Osseointegration of 3D printed microalloyed CoCr implants-Addition of 0.04% Zr to CoCr does not alter bone material properties

2018 ◽  
Vol 106 (6) ◽  
pp. 1655-1663 ◽  
Author(s):  
Furqan A. Shah ◽  
Edvin Jergéus ◽  
Akihiko Chiba ◽  
Anders Palmquist
Keyword(s):  
Material Properties ◽  
Bone Material ◽  
Bone Material Properties ◽  
3D Printed

Bone material properties as measured by Reference Point Indentation are low in subjects with acromegaly

2016 ◽  
Author(s):  
Frank Malgo ◽  
Neveen A T Hamdy ◽  
Alberto M Pereira ◽  
Nienke R Biermasz ◽  
Natasha M Appelman-Dijkstra
Keyword(s):  
Material Properties ◽  
Reference Point ◽  
Bone Material ◽  
Bone Material Properties ◽  
Reference Point Indentation

scholarly journals Developments in Modelling Bone Screwing

2020 ◽  
Vol 6 (3) ◽  
pp. 111-114
Author(s):  
Jack Wilkie ◽  
Paul D. Docherty ◽  
Knut Möller
Keyword(s):  
Material Properties ◽  
Frictional Coefficient ◽  
Viscous Friction ◽  
Model Parameters ◽  
General Shape ◽  
Bone Material ◽  
Bone Material Properties ◽  
Modelling Methodology ◽  
Recorded Data ◽  
Friction Models

AbstractINTRODUCTION: A torque-rotation model of the bone-screwing process has been proposed. Identification of model parameters using recorded data could potentially be used to determine the material properties of bone. These properties can then be used to recommend tightening torques to avoid over or under-tightening of bone screws. This paper improves an existing model to formulate it in terms of material properties and remove some assumptions. METHOD: The modelling methodology considers a critical torque, which is required to overcome friction and advance the screw into the bone. Below this torque the screw may rotate with elastic deformation of the bone tissue, and above this the screw moves relative to the bone, and the speed is governed by a speed-torque model of the operator’s hand. The model is formulated in terms of elastic modulus, ultimite tensile strength, and frictional coefficient of the bone and the geometry of the screw and hole. RESULTS: The model output shows the speed decreasing and torque increasing as the screw advances into the bone, due to increasing resistance. The general shape of the torque and speed follow the input effort. Compared with the existing model, this model removes the assumption of viscous friction, models the increase in friction as the screw advances into the bone, and is directly in terms of the bone material properties. CONCLUSION: The model presented makes significant improvements on the existing model. However it is intended for use in parameter identification, which was not evaluated here. Further simulation and experimental validation is required to establish the accuracy and fitness of this model for identifying bone material properties.

scholarly journals Impact microindentation assesses cortical bone material properties in humans

Bone Reports ◽  
2020 ◽  
Vol 13 ◽  
pp. 100395
Author(s):  
Stamatia Rokidi ◽  
Natalie Bravenboer ◽  
Sonja Gamsjaeger ◽  
Pascale Chavassieux ◽  
Jochen Zwerina ◽  
...  
Keyword(s):  
Cortical Bone ◽  
Material Properties ◽  
Bone Material ◽  
Bone Material Properties ◽  
Impact Microindentation

scholarly journals Bone cell-independent benefits of raloxifene on the skeleton: A novel mechanism for improving bone material properties

Bone ◽  
2014 ◽  
Vol 61 ◽  
pp. 191-200 ◽  
Author(s):  
Maxime A. Gallant ◽  
Drew M. Brown ◽  
Max Hammond ◽  
Joseph M. Wallace ◽  
Jiang Du ◽  
...  
Keyword(s):  
Material Properties ◽  
Bone Cell ◽  
Bone Material ◽  
Bone Material Properties

scholarly journals Effects of alendronate and risedronate on bone material properties in actively forming trabecular bone surfaces

2012 ◽  
Vol 27 (5) ◽  
pp. 995-1003 ◽  
Author(s):  
Birgit Hofstetter ◽  
Sonja Gamsjaeger ◽  
Roger J Phipps ◽  
Robert R Recker ◽  
Frank H Ebetino ◽  
...  
Keyword(s):  
Trabecular Bone ◽  
Material Properties ◽  
Bone Material ◽  
Bone Material Properties
Sign in / Sign up

Export Citation Format

Share Document