Experimental study on the thermal performance and heat transfer characteristics of solar parabolic trough collector using Al2 O3 nanofluids

2017 ◽  
Vol 37 (3) ◽  
pp. 1149-1159 ◽  
Author(s):  
J. Subramani ◽  
P.K. Nagarajan ◽  
Somchai Wongwises ◽  
S.A. El-Agouz ◽  
Ravishankar Sathyamurthy
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Thermal Performance ◽  
Heat Transfer Characteristics ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Transfer Characteristics

Thermal performance of inserting hybrid nanofluid in parabolic trough collector

2021 ◽  
Author(s):  
Otabeh Al-Oran ◽  
Ferenc Lezsovits
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Thermal Performance ◽  
Hybrid Nanofluid ◽  
Heat Transfer Characteristics ◽  
Parabolic Trough ◽  
Transfer Coefficients ◽  
Parabolic Trough Collector ◽  
Heat Transfer Coefficients ◽  
Transfer Characteristics

AbstractIn this work, the thermal performance of using hybrid nanofluid of Ceria oxide and multi-walled carbon nanotube-based MOL 68 in the receiver tube of parabolic trough collector is simulated numerically. The influence of using this nanofluid under various volume concentrations and different Reynold numbers is solved numerically using computational fluid dynamics. The turbulent model's analysis is carried out based on k–ϵ re-normalization group and employed to find the Nusselt number and the heat transfer coefficients. The model results were validated with the previous correlation, which were used to evaluate the Nusselt number. The results showed that hybrid nanofluid enhances the heat transfer characteristics of the parabolic trough collector in comparison with the base fluid. Furthermore, even better heat transfer characteristics can be achieved with an increased volume concentration of the modified nanofluids.

scholarly journals Experimental study on heat transfer characteristics of a modified two-phase closed thermosyphon

2017 ◽  
Vol 21 (6 Part A) ◽  
pp. 2481-2489 ◽  
Author(s):  
Babak Aghel ◽  
Masoud Rahimi ◽  
Saeed Almasi
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Experimental Study ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Working Fluid ◽  
Heat Transfer Characteristics ◽  
Two Phase ◽  
Transfer Characteristics ◽  
Adiabatic Section

This study investigated the heat transfer characteristics of modified two-phase closed thermosyphon (TPCT) using water as the working fluid. In the modified TPCT, to reduce thermal resistance, a small TPCT was inserted inside the adiabatic section. For both the plain and modified thermosyphons the performances were determined at various heat inputs from 71-960 W. The results showed that the modified TPCT had less temperature difference between the evaporator and condenser sections than the plain one. According to the experimental data, in the modified TPCT, the thermal performance increased up to 20% over that of the unmodified one.

Maximizing Heat Transfer Through Joint Fin Systems

2005 ◽  
Vol 128 (2) ◽  
pp. 203-206 ◽  
Author(s):  
A.-R. A. Khaled
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Thermal Performance ◽  
Critical Length ◽  
The Other ◽  
Rigid Fixation ◽  
Convection Coefficient ◽  
Heat Transfer Characteristics ◽  
Cold Side ◽  
Transfer Characteristics

Heat transfer through joint fins is modeled and analyzed analytically in this work. The terminology “joint fin systems” is used to refer to extending surfaces that are exposed to two different convective media from its both ends. It is found that heat transfer through joint fins is maximized at certain critical lengths of each portion (the receiver fin portion which faces the hot side and the sender fin portion that faces the cold side of the convective media). The critical length of each portion of joint fins is increased as the convection coefficient of the other fin portion increases. At a certain value of the thermal conductivity of the sender fin portion, the critical length for the receiver fin portion may be reduced while heat transfer is maximized. This value depends on the convection coefficient for both fin portions. Thermal performance of joint fins is increased as both thermal conductivity of the sender fin portion or its convection coefficient increases. This work shows that the design of machine components such as bolts, screws, and others can be improved to achieve favorable heat transfer characteristics in addition to its main functions such as rigid fixation properties.

Sign in / Sign up

Export Citation Format

Share Document