Mechanical properties and biomechanical compatibility of porous titanium for dental implants

1985 ◽  
Vol 19 (6) ◽  
pp. 699-713 ◽  
Author(s):  
Kenzo Asaoka ◽  
Norihiko Kuwayama ◽  
Osamu Okuno ◽  
Ishi Miura
Keyword(s):  
Mechanical Properties ◽  
Dental Implants ◽  
Porous Titanium ◽  
Biomechanical Compatibility

Preparation of Porous Titanium Dental Implant by 3D Printing/Composite Coating and Its Biomechanical Properties and Flexural Strength

2020 ◽  
Vol 12 (10) ◽  
pp. 1492-1501
Author(s):  
Chengxue Yang ◽  
Zhengwen Yu ◽  
Yuanzhu Long ◽  
Lin Chen
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Flexural Strength ◽  
Dental Implants ◽  
Composite Coating ◽  
Test Specimen ◽  
Biomechanical Properties ◽  
Porous Titanium ◽  
Nano Coating ◽  
Flexural Resistance

Dental implants have been widely used in clinical practice. The 3D modeling software was used to design threedimensional (3D) models (in the shapes of long strips, discs, and screws), i.e., the Ti2.6Al1.2 V0.42 specimens. Meanwhile, the implant material was electrochemically precipitated, and a layer of chitosan nano-coating was added to the surface. To test the bone-binding ability and planting success rate of the material, the mechanical properties of the specimens with different porosity (0%∼70%) were firstly analyzed by the three-point bending method. Then, the screw-shaped titanium alloy specimens were divided into the solid group, the solid coating group, the solid 30% group, the coating 30% group, the solid 50% group, and the coating 50% group. The MC3T3-E1 cells were cultured, and the in vitro biological properties of the specimens were tested from different angles. The biomechanical properties and flexural strength of screw-shaped titanium alloy specimens in different groups were tested by using a universal testing machine. In the experiment, the prepared dental implants had the complete surface, uniform pore distribution, dense coating distribution, and less overall cracks. The elastic gradient of porous titanium specimens would decrease due to the increase of porosity. The cell activity of the test specimen was higher, and the percentage of viable cells exceeded 80%. The MTT test confirmed that the pores of the test specimen could promote the increase of MTT value (P < 0.05), and the test specimen/composite coating had higher ALP levels compared with the test pieces with no surface treatments (P < 0.05). In biomechanical properties and flexural strength tests, the increase of pores increased the biomechanical properties (P < 0.05) and decreased the flexural resistance (P < 0.05), while the increase of coating decreased the biomechanical properties and increased the flexural resistance (P < 0.05). The porous titanium alloy specimens were successfully prepared, and the chitosan-based composite coating was applied. The material was non-toxic, which was beneficial to cell proliferation and had good mechanical properties, thereby contributing to the growth of new bone.

Mechanical Properties of Porous Titanium Structure Fabricated by Investment Casting with Pressurization/Depressurization System

2014 ◽  
Vol 52 (3) ◽  
pp. 203-209 ◽  
Author(s):  
San Kang ◽  
Ji Woon Lee ◽  
Soong Keun Hyun ◽  
Byong Pil Lee ◽  
Myoung Gyun Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Investment Casting ◽  
Porous Titanium ◽  
Titanium Structure

Osseointegration of dental implants in extraction sockets preserved with porous titanium granules - an experimental study

2012 ◽  
Vol 25 (2) ◽  
pp. e100-e108 ◽  
Author(s):  
Anders Verket ◽  
Ståle P. Lyngstadaas ◽  
Hans J. Rønold ◽  
Johan C. Wohlfahrt
Keyword(s):  
Experimental Study ◽  
Dental Implants ◽  
Porous Titanium

scholarly journals Effects of Sintering Behaviors on Dimensional Accuracy, Surface Quality, and Mechanical Properties of Stereolithography-printed 3Y-ZrO2 Ceramics

2021 ◽  
Author(s):  
Cheng Zhang ◽  
Zhaoliang Jiang ◽  
Li Zhao ◽  
Weiwei Guo ◽  
Chengpeng Zhang
Keyword(s):  
Mechanical Properties ◽  
Dental Implants ◽  
Surface Quality ◽  
Dimensional Accuracy ◽  
Scanning Speed ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Air Atmosphere ◽  
Length Width ◽  
Technical Guide

Abstract Sintering process is essential to acquire the final components by stereolithography (SLA), which is a promising additive manufacturing technology for the fabrication of complex, custom-designed dental implants. 3Y-ZrO2 ceramics at different sintering behaviors in air atmosphere were successfully obtained in this study. Firstly, the curing properties of homemade pastes were studied, and the penetration depth and critical exposure of the pastes were calculated as 17.2 μm and 4.80 mJ/cm2, respectively. The green ceramic parts were performed at 154 mW laser power and 6000 mm/s scanning speed. Then, the dimensional accuracy, surface quality, and mechanical properties of 3Y-ZrO2 ceramics were investigated. The shrinkages of length, width, and height were 26%~27 %, 30%~31 %, and 27%~33 % in sintered ceramics, respectively. The Ra values of XOY, YOZ, and XOZ surfaces showed an anisotropic feature, and they were smallest as 0.52 μm, 2.40 μm, and 2.46 μm, respectively. Meanwhile, the mechanical properties presented a similar trend that they grew first and then dropped at various sintering behaviors. The optimal parameters were 1500 ℃, 60 min, and 4 ℃/min, and the maximum relative density of 96.18 %, Vickers hardness of 12.45 GPa, and fracture toughness of 6.35 MPa·m1/2 were achieved. Finally, the X-ray diffraction (XRD) and energy-dispersive spectroscopy (EDS) analysis demonstrated that no change was observed in crystal transformation and phase composition, and the organic was completely removed in sintered ceramics. This research is expected to provide a technical guide for the fabrication of ceramics for dental implants using SLA technique.

