3D Viscoelastic Computational Grains with Spherical Inclusions with or without Interphases/Coatings for Micromechanical Modeling of Heterogeneous Materials

2021 ◽  
Author(s):  
Yezeng Huang ◽  
Guannan Wang ◽  
Leiting Dong ◽  
Satya N. Atluri
Keyword(s):  
Heterogeneous Materials ◽  
Micromechanical Modeling ◽  
Spherical Inclusions

Micromechanical Modeling of Heterogeneous Materials with Irregularly Shaped Pores

2011 ◽  
Vol 488-489 ◽  
pp. 327-330
Author(s):  
Igor Tsukrov ◽  
Borys Drach
Keyword(s):  
Mechanical Properties ◽  
Numerical Analysis ◽  
Heterogeneous Materials ◽  
Micromechanical Modeling ◽  
Pore Geometry ◽  
Irregular Shapes ◽  
Mechanical Properties Of Materials ◽  
Properties Of Materials ◽  
Compliance Contribution Tensor

An approach to predict the overall mechanical properties of materials containing pores of irregular shapes is described. Micromechanical modeling is performed by evaluating cavity compliance contribution tensors of individual pores [1] which are then used as an input for well-developed homogenization models. The cavity compliance contribution tensor can be found either analytically or numerically depending on the pore geometry and the level of anisotropy of the surrounding material. The results of numerical analysis can be used to compare the ability of differently shaped pores to initiate fracture.

Observation of dislocations in dynamically loaded Cu-SiO2

1986 ◽  
Vol 44 ◽  
pp. 424-425
Author(s):  
D. S. Pritchard
Keyword(s):  
Electron Microscope ◽  
Strain Rate ◽  
Single Crystal ◽  
Transmission Electron Microscope ◽  
Volume Fraction ◽  
Screw Dislocations ◽  
Spherical Inclusions ◽  
Transmission Electron ◽  
Crystal Dispersion ◽  
Strain Rate Loading

The effect of varying the strain rate loading conditions in compression on a copper single crystal dispersion-hardened with SiO2 particles has been examined. These particles appear as small spherical inclusions in the copper lattice and have a volume fraction of 0.6%. The structure of representative crystals was examined prior to any testing on a transmission electron microscope (TEM) to determine the nature of the dislocations initially present in the tested crystals. Only a few scattered edge and screw dislocations were viewed in those specimens.

The microstructure change of low-carbon electrical steels by residual aluminum

1989 ◽  
Vol 47 ◽  
pp. 286-287
Author(s):  
C.K. Hou ◽  
C.T. Hu ◽  
Sanboh Lee
Keyword(s):  
Annealing Treatment ◽  
Low Carbon ◽  
Electrical Steels ◽  
Vacuum Degassing ◽  
Spherical Inclusions ◽  
Residual Aluminum ◽  
Average Grain Size ◽  
The Matrix ◽  
Fine Size ◽  
To Come

The fully processed low-carbon electrical steels are generally fabricated through vacuum degassing to reduce the carbon level and to avoid the need for any further decarburization annealing treatment. This investigation was conducted on eighteen heats of such steels with aluminum content ranging from 0.001% to 0.011% which was believed to come from the addition of ferroalloys.The sizes of all the observed grains are less than 24 μm, and gradually decrease as the content of aluminum is increased from 0.001% to 0.007%. For steels with residual aluminum greater than 0. 007%, the average grain size becomes constant and is about 8.8 μm as shown in Fig. 1. When the aluminum is increased, the observed grains are changed from the uniformly coarse and equiaxial shape to the fine size in the region near surfaces and the elongated shape in the central region. SEM and EDAX analysis of large spherical inclusions in the matrix indicate that silicate is the majority compound when the aluminum propotion is less than 0.003%, then the content of aluminum in compound inclusion increases with that in steel.

Sign in / Sign up

Export Citation Format

Share Document