Absorption power cycles for low-temperature heat sources using aqueous salt solutions as working fluids

2016 ◽  
Vol 41 (7) ◽  
pp. 952-975 ◽  
Author(s):  
Vaclav Novotny ◽  
Michal Kolovratnik
Keyword(s):  
Low Temperature ◽  
Heat Sources ◽  
Salt Solutions ◽  
Working Fluids ◽  
Power Cycles ◽  
Aqueous Salt Solutions ◽  
Temperature Heat ◽  
Absorption Power

Optimization of Cycle and Expander Design of an Organic Rankine Cycle Unit Using Multi-Component Working Fluids

2016 ◽  
Author(s):  
Andrea Meroni ◽  
Jesper Graa Andreasen ◽  
Leonardo Pierobon ◽  
Fredrik Haglind
Keyword(s):  
Low Temperature ◽  
Power Systems ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Fluid Temperature ◽  
Heat Sources ◽  
Working Fluids ◽  
Turbine Performance ◽  
Temperature Heat

Organic Rankine cycle (ORC) power systems represent attractive solutions for power conversion from low temperature heat sources, and the use of these power systems is gaining increasing attention in the marine industry. This paper proposes the combined optimal design of cycle and expander for an organic Rankine cycle unit utilizing waste heat from low temperature heat sources. The study addresses a case where the minimum temperature of the heat source is constrained and a case where no constraint is imposed. The former case is the waste heat recovery from jacket cooling water of a marine diesel engine onboard a large ship, and the latter is representative of a low-temperature geothermal, solar or waste heat recovery application. Multi-component working fluids are investigated, as they allow improving the match between the temperature profiles in the heat exchangers and, consequently, reducing the irreversibility in the ORC system. This work considers mixtures of R245fa/pentane and propane/isobutane. The use of multi-component working fluids typically results in increased heat transfer areas and different expander designs compared to pure fluids. In order to properly account for turbine performance and design constraints in the cycle calculation, the thermodynamic cycle and the turbine are optimized simultaneously in the molar composition range of each mixture. Such novel optimization approach enables one to identify to which extent the cycle or the turbine behaviour influences the selection of the optimal solution. It also enables one to find the composition for which an optimal compromise between cycle and turbine performance is achieved. The optimal ORC unit employs pure R245fa and provides approximately 200 kW when the minimum hot fluid temperature is constrained. Conversely, the mixture R245fa/pentane (0.5/0.5) is selected and provides approximately 444 kW when the hot fluid temperature is not constrained to a lower value. In both cases, a compact and efficient turbine can be manufactured.

scholarly journals A Simple Method of Finding New Dry and Isentropic Working Fluids for Organic Rankine Cycle

Energies ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 480 ◽  
Author(s):  
Gábor Györke ◽  
Axel Groniewsky ◽  
Attila Imre
Keyword(s):  
Low Temperature ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Electricity Production ◽  
Working Fluid ◽  
Heat Sources ◽  
Simple Method ◽  
Working Fluids ◽  
Temperature Heat

One of the most crucial challenges of sustainable development is the use of low-temperature heat sources (60–200 °C), such as thermal solar, geothermal, biomass, or waste heat, for electricity production. Since conventional water-based thermodynamic cycles are not suitable in this temperature range or at least operate with very low efficiency, other working fluids need to be applied. Organic Rankine Cycle (ORC) uses organic working fluids, which results in higher thermal efficiency for low-temperature heat sources. Traditionally, new working fluids are found using a trial-and-error procedure through experience among chemically similar materials. This approach, however, carries a high risk of excluding the ideal working fluid. Therefore, a new method and a simple rule of thumb—based on a correlation related to molar isochoric specific heat capacity of saturated vapor states—were developed. With the application of this thumb rule, novel isentropic and dry working fluids can be found applicable for given low-temperature heat sources. Additionally, the importance of molar quantities—usually ignored by energy engineers—was demonstrated.

Analysis of a Combined Power and Ejector Refrigeration Cycle for Low Temperature Heat Sources

2009 ◽  
Author(s):  
Bin Zheng ◽  
Yiwu Weng
Keyword(s):  
Low Temperature ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Refrigeration Cycle ◽  
Heat Sources ◽  
Working Fluids ◽  
Temperature Heat ◽  
Cycle Efficiency

This paper presents a combined power and ejector refrigeration cycle for low temperature heat sources. The proposed cycle combines the organic Rankine cycle and the ejector refrigeration cycle. It can be used as an independent cycle powered by the low temperature sources, such as solar energy, geothermal energy, or as a bottom cycle of the conventional power plant for the recovery of low temperature waste heat. A program was developed to calculate the performance of the combined cycle. Several substances were selected as the working fluids including R113, R123, R245fa, R141b and R600. Simulation results show that R141b has the highest cycle efficiency, followed by R123, R113, R600 and then R245fa. While the working fluids are calculated by per unit, R600 can produce more power and refrigeration outputs due to the large latent heat. Simulations at different generating temperatures, evaporating temperatures and condensing temperatures were also discussed.

MODELING OF AN ORGANIC RANKINE CYCLE FOR LOW TEMPERATURE HEAT SOURCES

2018 ◽  
Author(s):  
Arthur Batista Martins Lott ◽  
Arthur Pacheco Luz ◽  
João Arthur Daconti Silva ◽  
Cristiana Maia ◽  
Sergio Hanriot
Keyword(s):  
Low Temperature ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Heat Sources ◽  
Temperature Heat

scholarly journals Analysis and Comparison of Some Low-Temperature Heat Sources for Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1853 ◽  
Author(s):  
Pavel Neuberger ◽  
Radomír Adamovský
Keyword(s):  
Heat Transfer ◽  
Low Temperature ◽  
Heat Source ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Ambient Air ◽  
Heat Transfer Fluid ◽  
Heat Sources ◽  
Ground Heat Exchangers ◽  
Temperature Heat

The efficiency of a heat pump energy system is significantly influenced by its low-temperature heat source. This paper presents the results of operational monitoring, analysis and comparison of heat transfer fluid temperatures, outputs and extracted energies at the most widely used low temperature heat sources within 218 days of a heating period. The monitoring involved horizontal ground heat exchangers (HGHEs) of linear and Slinky type, vertical ground heat exchangers (VGHEs) with single and double U-tube exchanger as well as the ambient air. The results of the verification indicated that it was not possible to specify clearly the most advantageous low-temperature heat source that meets the requirements of the efficiency of the heat pump operation. The highest average heat transfer fluid temperatures were achieved at linear HGHE (8.13 ± 4.50 °C) and double U-tube VGHE (8.13 ± 3.12 °C). The highest average specific heat output 59.97 ± 41.80 W/m2 and specific energy extracted from the ground mass 2723.40 ± 1785.58 kJ/m2·day were recorded at single U-tube VGHE. The lowest thermal resistance value of 0.07 K·m2/W, specifying the efficiency of the heat transfer process between the ground mass and the heat transfer fluid, was monitored at linear HGHE. The use of ambient air as a low-temperature heat pump source was considered to be the least advantageous in terms of its temperature parameters.

Sign in / Sign up

Export Citation Format

Share Document