Mechanism of fiber–matrix separation in ribbed compression molded parts

2007 ◽  
Vol 28 (4) ◽  
pp. 451-457 ◽  
Author(s):  
Alejandro Londoño-Hurtado ◽  
Juan Pablo Hernandez-Ortiz ◽  
T.A. Osswald
Keyword(s):  
Matrix Separation ◽  
Molded Parts ◽  
Fiber Matrix

scholarly journals A Force-Balanced Fiber Retardation Model to Predict Fiber-Matrix-Separation during Polymer Processing

2020 ◽  
Vol 4 (4) ◽  
pp. 165
Author(s):  
Christoph Kuhn ◽  
Simon Wehler
Keyword(s):  
Fiber Orientation ◽  
Prediction Models ◽  
Compression Molding ◽  
Polymer Processing ◽  
Force Balance ◽  
Particle Simulation ◽  
Retardation Factor ◽  
Two Phase ◽  
Matrix Separation ◽  
Fiber Matrix

The use of discontinuous fiber reinforced composites in injection and compression molding faces a number of challenges regarding process-induced changes in microstructure, which have a significant influence on the mechanical properties of the final component. The changes in final microstructure are caused by complex fiber movements, such as fiber orientation, attrition and accumulation during flow. While there are existing phenomenological prediction models for both fiber orientation and attrition, the prediction of fiber accumulation due to fiber-matrix separation is currently only possible with a complex mechanistic particle simulation, which is not applicable in industrial simulations. A simplified phenomenological model, the fiber retardation model (FRM), for the prediction of fiber-matrix separation in commercially available software tools is presented in this paper. The model applies a force balance onto an interacting two phase flow of polymer melt and fiber phase and applies a retardation factor Κ to calculate the slowing and accumulation of the fiber phase. The general model is successfully applied to a simple compression molding simulation.

A Parametric Study on Compression Molding of Reference Parts with Integrated Features Using Carbon Composite Production Waste

2015 ◽  
Vol 651-653 ◽  
pp. 458-463
Author(s):  
Mohammed Iqbal Abdul Rasheed ◽  
Bert Rietman ◽  
Hendrikus Antonius Visser ◽  
Remko Akkerman
Keyword(s):  
Compression Molding ◽  
Carbon Composite ◽  
Stiffened Plates ◽  
Consolidation Pressure ◽  
Matrix Separation ◽  
Aspect Ratios ◽  
Composite Production ◽  
Fiber Matrix ◽  
Jamming Effect ◽  
Opening Width

Compression molding of near net-shaped rib-stiffened plates has been performed for a parametric investigation on the filling behavior of chopped woven flake reinforcements. The experimental investigation showed that different aspect ratios of ribs can be filled completely within the tested maximum ratio of flake size to rib opening width of 6.25 and a maximum consolidation pressure of 15 bar. However, defects such as voids, non-impregnated regions and fiber matrix separation may arise depending on the combination of parameters and a mechanical jamming effect caused by the woven architecture of the flakes. A tendency for a limiting consolidation pressure is observed based on the fiber matrix separation. The ability to re-use thermoplastic prepreg cutting waste has been demonstrated.

Techniques for Transmission Electron Microscopy of Fiber-Matrix Interfaces in Aluminum Alloy-Boron Composites by Ion Erosio

1971 ◽  
Vol 29 ◽  
pp. 204-205
Author(s):  
G. G. Shaw
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Aluminum Alloy ◽  
Electron Beam ◽  
Pure Aluminum ◽  
Ion Milling ◽  
Transmission Electron ◽  
Fiber Matrix ◽  
Ion Erosion ◽  
Row Of Fibers

The morphology and composition of the fiber-matrix interface can best be studied by transmission electron microscopy and electron diffraction. For some composites satisfactory samples can be prepared by electropolishing. For others such as aluminum alloy-boron composites ion erosion is necessary.When one wishes to examine a specimen with the electron beam perpendicular to the fiber, preparation is as follows: A 1/8 in. disk is cut from the sample with a cylindrical tool by spark machining. Thin slices, 5 mils thick, containing one row of fibers, are then, spark-machined from the disk. After spark machining, the slice is carefully polished with diamond paste until the row of fibers is exposed on each side, as shown in Figure 1.In the case where examination is desired with the electron beam parallel to the fiber, preparation is as follows: Experimental composites are usually 50 mils or less in thickness so an auxiliary holder is necessary during ion milling and for easy transfer to the electron microscope. This holder is pure aluminum sheet, 3 mils thick.

Characterization of interfaces in CVD-coated nicalon fiber-reinforced SiC

1989 ◽  
Vol 47 ◽  
pp. 556-557
Author(s):  
K.L. More ◽  
R.A. Lowden
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Chemical Vapor ◽  
Chemical Vapor Infiltration ◽  
Frictional Stress ◽  
Fiber Reinforced ◽  
Pull Out ◽  
Carbon Coated ◽  
Fiber Matrix

The mechanical properties of fiber-reinforced composites are directly related to the nature of the fiber-matrix bond. Fracture toughness is improved when debonding, crack deflection, and fiber pull-out occur which in turn depend on a weak interfacial bond. The interfacial characteristics of fiber-reinforced ceramics can be altered by applying thin coatings to the fibers prior to composite fabrication. In a previous study, Lowden and co-workers coated Nicalon fibers (Nippon Carbon Company) with silicon and carbon prior to chemical vapor infiltration with SiC and determined the influence of interfacial frictional stress on fracture phenomena. They found that the silicon-coated Nicalon fiber-reinforced SiC had low flexure strengths and brittle fracture whereas the composites containing carbon coated fibers exhibited improved strength and fracture toughness. In this study, coatings of boron or BN were applied to Nicalon fibers via chemical vapor deposition (CVD) and the fibers were subsequently incorporated in a SiC matrix. The fiber-matrix interfaces were characterized using transmission and scanning electron microscopy (TEM and SEM). Mechanical properties were determined and compared to those obtained for uncoated Nicalon fiber-reinforced SiC.

Sign in / Sign up

Export Citation Format

Share Document