Mechanical properties of phenol/formaldehyde resin composites reinforced by cellulose microcrystal with different aspect ratio extracted from sisal fiber

2016 ◽  
Vol 28 (8) ◽  
pp. 1013-1019
Author(s):  
Chun Wei ◽  
Wu Wang ◽  
Hongxia Liu ◽  
Aimiao Qin ◽  
Chuanbai Yu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Sisal Fiber ◽  
Formaldehyde Resin ◽  
Resin Composites ◽  
Cellulose Microcrystal

Novolak Type Phenol Formaldehyde Resin from Waste Brown-Rotted Wood

2011 ◽  
Vol 217-218 ◽  
pp. 490-494
Author(s):  
Gai Yun Li ◽  
Te Fu Qin
Keyword(s):  
Mechanical Properties ◽  
Phosphoric Acid ◽  
Thermal Property ◽  
Significant Influence ◽  
Phenol Formaldehyde ◽  
Product Yield ◽  
Flow Property ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Liquefied Wood

The waste brown-rotted wood was liquefied in phenol with phosphoric acid as a catalyst and the resulting liquefied products were condensed with formaldehyde to yield novolak liquefied wood-based phenol formaldehyde resin (LWF). The results showed that brown-rotted wood could be almost completely liquefied within 0.5 h at phenol to wood (P/W) ratio 2. An increase in P/W ratio from 2 to 3 slightly improved the flow property of LWF, but accompanied by decreasing the product yield from approximately 140 to 120 %. The increase of liquefaction time from 30 min to 60 min did not have a significant influence on the resulting LWF. The thermofluidity of LWF were compared to that of the commercial novolak PF resin, and could be used to make moldings with similar thermal property and mechanical properties to those obtained from the conventional novolak PF resin.

scholarly journals Self-adhesion X-ray Shielding Composite Material of EPDM Rubber with Barite: Mechanical Properties

2020 ◽  
Vol 57 (1) ◽  
pp. 28-36
Author(s):  
Vasiliy Cherkasov ◽  
Yuiy Yurkin ◽  
Valeriy Avdonin ◽  
Dmitriy Suntsov
Keyword(s):  
Mechanical Properties ◽  
Phenol Formaldehyde ◽  
Peel Strength ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Adhesion Properties ◽  
X Ray ◽  
Industrial Oil ◽  
Oil Concentration ◽  
Free Material

It is actual now to work out new radiation protecting sheeting on the basis of non-curing polymeric composition which possess self-adhesion properties, are easily mounted and dismantled and provide high tightness and low permeability. Mechanical properties of non-curing composites consisting of ethylene propylene diene monomer (EPDM), industrial oil (IO), alkyl phenol-formaldehyde resin (PF) with addition of barite (52 %) to the total material volume were investigated in this article. The aim of investigation is to find optimal content of the above mentioned components at which it would be possible to get the following properties: composite would be sticky enough (peel strength not less than 4 N/cm); character of a separation would be cohesive (on a material) and thus there would be no migration of softener and satisfactory resistance of fluidity. The results showed that PF addition till 20 % in the system EPDM/PF leads to the increasing of adhesive strength, in this case optimal oil concentration in the system EPDM/PF/IO is in the interval from 45 till 55 %. New self-adhesion lead-free material, exhibited higher X-ray-shielding properties, is also received in the result of investigation.

Physico-mechanical characteristics and phase composition of unburned periclase-carbon refractories on modified phenol-formaldehyde resin

2019 ◽  
pp. 29-33
Author(s):  
D. A. Brazhnik ◽  
G. D. Semchenko ◽  
G. N. Shabanova ◽  
E. E. Starolat ◽  
I. N. Rozhko ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Phase Composition ◽  
Mechanical Characteristics ◽  
Carbon Materials ◽  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Ethyl Silicate ◽  
Ammonium Citrate ◽  
Formaldehyde Resin

The possibilities of improving the physico-mechanical properties of periclase-carbon materials by modifying the phenol-formaldehyde resin (PFR) with organoinorganic complexes are described. The composition of the modifying additives, the phase composition of the materials after the PFR hardening are given, the influence of modifiers on the formation of the structure of materials is established. It is shown that the introduction of ethyl silicate or hydrolyzed ethyl silicate into liquid PFR during preparation of the charge contributes to the formation of SiC in the phase composition. The conclusion is made about the rationality of the introduction of ethyl silicate in an amount of from 0,66 to 1 wt. % and the prospects of introducing nickel oxalate into a liquid PFR together with ammonium citrate to increase the compressive strength of periclase-carbon materials up to 60 MPa. Ill. 7. Ref. 9.

279. Graphite-phenol formaldehyde resin composites

Carbon ◽  
1982 ◽  
Vol 20 (2) ◽  
pp. 155-156
Author(s):  
A.M. Lyons ◽  
V.G. Lambrecht
Keyword(s):  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Resin Composites
Sign in / Sign up

Export Citation Format

Share Document