Simulation of floor response spectra in shake table experiments

2010 ◽  
Vol 40 (6) ◽  
pp. 591-604 ◽  
Author(s):  
G. Maddaloni ◽  
K. P. Ryu ◽  
A. M. Reinhorn
Keyword(s):  
Response Spectra ◽  
Shake Table ◽  
Floor Response Spectra ◽  
Shake Table Experiments

Inclusion of Aircraft Crash into NPP Design Bases and Probabilistic Justification of Loads on Civil Structures and Equipment

2020 ◽  
pp. 35-47
Author(s):  
Nikita Chernukha
Keyword(s):  
Nuclear Power ◽  
Response Spectra ◽  
Mechanical Action ◽  
Exceedance Probability ◽  
Civil Structures ◽  
Method Of Calculation ◽  
Floor Response Spectra ◽  
Aircraft Trajectory ◽  
Probabilistic Justification ◽  
Aircraft Crash

The article is about nuclear power plant (NPP) safety analysis in case of aircraft crash. Specifically, the article considers the following problems: inclusion of aircraft crash into NPP design bases regarding calculation of frequency of an aircraft crash into NPP; aspects of justification of loads on NPP structures, systems and components (SSCs) caused by mechanical action of a primary missile – aircraft fuselage impact. Probabilistic characteristics of such random parameters as frequency of aircraft crash and direction of aircraft trajectory are determined by the results of analysis of world statistics of aviation accidents. Method of calculation of aircraft crash frequency on structures, buildings and NPP as a whole is presented. It takes into account options of accidental and intentional aircraft crashes and various aircraft approach scenarios. Procedure of probabilistic justification of loads on civil structures under aircraft impact is described. The loads are specified so as not to exceed allowable value of failure probability of NPP as a whole. Calculation of failure frequency of civil structures of existing NPP is given as an example to show analysis in case of a crash of an aircraft heavier than considered in NPP design. Procedure of probabilistic justification of dynamic loads on NPP equipment in case of aircraft impact is described. Method of floor response spectra (FRS) calculation with the required non-exceedance probability is given. Probabilistically justified loads in case of intentional aircraft impact (act of terrorism) are also considered. Additionally it is presented how internal forces calculated with the use of FRS with the required non-exceedance probability can be summed to provide analysis of subsystems.

Evaluation of floor acceleration demands from the 2017 Mexico City code seismic provisions using a continuous elastic model and records of instrumented buildings

2020 ◽  
Vol 36 (2_suppl) ◽  
pp. 213-237
Author(s):  
Miguel A Jaimes ◽  
Adrián D García-Soto
Keyword(s):  
Mexico City ◽  
Seismic Design ◽  
Soft Soil ◽  
Response Spectra ◽  
Elastic Model ◽  
Ground Acceleration ◽  
Nonstructural Components ◽  
Floor Response Spectra ◽  
Instrumented Buildings ◽  
Floor Acceleration

This study presents an evaluation of floor acceleration demands for the design of rigid and flexible acceleration-sensitive nonstructural components in buildings, calculated using the most recent Mexico City seismic design provisions, released in 2017. This evaluation includes two approaches: (1) a simplified continuous elastic model and (2) using recordings from 10 instrumented buildings located in Mexico City. The study found that peak floor elastic acceleration demands imposed on rigid nonstructural components into buildings situated in Mexico City might reach values of 4.8 and 6.4 times the peak ground acceleration at rock and soft sites, respectively. The peak elastic acceleration demands imposed on flexible nonstructural components in all floors, estimated using floor response spectra, might be four times larger than the maximum acceleration of the floor at the point of support of the component for buildings located in rock and soft soil. Comparison of results from the two approaches with the current seismic design provisions revealed that the peak acceleration demands and floor response spectra computed with the current 2017 Mexico City seismic design provisions are, in general, adequate.

Shake table experiments on masonry retaining wall reinforced with nails

2019 ◽  
pp. 538-543
Author(s):  
Tsuyoshi Takayanagi ◽  
Naoki Sawada ◽  
Osamu Nunokawa ◽  
Akihiro Takahashi
Keyword(s):  
Retaining Wall ◽  
Shake Table ◽  
Shake Table Experiments

Inelastic Analysis of Reinforced Concrete Shear Wall Structures Under Seismic Excitation

1993 ◽  
Author(s):  
Ming L. Wang
Keyword(s):  
Reinforced Concrete ◽  
Response Spectra ◽  
Shear Wall ◽  
Stiffness Degradation ◽  
Structural Stiffness ◽  
Hysteresis Model ◽  
Safety Equipment ◽  
Floor Response Spectra ◽  
Wall Structures ◽  
Degradation Models

Abstract During strong ground motions, members of reinforced concrete structures undergo cyclic deformations and experience permanent damage. Members may lose their initial stiffness as well as strength. Recently, Los Alamos National Laboratory has performed experiments on scale models of shear wall structures subjected to recorded earthquake signals. In general, the results indicated that the measured structural stiffness decreased with increased levels of excitation in the linear response region. Furthermore, a significant reduction in strength as well as in stiffness was also observed in the inelastic range. Since the in-structure floor response spectra, which are used to design and qualify safety equipment, have been based on calculated structural stiffness and frequencies, it is possible that certain safety equipment could experience greater seismic loads than specified for qualification due to stiffness reduction. In this research, a hysteresis model based on the concept of accumulated damage has been developed to account for this stiffness degradation both in the linear and inelastic ranges. Single and three degrees of freedom seismic Category I structures were analyzed and compared with equivalent linear stiffness degradation models in terms of maximum displacement responses, permanent displacement, and floor response spectra. The results indicate significant differences in responses between the hysteresis model and equivalent linear stiffness degradation models. The hysteresis model is recommended in the analysis of reinforced concrete shear-wall structures to obtain the in-structure floor response spectra for equipment qualification. Results of both cumulative and one shot tests are compared.

Sign in / Sign up

Export Citation Format

Share Document