scholarly journals Delay time in the transfer of modulation between microwave beams

2021 ◽  
Author(s):  
Ilaria Cacciari ◽  
Daniela Mugnai ◽  
Anedio Ranfagni
Keyword(s):  
Delay Time ◽  
Microwave Beams

Research on Prediction of High-Speed Rail Trains Delay Time

CICTP 2020 ◽  
2020 ◽  
Author(s):  
Jing Shi ◽  
Qiyuan Peng ◽  
Ling Liu
Keyword(s):  
Delay Time ◽  
High Speed ◽  
High Speed Rail

Synchronization of Chaotic Quantum Dot Light Emitting Diodes under Optical Feedback Effect

2020 ◽  
pp. 144-148
Keyword(s):  
Quantum Dot ◽  
Delay Time ◽  
Chaos Synchronization ◽  
Optical Feedback ◽  
Light Emitting Diode ◽  
Feedback Effect ◽  
Complete Synchronization ◽  
Light Emitting ◽  
Coupling Methods ◽  
Coupling Parameters

Chaos synchronization of delayed quantum dot light emitting diode has been studied theortetically which are coupled via the unidirectional and bidirectional. at synchronization of chaotic, The dynamics is identical with delayed optical feedback for those coupling methods. Depending on the coupling parameters and delay time the system exhibits complete synchronization, . Under proper conditions, the receiver quantum dot light emitting diode can be satisfactorily synchronized with the transmitter quantum dot light emitting diode due to the optical feedback effect.

Influence of the Laser Irradiation on the Delay Time of Start of Ar-Hg Discharge

2005 ◽  
Vol 125 (3) ◽  
pp. 235-240
Author(s):  
Terukazu Matsugi ◽  
Katsunori Arase ◽  
Hideki Motomura ◽  
Masafumi Jinno ◽  
Masaharu Aono
Keyword(s):  
Laser Irradiation ◽  
Delay Time

Delay Time Component of InGaAs MOSFET Caused by Dynamic Source Resistance

2014 ◽  
Vol E97.C (5) ◽  
pp. 419-422
Author(s):  
Masayuki YAMADA ◽  
Ken UCHIDA ◽  
Yasuyuki MIYAMOTO
Keyword(s):  
Delay Time ◽  
Time Component ◽  
Dynamic Source ◽  
Source Resistance ◽  
Ingaas Mosfet

Developing Wireless Energy Transfer Systems Using Microwave Beams: Applications and Prospects

2001 ◽  
Vol 55 (2) ◽  
pp. 10 ◽  
Author(s):  
A. A. Konovaltsev ◽  
Yu. A. Luchaninov ◽  
M. A. Omarov ◽  
Viktoriya M. Shokalo
Keyword(s):  
Energy Transfer ◽  
Wireless Energy Transfer ◽  
Microwave Beams

THERMAL BEHAVIOR AND IGNITION OF HIGH-ENERGY MATERIALS CONTAINING B, ALB2, AND TIB2

2020 ◽  
Author(s):  
A. G. Korotkikh ◽  
◽  
V. A. Arkhipov ◽  
I. V. Sorokin ◽  
E. A. Selikhova ◽  
...  
Keyword(s):  
Heat Flux ◽  
Thermal Behavior ◽  
Flux Density ◽  
Ignition Delay ◽  
Delay Time ◽  
Heat Flux Density ◽  
Ignition Delay Time ◽  
High Energy ◽  
Energy Materials ◽  
High Energy Materials

The paper presents the results of ignition and thermal behavior for samples of high-energy materials (HEM) based on ammonium perchlorate (AP) and ammonium nitrate (AN), active binder and powders of Al, B, AlB2, and TiB2. A CO2 laser with a heat flux density range of 90-200 W/cm2 was used for studies of ignition. The activation energy and characteristics of ignition for the HEM samples were determined. Also, the ignition delay time and the surface temperature of the reaction layer during the heating and ignition for the HEM samples were determined. It was found that the complete replacement of micron-sized aluminum powder by amorphous boron in a HEM sample leads to a considerable decrease in the ignition delay time by a factor of 2.2-2.8 at the same heat flux density due to high chemical activity and the difference in the oxidation mechanisms of boron particles. The use of aluminum diboride in a HEM sample allows one to reduce the ignition delay time of a HEM sample by a factor of 1.7-2.2. The quasi-stationary ignition temperature is the same for the AlB2-based and AlB12-based HEM samples.

Sign in / Sign up

Export Citation Format

Share Document