Eight‐Node Hexahedral Elements for Gradient Elasticity Analysis

2021 ◽  
Author(s):  
W. C. Yuan ◽  
K. Y. Sze
Keyword(s):  
Gradient Elasticity ◽  
Elasticity Analysis ◽  
Hexahedral Elements

Finite Element Analysis of the Distributed Vibration Absorbers for Structural Noise Control

2005 ◽  
Author(s):  
Ashwini Gautam ◽  
Chris Fuller ◽  
James Carneal
Keyword(s):  
Finite Element ◽  
Numerical Model ◽  
Base Plate ◽  
Element Model ◽  
Fe Model ◽  
Vibration Absorbers ◽  
Element Analysis ◽  
Poroelastic Media ◽  
Hexahedral Elements ◽  
Component Models

This work presents an extensive analysis of the properties of distributed vibration absorbers (DVAs) and their effectiveness in controlling the sound radiation from the base structure. The DVA acts as a distributed mass absorber consisting of a thin metal sheet covering a layer of acoustic foam (porous media) that behaves like a distributed spring-mass-damper system. To assess the effectiveness of these DVAs in controlling the vibration of the base structures (plate) a detailed finite elements model has been developed for the DVA and base plate structure. The foam was modeled as a poroelastic media using 8 node hexahedral elements. The structural (plate) domain was modeled using 16 degree of freedom plate elements. Each of the finite element models have been validated by comparing the numerical results with the available analytical and experimental results. These component models were combined to model the DVA. Preliminary experiments conducted on the DVAs have shown an excellent agreement between the results obtained from the numerical model of the DVA and from the experiments. The component models and the DVA model were then combined into a larger FE model comprised of a base plate with the DVA treatment on its surface. The results from the simulation of this numerical model have shown that there has been a significant reduction in the vibration levels of the base plate due to DVA treatment on it. It has been shown from this work that the inclusion of the DVAs on the base plate reduces their vibration response and therefore the radiated noise. Moreover, the detailed development of the finite element model for the foam has provided us with the capability to analyze the physics behind the behavior of the distributed vibration absorbers (DVAs) and to develop more optimized designs for the same.

A nonlocal operator method for finite deformation higher-order gradient elasticity

2021 ◽  
Vol 384 ◽  
pp. 113963
Author(s):  
Huilong Ren ◽  
Xiaoying Zhuang ◽  
Nguyen-Thoi Trung ◽  
Timon Rabczuk
Keyword(s):  
Finite Deformation ◽  
Gradient Elasticity ◽  
Operator Method ◽  
Higher Order ◽  
Nonlocal Operator

Experimental and Theoretical Study of the Contact Mechanics of Five Total Knee Joint Replacements

1995 ◽  
Vol 209 (4) ◽  
pp. 225-231 ◽  
Author(s):  
T Stewart ◽  
Z M Jin ◽  
D Shaw ◽  
D D Auger ◽  
M Stone ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Knee Joint ◽  
Contact Pressure ◽  
Contact Stress ◽  
Linear Elasticity ◽  
Contact Area ◽  
Elasticity Analysis ◽  
Joint Replacements ◽  
Total Knee ◽  
Maximum Contact

The tibio-femoral contact area in five current popular total knee joint replacements has been measured using pressure-sensitive film under a normal load of 2.5 kN and at several angles of flexion The corresponding maximum contact pressure has been estimated from the measured contact areas and found to exceed the point at which plastic deformation is expected in the ultra-high molecular weight polyethylene (UHMWPE) component particularly at flexion angles near 90°. The measured contact area and the estimated maximum contact stress have been found to be similar in magnitude for all of the five knee joint replacements tested. A significant difference, however, has been found in maximum contact pressure predicted from linear elasticity analysis for the different knee joints. This indicates that varying amounts of plastic deformation occurred in the polyethylene component in the different knee designs. It is important to know the extent of damage as knees with large amounts of plastic deformation are more likely to suffer low cycle fatigue failure. It is therefore concluded that the measurement of contact areas alone can be misleading in the design of and deformation in total knee joint replacements. It is important to modify geometries to reduce the maximum contact stress as predicted from the linear elasticity analysis, to below the linear elastic limit of the plastic component.

scholarly journals Non-local criteria for the borehole problem: Gradient Elasticity versus Finite Fracture Mechanics

Meccanica ◽  
2021 ◽  
Author(s):  
A. Sapora ◽  
G. Efremidis ◽  
P. Cornetti
Keyword(s):  
Stress Concentration ◽  
Fracture Mechanics ◽  
Elastic Material ◽  
Fracture Criterion ◽  
Biaxial Loading ◽  
Gradient Elasticity ◽  
Energy Conditions ◽  
Material Behaviour ◽  
Finite Fracture Mechanics ◽  
Non Local

AbstractTwo nonlocal approaches are applied to the borehole geometry, herein simply modelled as a circular hole in an infinite elastic medium, subjected to remote biaxial loading and/or internal pressure. The former approach lies within the framework of Gradient Elasticity (GE). Its characteristic is nonlocal in the elastic material behaviour and local in the failure criterion, hence simply related to the stress concentration factor. The latter approach is the Finite Fracture Mechanics (FFM), a well-consolidated model within the framework of brittle fracture. Its characteristic is local in the elastic material behaviour and non-local in the fracture criterion, since crack onset occurs when two (stress and energy) conditions in front of the stress concentration point are simultaneously met. Although the two approaches have a completely different origin, they present some similarities, both involving a characteristic length. Notably, they lead to almost identical critical load predictions as far as the two internal lengths are properly related. A comparison with experimental data available in the literature is also provided.

Sign in / Sign up

Export Citation Format

Share Document