Semianalytical modeling on 3D stress redistribution during hydraulic fracturing stimulation and its effects on natural fracture reactivation

2020 ◽  
Vol 44 (8) ◽  
pp. 1184-1199
Author(s):  
Jun Ge ◽  
Sukhvarsh Jerath ◽  
Ahmad Ghassemi
Keyword(s):  
Hydraulic Fracturing ◽  
Stress Redistribution ◽  
Natural Fracture ◽  
Fracture Reactivation

scholarly journals A Review of Numerical Simulation Strategies for Hydraulic Fracturing, Natural Fracture Reactivation and Induced Microseismicity Prediction

2016 ◽  
Vol 9 (1) ◽  
pp. 72-91 ◽  
Author(s):  
A.S.A. Shahid ◽  
P.A. Fokker ◽  
V. Rocca
Keyword(s):  
Numerical Simulation ◽  
Fluid Flow ◽  
Hydraulic Fracturing ◽  
Shale Gas ◽  
Deep Understanding ◽  
Natural Fracture ◽  
Extensive Literature ◽  
Coupled Problems ◽  
Modeling Approaches ◽  
Fracture Reactivation

Hydraulic fracturing, natural fracture reactivation and resulting induced microseismicity are interconnected phenomena involved in shale gas exploitation. Due to their multi-physics and their complexity, deep understanding of these phenomena as well as their mutual interaction require the adoption of coupled mechanical and fluid flow approaches. Modeling these systems is a challenging procedure as the involved processes take place on different scales of space and also require adequate multidisciplinary knowledge. An extensive literature review is presented here to provide knowledge on the modeling approaches adopted for these coupled problems. The review is intended as a guide to select effective modeling approaches for problems of different complexity.

scholarly journals A numerical investigation on the performance of hydraulic fracturing in naturally fractured gas reservoirs based on stimulated rock volume

2020 ◽  
Vol 10 (8) ◽  
pp. 3333-3345
Author(s):  
Ali Al-Rubaie ◽  
Hisham Khaled Ben Mahmud
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Natural Fracture ◽  
Shear Stresses ◽  
Individual Element ◽  
Natural Fractures ◽  
Gas Reservoirs ◽  
Stimulated Reservoir Volume ◽  
Reservoir Volume ◽  
Naturally Fractured

Abstract All reservoirs are fractured to some degree. Depending on the density, dimension, orientation and the cementation of natural fractures and the location where the hydraulic fracturing is done, preexisting natural fractures can impact hydraulic fracture propagation and the associated flow capacity. Understanding the interactions between hydraulic fracture and natural fractures is crucial in estimating fracture complexity, stimulated reservoir volume, drained reservoir volume and completion efficiency. However, because of the presence of natural fractures with diffuse penetration and different orientations, the operation is complicated in naturally fractured gas reservoirs. For this purpose, two numerical methods are proposed for simulating the hydraulic fracture in a naturally fractured gas reservoir. However, what hydraulic fracture looks like in the subsurface, especially in unconventional reservoirs, remain elusive, and many times, field observations contradict our common beliefs. In this study, the hydraulic fracture model is considered in terms of the state of tensions, on the interaction between the hydraulic fracture and the natural fracture (45°), and the effect of length and height of hydraulic fracture developed and how to distribute induced stress around the well. In order to determine the direction in which the hydraulic fracture is formed strikethrough, the finite difference method and the individual element for numerical solution are used and simulated. The results indicate that the optimum hydraulic fracture time was when the hydraulic fracture is able to connect natural fractures with large streams and connected to the well, and there is a fundamental difference between the tensile and shear opening. The analysis indicates that the growing hydraulic fracture, the tensile and shear stresses applied to the natural fracture.

scholarly journals A new slick water system for hydraulic fracturing in tight reservoir to enhance imbibition oil recovery

2021 ◽  
Vol 303 ◽  
pp. 01001
Author(s):  
Yu Haiyang ◽  
Ji Wenjuan ◽  
Luo Cheng ◽  
Lu Junkai ◽  
Yan Fei ◽  
...  
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Hydraulic Fracturing ◽  
Oil Recovery ◽  
Water System ◽  
Natural Fracture ◽  
Fracturing Fluid ◽  
The Core ◽  
Ultralow Permeability

