Postfire mechanical properties of Galfan‐coated steel cables

2020 ◽  
Vol 44 (7) ◽  
pp. 909-922
Author(s):  
Guojun Sun ◽  
Xiaohui Li ◽  
Jinzhi Wu
Keyword(s):  
Mechanical Properties ◽  
Coated Steel ◽  
Steel Cables

Mechanical properties of Galfan-coated steel cables at elevated temperatures

2019 ◽  
Vol 155 ◽  
pp. 331-341 ◽  
Author(s):  
Guojun Sun ◽  
Xiaohui Li ◽  
Suduo Xue ◽  
Ronghua Chen
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Coated Steel ◽  
Steel Cables

Comparison of Porosity Evaluation Methods Using the Example of Dissimilar Metal Joints

2019 ◽  
Vol 822 ◽  
pp. 129-134
Author(s):  
Dmitry Kurushkin ◽  
Igor Mushnikov ◽  
Evgenii Rylkov ◽  
Fedor Y. Isupov ◽  
Oleg Panchenko ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Evaluation Methods ◽  
Coated Steel ◽  
Dissimilar Metal ◽  
Relative Porosity ◽  
Zinc Coated Steel ◽  
3D Methods ◽  
2D And 3D ◽  
Measured Volume

Welded metal porosity significantly influences the mechanical properties of dissimilar metal joints. In this study, the comparison of porosity evaluation methods was held using the sample of welded-brazed zinc coated steel and Al-Mg-alloy plates joint. Relative porosity was measured through cross-sections’ images area analysis, as well as it was evaluated through 3D-fitting of spotted on these images pores. Area and size of pores was measured, volume and distribution were evaluated. It was found that relative porosity values estimated by 2D and 3D methods are equal.

Local Mechanical Properties of Zinc-Iron Coated Steel Sheets by Depth-Sensing Indentation

2018 ◽  
Vol 784 ◽  
pp. 153-158
Author(s):  
Ľubomír Ambriško ◽  
Ladislav Pešek
Keyword(s):  
Mechanical Properties ◽  
Iron Concentration ◽  
Intermetallic Phases ◽  
Coated Steel ◽  
If Steel ◽  
Depth Sensing ◽  
Steel Sheets ◽  
Coating Surface ◽  
Annealing Conditions ◽  
Coating Composition

Depth-sensing indentation (DSI) is used in this work to determine the change of local mechanical properties by annealing of hot-dip galvanized IF steel sheets. The influence of annealing conditions (temperature and time) on: (i) coating composition; (ii) local mechanical properties and (iii) roughness of the coating surface was quantified. Annealing of steel samples (Ti-IF steel and Ti-Nb-P-IF steel alloyed with phosphorus) was performed with different holding times (10, 60, and 300 s) by both temperatures 450 and 550 °C. The zinc in coating transformed during annealing to the intermetallic phases ZnxFey. Annealed Zn-Fe coatings, wherein the iron concentration falls towards the surface, consist of different intermetallic phases.

scholarly journals Application of the Non-Contact Video Gauge on the Mechanical Properties Test for Steel Cable at Elevated Temperature

2019 ◽  
Vol 9 (8) ◽  
pp. 1670 ◽  
Author(s):  
Yong Du ◽  
Zhang-ming Gou
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Ambient Temperature ◽  
Strain Gauge ◽  
Complex Shape ◽  
Full Range ◽  
Steel Cable ◽  
Stress Strain ◽  
Strain Stress ◽  
Steel Cables

As the limit of traditional contact measurement, it is difficult to precisely measure the steel cables twisted by a branch of wires especially at elevated temperature. In this paper the strain-stress relationships of S355 and S690 structural steel, 1860 MPa steel cable twisted by seven wires have been measured by the strain gauge, extensometer and non-contact video gauge at ambient temperature and elevated temperature, respectively. Comparison of the stress-strain curves gotten by different measuring technology, it indicates that the non-contact video gauge can provide a more efficient and reliable database than the strain gauge as well as extensometer, especially at an elevated temperature. It is worth noting that the non-contact video gauge can capture not only the full range of stress-strain curves of steel cables, but is also efficient for the specimens with a complex shape.

Study on bonding mechanism of hot-cast anchorage of Galfan-coated steel cables

2021 ◽  
Vol 246 ◽  
pp. 112980
Author(s):  
Hongbo Liu ◽  
Liulu Guo ◽  
Zhihua Chen ◽  
Yadan Meng ◽  
Yingjie Zhang
Keyword(s):  
Bonding Mechanism ◽  
Coated Steel ◽  
Steel Cables

Microstructure and Mechanical Properties of Aluminum/Stainless Steel Joints Welded by Different Weld Heat Input

2011 ◽  
Vol 189-193 ◽  
pp. 3253-3256
Author(s):  
Hong Tao Zhang ◽  
Jia Kun Liu ◽  
Hong Yun Zhao
Keyword(s):  
Mechanical Properties ◽  
Heat Input ◽  
Filler Metal ◽  
Dissimilar Metals ◽  
Coated Steel ◽  
Microstructure And Mechanical Properties ◽  
Zinc Coated Steel ◽  
Interfacial Intermetallic Compound ◽  
Steel Joints ◽  
Aluminum Base

Dissimilar metals joints between aluminum and zinc-coated steel were joined by CMT machine with ER4043 filler metal. The microstructure and mechanical properties of the joints obtained with different heat input were analyzed. The results showed that the thickness of interfacial intermetallic compound was determined by the welding heat input. Tensile specimens were broken in HAZ of aluminum base metal and the tensile strength of the joint can reach 122.3MPa.

Sign in / Sign up

Export Citation Format

Share Document