scholarly journals Hydrostatic pressure in combination with topographical cues affects the fate of bone marrow-derived human mesenchymal stem cells for bone tissue regeneration

2017 ◽  
Vol 106 (3) ◽  
pp. 629-640 ◽  
Author(s):  
Yvonne Reinwald ◽  
Alicia J. El Haj
Keyword(s):  
Stem Cells ◽  
Bone Marrow ◽  
Mesenchymal Stem Cells ◽  
Hydrostatic Pressure ◽  
Bone Tissue ◽  
Tissue Regeneration ◽  
Human Mesenchymal Stem Cells ◽  
Bone Tissue Regeneration ◽  
Topographical Cues

scholarly journals 3D Printed SiOC(N) Ceramic Scaffolds for Bone Tissue Regeneration: Improved Osteogenic Differentiation of Human Bone Marrow-Derived Mesenchymal Stem Cells

2021 ◽  
Vol 22 (24) ◽  
pp. 13676
Author(s):  
Yuejiao Yang ◽  
Apoorv Kulkarni ◽  
Gian Domenico Soraru ◽  
Joshua M. Pearce ◽  
Antonella Motta
Keyword(s):  
Stem Cells ◽  
Mesenchymal Stem Cells ◽  
3D Printing ◽  
Pore Size ◽  
Osteogenic Differentiation ◽  
Bone Tissue ◽  
Low Cost ◽  
Human Mesenchymal Stem Cells ◽  
Bone Tissue Regeneration ◽  
Gene Expressions

Bone tissue engineering has developed significantly in recent years as there has been increasing demand for bone substitutes due to trauma, cancer, arthritis, and infections. The scaffolds for bone regeneration need to be mechanically stable and have a 3D architecture with interconnected pores. With the advances in additive manufacturing technology, these requirements can be fulfilled by 3D printing scaffolds with controlled geometry and porosity using a low-cost multistep process. The scaffolds, however, must also be bioactive to promote the environment for the cells to regenerate into bone tissue. To determine if a low-cost 3D printing method for bespoke SiOC(N) porous structures can regenerate bone, these structures were tested for osteointegration potential by using human mesenchymal stem cells (hMSCs). This includes checking the general biocompatibilities under the osteogenic differentiation environment (cell proliferation and metabolism). Moreover, cell morphology was observed by confocal microscopy, and gene expressions on typical osteogenic markers at different stages for bone formation were determined by real-time PCR. The results of the study showed the pore size of the scaffolds had a significant impact on differentiation. A certain range of pore size could stimulate osteogenic differentiation, thus promoting bone regrowth and regeneration.

scholarly journals Mesenchymal Stem Cells in Bone Tissue Regeneration and Application to Bone Healing

2009 ◽  
Vol 78 (4) ◽  
pp. 635-642 ◽  
Author(s):  
Michal Crha ◽  
Alois Nečas ◽  
Robert Srnec ◽  
Jan Janovec ◽  
Ladislav Stehlík ◽  
...  
Keyword(s):  
Stem Cells ◽  
Mesenchymal Stem Cells ◽  
Bone Tissue ◽  
Tissue Regeneration ◽  
Bone Healing ◽  
Experimental Studies ◽  
Bone Defects ◽  
Bone Tissue Regeneration ◽  
Bone Lesions ◽  
Tumour Resection

This synoptic study gives a concise overview of current knowledge of bone healing, the role of mesenchymal stem cells in bone tissue regeneration and contemporary possibilities of supporting regeneration of damaged bone. Attention of research concerning the healing of fractures with extensive loss of bone tissue following trauma, the treatment of belatedly healing or non-healing fractures or the healing of segmental bone defects following tumour resection, is focused on development of three-dimensional scaffolds planted with mesenchymal stem cells that might be used for reconstruction of such large bone lesions. Presented are possibilities of transplantation of mesenchymal stem cells combined with biomaterials into bone defects, including the results of our own experimental studies dealing with the use of stem cells in the treatment of damaged tissues of the musculoskeletal system in animal models.

scholarly journals 3D Printed SiOC(N) Ceramic Scaffolds for Bone Tissue Regeneration: Improved Osteogenic Differentiation of Human Bone Marrow‐Derived Mesenchymal Stem Cells

2021 ◽  
Author(s):  
Yuejiao Yang ◽  
Apoorv Kulkarni ◽  
Gian Domenico Soraru ◽  
Joshua M Pearce ◽  
Antonella Motta
Keyword(s):  
Stem Cells ◽  
Mesenchymal Stem Cells ◽  
3D Printing ◽  
Pore Size ◽  
Osteogenic Differentiation ◽  
Bone Tissue ◽  
Low Cost ◽  
Human Mesenchymal Stem Cells ◽  
Bone Tissue Regeneration ◽  
Gene Expressions

Bone tissue engineering has developed significantly in recent years as the increasing demand for bone substitutes due to trauma, cancer, arthritis, and infections. The scaffolds for bone regeneration need to be mechanically stable and have a 3D architecture with interconnected pores. With the advances in additive manufacturing technology, these requirements can be fulfilled by 3D printing scaffolds with controlled geometry and porosity using a low-cost multistep process. The scaffolds, however, must also be bioactive to promote the environment for the cells to regenerate into bone tissue. To determine if a low-cost 3D printing method for bespoke SiOC(N) porous structures can regenerate bone these structures were tested for osteointegration potential by using human mesenchymal stem cells (hMSCs). This includes checking the general biocompatibilities under the osteogenic differentiation environment (cell proliferation and metabolism). Moreover, cell morphology was observed by confocal microscopy and gene expressions on typical osteogenic markers at different stages for bone formation were determined by real-time PCR. The results of the study showed the pore size of the scaffolds had a significant impact on differentiation. A certain range of pore size could stimulate osteogenic differentiation, thus promoting bone regrowth and regeneration.

Sign in / Sign up

Export Citation Format

Share Document