In order to give full play to the role of imbibition of capillary force and enhance oil recovery of ultralow permeability sandstone reservoir after hydraulic fracturing, the mixed water fracture technology based on functional slick water is described and successfully applied to several wells in oilfield. The core of the technology is determination of influence factors of imbibition oil recovery, the development of new functional slick water system and optimization of volume fracturing parameters. The imbibition results show that it is significant effect of interfacial tension, wetting on imbibition oil recovery. The interfacial tension decreases by an order of magnitude, the imbibition oil recovery reduces by more than 10%. The imbibition oil recovery increases with the contact angle decreasing. The emulsifying ability has no obvious effect on imbibition oil recovery. The functional slick water system considering imbibition is developed based on the solution rheology and polymer chemistry. The system has introduced the active group and temperature resistant group into the polymer molecules. The molecular weight is controlled in 1.5 million. The viscosity is greater than 2mPa·s after shearing 2h under 170s-1 and 100℃. The interfacial tension could decrease to 10-2mN/m. The contact angle decreased from 58° to 22° and the core damage rate is less than 12%. The imbibition oil recovery could reach to 43%. The fracturing process includes slick water stage and linear gel stage. 10% 100 mesh ceramists and 8% temporary plugging agents are carried into the formation by functional slick water. 40-70 mesh ceramists are carried by linear gel. The liquid volume ratio is about 4:1 and the displacement is controlled at 10-12m3/min. The sand content and fracturing fluid volumes of single stage are 80m3 and 2500 m3 respectively. Compared with conventional fracturing, due to imbibition oil recovery, there is only 25% of the fracturing fluid flowback rate when the crude oil flew out. When the oil well is in normal production, about 50% of the fracturing fluid is not returned. It is useful to maintain the formation energy and slow down the production decline. The average cumulative production of vertical wells is greater than 2800t, and the effective period is more than 2 years. This technology overcoming the problem of high horizontal stress difference and lack of natural fracture has been successfully applied in Jidong Oilfield ultralow permeability reservoir. The successful application of this technology not only helps to promote the effective use of ultralow permeability reservoirs, but also helps to further clarify the role of imbibition recovery, energy storage and oil-water replacement mechanism.

Predicting Hydraulic Fracturing in a Carbonate Gas Reservoir in Abu Dhabi Using 1D Mechanical Earth Model: Uncertainty and Constraints

2015 ◽  
Author(s):  
Manhal Sirat ◽  
Mujahed Ahmed ◽  
Xing Zhang
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Natural Fracture ◽  
Abu Dhabi ◽  
Hydraulic Fractures ◽  
Gas Reservoir ◽  
In Situ Stresses ◽  
Tight Carbonate ◽  
Different Depths

Abstract In-situ stress state plays an important role in controlling fracture growth and containment in hydraulic fracturing managements. It is evident that the mechanical properties, existing stress regime and the natural fracture network of its reservoir rocks and the surrounding formations mainly control the geometry, size and containments of produced hydraulic fractures. Furthermore, the three principal in situ stresses' axes swap directions and magnitudes at different depths giving rise to identifying different mechanical bedrocks with corresponding stress regimes at different depths. Hence predicting the hydro-fractures can be theoretically achieved once all the above data are available. This is particularly difficult in unconventional and tight carbonate reservoirs, where heterogeneity and highly stress variation, in terms of magnitude and orientation, are expected. To optimize the field development plan (FDP) of a tight carbonate gas reservoir in Abu Dhabi, 1D Mechanical Earth Models (MEMs), involving generating the three principal in-situ stresses' profiles and mechanical property characterization with depth, have been constructed for four vertical wells. The results reveal the swap of stress magnitudes at different mechanical layers, which controls the dimension and orientation of the produced hydro-fractures. Predicted containment of the Hydro-fractures within the specific zones is likely with inevitable high uncertainty when the stress contrast between Sv, SHmax with Shmin respectively as well as Young's modulus and Poisson's Ratio variations cannot be estimated accurately. The uncertainty associated with this analysis is mainly related to the lacking of the calibration of the stress profiles of the 1D MEMs with minifrac and/or XLOT data, and both mechanical and elastic properties with rock mechanic testing results. This study investigates the uncertainty in predicting hydraulic fracture containment due to lacking such calibration, which highlights that a complete suite of data, including calibration of 1D MEMs, is crucial in hydraulic fracture treatment.