scholarly journals Experimental Investigation into the Effect of Surface Roughness and Mechanical Properties of 3D-Printed Titanium Ti-64 ELI after Heat Treatment

2021 ◽  
Author(s):  
Lebogang Lebea ◽  
Harry M Ngwangwa ◽  
Dawood Desai ◽  
Fuluphelo Nemavhola
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Dental Implants ◽  
Dental Implant ◽  
Complex Geometry ◽  
Poor Performance ◽  
Vital Role ◽  
Ultimate Tensile Stress ◽  
3D Printed ◽  
Effect Of Surface

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Space-holder effect on designing pore structure and determining mechanical properties in porous titanium

2014 ◽  
Vol 57 ◽  
pp. 712-718 ◽  
Author(s):  
Byounggab Lee ◽  
Taekyung Lee ◽  
Yongmoon Lee ◽  
Dong Jun Lee ◽  
Jiwon Jeong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Pore Structure ◽  
Porous Titanium ◽  
Space Holder

Tantalum as a Novel Biomaterial for Bone Implant: A Literature Review

2021 ◽  
Vol 52 ◽  
pp. 55-65
Author(s):  
Ivan Putrantyo ◽  
Nikhit Anilbhai ◽  
Revati Vanjani ◽  
Brigita De Vega
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Dental Implants ◽  
Bulk Material ◽  
High Melting Point ◽  
Design Modification ◽  
Bone Implant ◽  
Specific Strength ◽  
Metallic Implants ◽  
Tantalum Coatings

Titanium (Ti) has been used in metallic implants since the 1950s due to various biocompatible and mechanical properties. However, due to its high Young’s modulus, it has been modified over the years in order to produce a better biomaterial. Tantalum (Ta) has recently emerged as a new potential biomaterial for bone and dental implants. It has been reported to have better corrosion resistance and osteo-regenerative properties as compared to Ti alloys which are most widely used in the bone-implant industry. Currently, Tantalum cannot be widely used yet due to its limited availability, high melting point, and high-cost production. This review paper discusses various manufacturing methods of Tantalum alloys, including conventional and additive manufacturing and also discusses their drawbacks and shortcomings. Recent research includes surface modification of various metals using Tantalum coatings in order to combine bulk material properties of different materials and the porous surface properties of Tantalum. Design modification also plays a crucial role in controlling bulk properties. The porous design does provide a lower density, wider surface area, and more immense specific strength. In addition to improved mechanical properties, a porous design could also escalate the material's biological and permeability properties. With current advancement in additive manufacturing technology, difficulties in processing Tantalum could be resolved. Therefore, Tantalum should be considered as a serious candidate material for future bone and dental implants.

scholarly journals Enhancement of Bone Ingrowth into a Porous Titanium Structure to Improve Osseointegration of Dental Implants: A Pilot Study in the Canine Model

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3061 ◽  
Author(s):  
Ji-Youn Hong ◽  
Seok-Yeong Ko ◽  
Wonsik Lee ◽  
Yun-Young Chang ◽  
Su-Hwan Kim ◽  
...  
Keyword(s):  
Porous Structure ◽  
Dental Implants ◽  
Bone Growth ◽  
Bone Ingrowth ◽  
Test Group ◽  
Porous Titanium ◽  
Control Group ◽  
Machined Surface ◽  
Significant Difference ◽  
Titanium Structure

A porous titanium structure was suggested to improve implant stability in the early healing period or in poor bone quality. This study investigated the effect of a porous structure on the osseointegration of dental implants. A total of 28 implants (14 implants in each group) were placed in the posterior mandibles of four beagle dogs at 3 months after extraction. The control group included machined surface implants with an external implant–abutment connection, whereas test group implants had a porous titanium structure added to the apical portion. Resonance frequency analysis (RFA); removal torque values (RTV); and surface topographic and histometric parameters including bone-to-implant contact length and ratio, inter-thread bone area and ratio in total, and the coronal and apical parts of the implants were measured after 4 weeks of healing. RTV showed a significant difference between the groups after 4 weeks of healing (p = 0.032), whereas no difference was observed in RFA. In the test group, surface topography showed bone tissue integrated into the porous structures. In the apical part of the test group, all the histometric parameters exhibited significant increases compared to the control group. Within the limitations of this study, enhanced bone growth into the porous structure was achieved, which consequently improved osseointegration of the implant.

Sign in / Sign up

Export Citation Format

Share Document