The onset of Rayleigh–Bénard convection and heat transfer under two‐frequency rotation modulation

Heat Transfer ◽  
2021 ◽  
Author(s):  
Ansa Mathew ◽  
S. Pranesh
Keyword(s):  
Heat Transfer ◽  
Convection And Heat Transfer ◽  
Bénard Convection ◽  
Benard Convection ◽  
Rayleigh Benard Convection ◽  
Rayleigh Benard

scholarly journals Heat transfer in rotating Rayleigh–Bénard convection with rough plates

2017 ◽  
Vol 830 ◽  
Author(s):  
Pranav Joshi ◽  
Hadi Rajaei ◽  
Rudie P. J. Kunnen ◽  
Herman J. H. Clercx
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Ekman Layer ◽  
Ekman Pumping ◽  
Ekman Boundary Layer ◽  
Bénard Convection ◽  
Roughness Elements ◽  
Benard Convection ◽  
Rayleigh Benard Convection ◽  
Rayleigh Benard

This experimental study focuses on the effect of horizontal boundaries with pyramid-shaped roughness elements on the heat transfer in rotating Rayleigh–Bénard convection. It is shown that the Ekman pumping mechanism, which is responsible for the heat transfer enhancement under rotation in the case of smooth top and bottom surfaces, is unaffected by the roughness as long as the Ekman layer thickness $\unicode[STIX]{x1D6FF}_{E}$ is significantly larger than the roughness height $k$. As the rotation rate increases, and thus $\unicode[STIX]{x1D6FF}_{E}$ decreases, the roughness elements penetrate the radially inward flow in the interior of the Ekman boundary layer that feeds the columnar Ekman vortices. This perturbation generates additional thermal disturbances which are found to increase the heat transfer efficiency even further. However, when $\unicode[STIX]{x1D6FF}_{E}\approx k$, the Ekman boundary layer is strongly perturbed by the roughness elements and the Ekman pumping mechanism is suppressed. The results suggest that the Ekman pumping is re-established for $\unicode[STIX]{x1D6FF}_{E}\ll k$ as the faces of the pyramidal roughness elements then act locally as a sloping boundary on which an Ekman layer can be formed.

scholarly journals Heat transfer mechanisms in bubbly Rayleigh-Bénard convection

2009 ◽  
Vol 80 (2) ◽  
Author(s):  
Paolo Oresta ◽  
Roberto Verzicco ◽  
Detlef Lohse ◽  
Andrea Prosperetti
Keyword(s):  
Heat Transfer ◽  
Bénard Convection ◽  
Benard Convection ◽  
Rayleigh Benard Convection ◽  
Rayleigh Benard ◽  
Transfer Mechanisms

scholarly journals Mixed insulating and conducting thermal boundary conditions in Rayleigh–Bénard convection

2017 ◽  
Vol 835 ◽  
pp. 491-511 ◽  
Author(s):  
Dennis Bakhuis ◽  
Rodolfo Ostilla-Mónico ◽  
Erwin P. van der Poel ◽  
Roberto Verzicco ◽  
Detlef Lohse
Keyword(s):  
Heat Transfer ◽  
Boundary Conditions ◽  
Heat Transport ◽  
Bottom Plate ◽  
Bulk Temperature ◽  
Stripe Pattern ◽  
Bénard Convection ◽  
Benard Convection ◽  
Rayleigh Benard Convection ◽  
Rayleigh Benard

A series of direct numerical simulations of Rayleigh–Bénard convection, the flow in a fluid layer heated from below and cooled from above, were conducted to investigate the effect of mixed insulating and conducting boundary conditions on convective flows. Rayleigh numbers between $Ra=10^{7}$ and $Ra=10^{9}$ were considered, for Prandtl numbers $\mathit{Pr}=1$ and $\mathit{Pr}=10$. The bottom plate was divided into patterns of conducting and insulating stripes. The size ratio between these stripes was fixed to unity and the total number of stripes was varied. Global quantities, such as the heat transport and average bulk temperature, and local quantities, such as the temperature just below the insulating boundary wall, were investigated. For the case with the top boundary divided into two halves, one conducting and one insulating, the heat transfer was found to be approximately two-thirds of that for the fully conducting case. Increasing the pattern frequency increased the heat transfer, which asymptotically approached the fully conducting case, even if only half of the surface is conducting. Fourier analysis of the temperature field revealed that the imprinted pattern of the plates is diffused in the thermal boundary layers, and cannot be detected in the bulk. With conducting–insulating patterns on both plates, the trends previously described were similar; however, the half-and-half division led to a heat transfer of about a half of that for the fully conducting case instead of two-thirds. The effect of the ratio of conducting and insulating areas was also analysed, and it was found that, even for systems with a top plate with only 25 % conducting surface, heat transport of 60 % of the fully conducting case can be seen. Changing the one-dimensional stripe pattern to a two-dimensional chequerboard tessellation does not result in a significantly different response of the system.

Sign in / Sign up

Export Citation Format

Share Document