Elastoplastic constitutive model for hydraulic aperture analysis of hydro-shearing in geothermal energy development

SIMULATION ◽  
2018 ◽  
Vol 95 (9) ◽  
pp. 861-872
Author(s):  
Yong Xiao ◽  
Jianchun Guo ◽  
Hehua Wang ◽  
Lize Lu ◽  
Mengting Chen
Keyword(s):  
Shear Strength ◽  
Hydraulic Fracturing ◽  
Geothermal Energy ◽  
Energy Development ◽  
Green Energy ◽  
Shear Displacement ◽  
Natural Fracture ◽  
Roughness Coefficient ◽  
Fracture Simulation ◽  
Hydraulic Aperture

Geothermal energy is renewable, clean and green energy generated and stored in the Earth’s crust. The most important consideration for geothermal energy development in non-hydrothermal scenarios is the use of hydraulic fracturing technology to establish an effective network pathway to conduct fluid from injectors to producers. Hydraulic fracturing in geothermal wells is referred to as hydro-shearing and the aim is to improve the conductivity of natural fractures. In this paper, linear elastic constitutive relationships and shear strength of discontinuities in the pre-peak region are initially considered. Based on the dynamic frictional weakening, a proved conductive aperture and the post-peak elastoplastic constitutive models are proposed to analyze the deformation and conductivity of the natural fracture. Simulation research has shown that the joint compressive strength (JCS) mainly affects the shear displacement and hardly affects the dilation. The joint roughness coefficient (JRC) is more important for decreasing the shear strength and improves the dilation aperture. To no one’s surprise, reducing the effective normal stress is the best way for increasing the shear displacement, dilation and conductivity of the natural fracture. Almost 90% of the slip displacement and dilation occurs after fracture shear failure. This displacement not only increases the hydraulic conductivity of the fracture, but also reduces the required surface pumping pressure.

Improving the efficiency of hydraulic fracturing treatment in CBM reservoirs by stimulating the surrounding natural fracture system

2015 ◽  
Vol 55 (1) ◽  
pp. 351
Author(s):  
Alireza Keshavarz ◽  
Alexander Badalyan ◽  
Raymond Johnson ◽  
Pavel Bedrikovetski
Keyword(s):  
Hydraulic Fracturing ◽  
Mathematical Modelling ◽  
Gas Production ◽  
Natural Fracture ◽  
Productivity Index ◽  
Coal Bed ◽  
Natural Fractures ◽  
Core Flooding ◽  
Induced Fractures ◽  
Water Gas

A method is proposed for enhancing the conductivity of micro-fractures and cleats around the hydraulically induced fractures in coal bed methane reservoirs. In this technique, placing ultra-fine proppant particles in natural fractures and cleats around hydraulically induced fractures at leak-off conditions keeps the coal cleats open during water-gas production, and this consequently increases the efficiency of hydraulic fracturing treatment. Experimental and mathematical studies for the stimulation of a natural cleat system around the main hydraulic fracture are conducted. In the experimental part, core flooding tests are performed to inject a flow of suspended particles inside the natural fractures of a coal sample. By placing different particle sizes and evaluating the concentration of placed particles, an experimental coefficient is found for optimum proppant placement in which the maximum permeability is achieved after proppant placement. In the mathematical modelling study, a laboratory-based mathematical model for graded proppant placement in naturally fractured rocks around a hydraulically induced fracture is proposed. Derivations of the model include an exponential form of the pressure-permeability dependence and accounts for permeability variation in the non-stimulated zone. The explicit formulae are derived for the well productivity index by including the experimentally found coefficient. Particle placement tests resulted in an almost three-times increase in coal permeability. The laboratory-based mathematical modelling, as performed for the field conditions, shows that the proposed method yields around a six-times increase in the productivity index.

