Characterisation of the steel concrete interface submitted to chloride-induced-corrosion

2012 ◽  
Vol 64 (3) ◽  
pp. 185-194 ◽  
Author(s):  
V. L'Hostis ◽  
E. Amblard ◽  
W. Guillot ◽  
C. Paris ◽  
L. Bellot-Gurlet
Keyword(s):  
Chloride Induced Corrosion ◽  
Concrete Interface

scholarly journals The effect of the steel–concrete interface on chloride-induced corrosion initiation in concrete: a critical review by RILEM TC 262-SCI

2019 ◽  
Vol 52 (4) ◽  
Author(s):  
Ueli M. Angst ◽  
Mette R. Geiker ◽  
Maria Cruz Alonso ◽  
Rob Polder ◽  
O. Burkan Isgor ◽  
...  
Keyword(s):  
Critical Review ◽  
Corrosion Initiation ◽  
Chloride Induced Corrosion ◽  
Concrete Interface

scholarly journals Experimental Characterization of the FRCM-Concrete Interface Bond Behavior Assisted by Digital Image Correlation

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1154
Author(s):  
Dario De Domenico ◽  
Antonino Quattrocchi ◽  
Damiano Alizzio ◽  
Roberto Montanini ◽  
Santi Urso ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Mechanical Tests ◽  
Image Correlation ◽  
Front Face ◽  
Full Field ◽  
Bond Behavior ◽  
Externally Bonded ◽  
Strengthening Technique ◽  
Concrete Interface

Digital Image Correlation (DIC) provides measurements without disturbing the specimen, which is a major advantage over contact methods. Additionally, DIC techniques provide full-field maps of response quantities like strains and displacements, unlike traditional methods that are limited to a local investigation. In this work, an experimental application of DIC is presented to investigate a problem of relevant interest in the civil engineering field, namely the interface behavior between externally bonded fabric reinforced cementitious mortar (FRCM) sheets and concrete substrate. This represents a widespread strengthening technique of existing reinforced concrete structures, but its effectiveness is strongly related to the bond behavior between composite fabric and underlying concrete. To investigate this phenomenon, a set of notched concrete beams are realized, reinforced with FRCM sheets on the bottom face, subsequently cured in different environmental conditions (humidity and temperature) and finally tested up to failure under three-point bending. Mechanical tests are carried out vis-à-vis DIC measurements using two distinct cameras simultaneously, one focused on the concrete front face and another focused on the FRCM-concrete interface. This experimental setup makes it possible to interpret the mechanical behavior and failure mode of the specimens not only from a traditional macroscopic viewpoint but also under a local perspective concerning the evolution of the strain distribution at the FRCM-concrete interface obtained by DIC in the pre- and postcracking phase.

Shear-friction behavior of concrete-to-concrete interface under direct shear load

2021 ◽  
Vol 238 ◽  
pp. 112211
Author(s):  
Jin Xia ◽  
Kuang-yi Shan ◽  
Xiao-hui Wu ◽  
Run-li Gan ◽  
Wei-liang Jin
Keyword(s):  
Shear Load ◽  
Direct Shear ◽  
Friction Behavior ◽  
Shear Friction ◽  
Concrete Interface

scholarly journals Reinforced Concrete Bridge Deck Model Considering Delayed Exposure to Chlorides

2019 ◽  
Author(s):  
Petr Konečný ◽  
Petr Lehner ◽  
David Pustka
Keyword(s):  
Reinforced Concrete ◽  
Bridge Deck ◽  
Concrete Bridge ◽  
Reinforced Concrete Bridge ◽  
Corrosion Initiation ◽  
Chloride Induced Corrosion ◽  
Concrete Quality ◽  
Concrete Type ◽  
Concrete Bridge Deck ◽  
Delayed Exposure

The paper is focused on the model of the effect of delayed chloride exposure on the chloride induced corrosion initiation on ideal reinforced concrete bridge. The Finite Element-based numerical model is applied. The effect of concrete quality is expressed in the form of time dependent diffusion coefficient in order to evaluate the effect of concrete type as well as the effect of aging. The influence of extended chloride exposure on the corrosion initiation is introduced.

Sign in / Sign up

Export Citation Format

Share Document