In Situ Investigation of Two-Phase Flow Patterns in Flow Fields of PEFC’s Using Neutron Radiography

Fuel Cells ◽  
2002 ◽  
Vol 2 (2) ◽  
pp. 92-98 ◽  
Author(s):  
A.B. Geiger ◽  
A. Tsukada ◽  
E. Lehmann ◽  
P. Vontobel ◽  
A. Wokaun ◽  
...  
Keyword(s):  
Two Phase Flow ◽  
Neutron Radiography ◽  
Flow Fields ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
In Situ Investigation

scholarly journals Two-Phase Flow Mass Transfer Analysis of Airlift Pump for Aquaculture Applications

Fluids ◽  
2021 ◽  
Vol 6 (6) ◽  
pp. 226
Author(s):  
Rashal Abed ◽  
Mohamed M. Hussein ◽  
Wael H. Ahmed ◽  
Sherif Abdou
Keyword(s):  
Mass Transfer ◽  
Oxygen Transfer ◽  
Transfer Rate ◽  
Two Phase Flow ◽  
Oxygen Transfer Rate ◽  
Flow Patterns ◽  
Oxygen Mass Transfer ◽  
Phase Flow ◽  
Two Phase ◽  
Airlift Pump

Airlift pumps can be used in the aquaculture industry to provide aeration while concurrently moving water utilizing the dynamics of two-phase flow in the pump riser. The oxygen mass transfer that occurs from the injected compressed air to the water in the aquaculture systems can be experimentally investigated to determine the pump aeration capabilities. The objective of this study is to evaluate the effects of various airflow rates as well as the injection methods on the oxygen transfer rate within a dual injector airlift pump system. Experiments were conducted using an airlift pump connected to a vertical pump riser within a recirculating system. Both two-phase flow patterns and the void fraction measurements were used to evaluate the dissolved oxygen mass transfer mechanism through the airlift pump. A dissolved oxygen (DO) sensor was used to determine the DO levels within the airlift pumping system at different operating conditions required by the pump. Flow visualization imaging and particle image velocimetry (PIV) measurements were performed in order to better understand the effects of the two-phase flow patterns on the aeration performance. It was found that the radial injection method reached the saturation point faster at lower airflow rates, whereas the axial method performed better as the airflow rates were increased. The standard oxygen transfer rate (SOTR) and standard aeration efficiency (SAE) were calculated and were found to strongly depend on the injection method as well as the two-phase flow patterns in the pump riser.

Dynamic mesh simulation on the effect of sloshing on concurrent two-phase flow fields for two-dimensionally packed columns simulations

Cryogenics ◽  
2021 ◽  
Vol 113 ◽  
pp. 103231
Author(s):  
Lingya Meng ◽  
Chongzheng Sun ◽  
Mengxian Zhang ◽  
Hui Han ◽  
Yuxing Li
Keyword(s):  
Two Phase Flow ◽  
Flow Fields ◽  
Packed Columns ◽  
Dynamic Mesh ◽  
Phase Flow ◽  
Two Phase

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2003 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase ◽  
Micro Channels

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406 × 2.032 mm cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal that the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Annual flow is identified as the dominant flow pattern for conditions relevant to two-phase micro-channel heat sinks, and forms the basis for development of a theoretical model for both pressure drop and heat transfer in micro-channels. Features unique to two-phase micro-channel flow, such as laminar liquid and gas flows, smooth liquid-gas interface, and strong entrainment and deposition effects are incorporated into the model. The model shows good agreement with experimental data for water-cooled heat sinks.

Sign in / Sign up

Export Citation Format

Share Document