood plastic composite, prepared from ASA and 50 phr of bagasse, were investigated. Wood plastic composites (both treated and untreated) with varying amount of SBR, as impact modifier from 0-15 wt% of ASA, were prepared by melt-blending technique. The specimens were shaped with a compression molding machine and characterized, including morphology, impact strength, flexural properties and rheological behavior. It was demonstrated that the fiber surface treatment, using KMnO4, could effectively impove interfacial adhesion between bagasse and ASA matrix. These led to an improvement of morphology and mechanical properties such as impact strength, flexural strength and modulus. SEM micrographs revealed that the interfacial modification enhanced the interfacial adhesion between bagasse (fiber) and ASA (matrix) causing an increasing of shear stress and shear viscosity. Additionally, the effect of amount of SBR, as impact modifier, was also reported. The resulted showed that the impact strength was improved with increasing the amount of SBR (up 5 wt% of ASA) whereas, flexural strength and modulus were found to decrease with increasing SBR content.

Properties of wood plastic composite panels made from waste sanding dusts and nanoclay

2013 ◽  
Vol 48 (14) ◽  
pp. 1661-1669 ◽  
Author(s):  
Mehrab Madhoushi ◽  
Arash Chavooshi ◽  
Alireza Ashori ◽  
Martin P Ansell ◽  
Alireza Shakeri
Keyword(s):  
Composite Panels ◽  
Wood Plastic Composite ◽  
Plastic Composite

Study of Surface Quality and Mechanical Properties of Composite Material Based on Natural Reinforcement

2016 ◽  
Vol 821 ◽  
pp. 471-478
Author(s):  
Zuzana Hutyrová ◽  
Dušan Mitaľ ◽  
Marta Harničárová ◽  
Jozef Zajac ◽  
Jan Valíček
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Tensile Test ◽  
Surface Quality ◽  
Bending Test ◽  
Wood Plastic Composite ◽  
Radiographic Method ◽  
Plastic Composite

This paper presents problem of the examination of the inhomogeneity of composite material on the base of wood plastic composite. It deals with evaluation of mechanical properties after tensile test and triax-bending test of a composite were assessed in relation to images acquired from radiographic method – metrotomography (using radiographic method which has an explanatory value in terms of evaluation of volume defects and in a figurative sense, also of the conduct of cracks on the surface after machining).

Dynamic Thermal Mechanical Behaviors and Mechanical Properties of Reversible Thermochromism Wood-Plastic Composite

2017 ◽  
Vol 727 ◽  
pp. 571-578
Author(s):  
Yue Qin Wen ◽  
Ying Ying Sun ◽  
Jian Feng Xu ◽  
Jing Bing Chen ◽  
Xin Xiang Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Color Change ◽  
Loss Modulus ◽  
Wood Plastic Composite ◽  
Advantages And Disadvantages ◽  
Plastic Composite ◽  
Before And After ◽  
The Difference ◽  
Reversible Thermochromism

To prepare a late-model and functional wood-plastic composite (WPC), the reversible thermochromism crystal violet lactone microcapsule was prepared by situ polymerization, then fabricated reversible thermochromism WPC by microcapsule and low density polyethylene with Maleic anhydride grafted polyethylene. Comparing the L, a and b data of apparent color of reversible thermochromism WPC, the value of chromatism (ΔE) showed the difference of heating before and after, it was also measured to characterize the color-change level; the mechanical properties of ordinary WPC and reversible thermochromism WPC were measured respectively to compare the advantages and disadvantages of two kinds of WPC; Then the storage modulus and loss modulus of ordinary WPC and reversible thermochromism WPC were determined to distinguish the good from the bad of two kinds of composites. The results indicated that the reversible thermochromism WPC is a functional composite with noticeable color-changed effects, and tensile strength, bending strength and interface compatibility were better than ordinary WPC, but had worse impact property contrarily.

Mechanical Properties of Acrylate-Styrene-Acrylonitrile/Bagasse Composites

2013 ◽  
Vol 747 ◽  
pp. 355-358 ◽  
Author(s):  
Pornsri Pakeyangkoon ◽  
Benjawan Ploydee
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
Roll Mill ◽  
The Matrix ◽  
Styrene Acrylonitrile

Mechanical properties of wood plastic composite, prepared from acrylate-styrene-acrylonitrile (ASA) and bagasse, were investigated. In this study, 10 to 50 phr of bagasse were used in order to obtain the wood plastic composite with superior mechanical properties. The wood plastic composites in the study were prepared by melt-blending technique. All materials were mixed by using a two-roll-mill, shaped into sheets by a compression molding machine and the specimens were cut with a cutting machine. Youngs modulus, flexural strength, flexural modulus, impact strength and hardness of the wood plastic composites were investigated and found to improve with increasing bagasse content. However, some composite properties, i.e., impact strength, was decreased by adding the bagasse and then become steady when the amount of bagasse added was more than 30 phr. It was concluded that wood plastic composites with the desirable mechanical properties can be formulated using ASA as the matrix polymer and 50 phr of bagasse.

Sign in / Sign up

Export Citation Format

Share Document