Some challenges in hydraulic fracturing of tight gas reservoirs: an experimental study

2011 ◽  
Vol 51 (1) ◽  
pp. 499 ◽  
Author(s):  
Vamegh Rasouli ◽  
Mohammad Sarmadivaleh ◽  
Amin Nabipour
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Interaction Mechanism ◽  
Natural Fracture ◽  
Gas Reservoirs ◽  
Tight Sandstone ◽  
True Triaxial ◽  
Rock Types ◽  
Interface Parameters

Hydraulic fracturing is a technique used to enhance production from low quality oil and gas reservoirs. This approach is the key technique specifically in developing unconventional reservoirs, such as tight formations and shale gas. During its propagation, the hydraulic fracture may arrive at different interfaces. The mechanical properties and bounding quality of the interface as well as insitu stresses are among the most significant parameters that determine the interaction mechanism, i.e. whether the hydraulic fracture stops, crosses or experiences an offset upon its arrival at the interface. The interface could be a natural fracture, an interbed, layering or any other weakness feature. In addition to the interface parameters, the rock types of the two sides of the interface may affect the interaction mechanism. To study the interaction mechanism, hydraulic fracturing experiments were conducted using a true triaxial stress cell on two cube samples of 15 cm. Sample I had a sandstone block in the middle surrounded by mortar, whereas in sample II the location of mortar and tight sandstone blocks were changed. The results indicated that besides the effect of the far field stress magnitudes, the heterogeneity of the formation texture and interface properties can have a dominant effect in propagation characteristics of an induced fracture.

Development of a new approach for hydraulic fracturing in tight sand with pre-existing natural fractures

2016 ◽  
Vol 56 (1) ◽  
pp. 225 ◽  
Author(s):  
Kunakorn Pokalai ◽  
David Kulikowski ◽  
Raymond L. Johnson ◽  
Manouchehr Haghighi ◽  
Dennis Cooke
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
High Stress ◽  
Gas Production ◽  
Natural Fracture ◽  
Rock Properties ◽  
Fracture Plane ◽  
Natural Fractures ◽  
Geomechanical Model ◽  
Well Design

Hydraulic fracturing in tight gas reservoirs has been performed in the Cooper Basin for decades in reservoirs containing high stress and pre-existing natural fractures, especially near faults. The hydraulic fracture is affected by factors such as tortuosity, high entry pressures, and the rock fabric including natural fractures. These factors cause fracture plane rotation and complexities, leading to fracture disconnection or reduced proppant placement during the treatment. In this paper, rock properties are estimated for a targeted formation using well logs to create a geomechanical model. Natural fracture and stress azimuths within the interval were interpreted from borehole image logs. The image log interpretations inferred that fissures are oriented 30–60° relative to the maximum horizontal stress. Next, diagnostic fracture injection test (DFIT) data was used with the poro-elastic stress equations to predict tectonic strains. Finally, the geomechanical model was history-matched with a planar 3D hydraulic fracturing simulator, and gave more insight into fracture propagation in an environment of pre-existing natural fractures. The natural fracture azimuths and calibrated geomechanical model are input into a framework to evaluate varying scenarios that might result based on a vertical or inclined well design. A well design is proposed based on the natural fracture orientation relative to the hydraulic fracture that minimises complexity to optimise proppant placement. In addition, further models and diagnostics are proposed to aid predicting the hydraulically induced fracture geometry, its impact on gas production, and optimising wellbore trajectory to positively interact with pre-existing natural fractures.

Numerical Simulation on Propagation Mechanism of Hydraulic Fracture in Fractured Rockmass

2014 ◽  
Vol 488-489 ◽  
pp. 417-420 ◽  
Author(s):  
Xiao Xi Men ◽  
C.A. Tang ◽  
Zhi Hui Han
Keyword(s):  
Hydraulic Fracturing ◽  
Fracture Initiation ◽  
Coupling Model ◽  
Natural Fracture ◽  
Tensile Fracture ◽  
Propagation Mechanism ◽  
Initiation And Propagation ◽  
Fracturing Process ◽  
Two Factors ◽  
Seepage Characteristics

Hydraulic fracturing process in fractured rockmass which with an existing single natural fracture at its various conditions: its different angles and different lengths was simulated by using RFPA2D(2.0)-Flow version which adopts the finite element method and considers the heterogeneous characteristics of rock in meso-scale, creates seepage-stress-failure coupling model. The effect tendency of natural fractures angle and length on the seepage characteristics of fractured rockmass was given through the description of tensile fracture initiation and propagation in the rock specimens. The simulation results show that the effect of these two factors on fractures initiation, propagation and rockmass stability under the hydraulic fracturing could be remarkable.

Sign in / Sign up

Export Citation Format

Share Document