scholarly journals Teaching turbulent flow through pipe fittings using computational fluid dynamics approach

2020 ◽  
Vol 2 (1) ◽  
Author(s):  
Bhavesh D. Gajbhiye ◽  
Harshawardhan A. Kulkarni ◽  
Shashank S. Tiwari ◽  
Channamallikarjun S. Mathpati
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Turbulent Flow ◽  
Flow Through ◽  
Pipe Fittings

scholarly journals A Simple Transient Poiseuille-Based Approach to Mimic the Womersley Function and to Model Pulsatile Blood Flow

Dynamics ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 9-17
Author(s):  
Andrea Natale Impiombato ◽  
Giorgio La Civita ◽  
Francesco Orlandi ◽  
Flavia Schwarz Franceschini Zinani ◽  
Luiz Alberto Oliveira Rocha ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Blood Flow ◽  
Boundary Conditions ◽  
Quadratic Function ◽  
Pulsatile Blood Flow ◽  
Flow Through ◽  
Simplified Analysis ◽  
Function Models ◽  
Flow Reversals

As it is known, the Womersley function models velocity as a function of radius and time. It has been widely used to simulate the pulsatile blood flow through circular ducts. In this context, the present study is focused on the introduction of a simple function as an approximation of the Womersley function in order to evaluate its accuracy. This approximation consists of a simple quadratic function, suitable to be implemented in most commercial and non-commercial computational fluid dynamics codes, without the aid of external mathematical libraries. The Womersley function and the new function have been implemented here as boundary conditions in OpenFOAM ESI software (v.1906). The discrepancy between the obtained results proved to be within 0.7%, which fully validates the calculation approach implemented here. This approach is valid when a simplified analysis of the system is pointed out, in which flow reversals are not contemplated.

Computational Fluid Dynamics Techniques for Flows in Lapple Cyclone Separator

2005 ◽  
Vol 498-499 ◽  
pp. 179-185
Author(s):  
A.F. Lacerda ◽  
Luiz Gustavo Martins Vieira ◽  
A.M. Nascimento ◽  
S.D. Nascimento ◽  
João Jorge Ribeiro Damasceno ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Computational Fluid Dynamics ◽  
Turbulent Flow ◽  
Reynolds Stress ◽  
Cyclone Separator ◽  
Two Dimensional ◽  
Stress Components ◽  
Computational Fluid Dynamics Cfd

A two-dimensional fluidynamics model for turbulent flow of gas in cyclones is used to evaluate the importance of the anisotropic of the Reynolds stress components. This study presents consisted in to simulate through computational fluid dynamics (CFD) package the operation of the Lapple cyclone. Yields of velocity obtained starting from a model anisotropic of the Reynolds stress are compared with experimental data of the literature, as form of validating the results obtained through the use of the Computational fluid dynamics (Fluent). The experimental data of the axial and swirl velocities validate numeric results obtained by the model.

Computational Fluid Dynamics Analysis of Two Parallel Rectangular Jets Using OpenFOAM

2016 ◽  
Author(s):  
Han Li ◽  
Huhu Wang ◽  
Yassin A. Hassan ◽  
N. K. Anand
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Turbulent Flow ◽  
Stokes Equations ◽  
Laser Doppler Anemometry ◽  
Physical Models ◽  
Shear Stresses ◽  
Turbulence Characteristic ◽  
Computational Fluid Dynamics Analysis ◽  
Simulation Results

Two or multiple parallel jets are an important shear flow that widely existing in many industrial applications. The interaction between turbulence jets enables fast and thorough mixing of two fluids. The mixing feature of parallel jets has many engineering applications, such as, in Generation IV conceptual nuclear reactors, the coolants merge in upper or lower plenum after passing through the reactor core. While study of parallel jets mixing phenomenon, numerical experiments such as Computational Fluid Dynamics (CFD) simulations are extensively incorporated. Validation of varied turbulent models is of importance to make sure that the numerical results could be trusted and served as a guideline further design purpose. Many commercial CFD packages in the market such as FLUENT and Star CCM+ can provide the ability to simulate turbulent flow with predefined turbulence model, however, such commercial solvers may lack the flexibility that allow users build their own models for R&D purpose. The existing solvers in OpenFOAM are developed to fulfill both academic and industrial needs by achieving large-scale computational capability with a variety of physical models. Moreover, as an open source CFD toolbox, OpenFOAM grants users full control of the source code with complete freedom of customization. The purpose of this study is to perform CFD simulation using OpenFOAM for two submerged parallel jets issuing from two rectangular channels. Fully hexahedron multi-density mesh is generated using blockMesh utility to ensure velocity gradients are properly evaluated. A generalized-multi-grid solver is used to enhance convergence. Based on Reynolds-Averaged Navier-Stokes Equations (RANS), the realizable k-ε and k-ε shear stress transport (SST) are selected to model turbulent flow. Steady state Finite Volume solver simpleFoam is used to perform the simulation. In addition, data from experiments run in Thermal-Hydraulic Lab at Texas A&M University using particle image velocity (PIV) and Laser Doppler Anemometry (LDA) methods are considered in order to compare and validate simulation results. A number of turbulence characteristic such as mean velocities, turbulent intensities, z-component vorticity were compared with experiments. It was found that for stream-wise mean velocity profile as well as shear stresses, the realizable k-ε model exhibits a good agreement with experimental data. However, velocity fluctuation and turbulence intensities, simulation results showed a certain discrepancy.

scholarly journals The benefits of turbine endwall profiling in a cascade

2005 ◽  
Vol 219 (1) ◽  
pp. 49-59 ◽  
Author(s):  
G Ingram ◽  
D Gregory-Smith ◽  
N Harvey
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Turbulent Flow ◽  
Secondary Flow ◽  
Surface Flow ◽  
Transitional Flow ◽  
Loss Reduction ◽  
Small Reduction ◽  
Laminar And Turbulent Flow ◽  
Computational Fluid Dynamics Cfd

Non-axisymmetric profiled endwalls have been shown to reduce losses and secondary flow both in cascades and in rig tests. This paper presents experimental results which quantify the benefits of loss reduction in the cascade with particular attention to accuracy. The paper compares the benefits achieved in experiment to the results predicted by computational fluid dynamics (CFD). The results show that both the experiment and CFD give significant reductions in secondary flow. A reduction of 31 per cent in secondary loss has been measured for the best case, but the CFD gives only a small reduction in loss. Previous studies on the planar endwall have shown significant areas of transitional flow, so the surface flow has been studied with the aid of surface-mounted hot films. It was concluded that the loss reductions were not due to changes in regions of laminar and turbulent flow.

Multilaboratory Particle Image Velocimetry Analysis of the FDA Benchmark Nozzle Model to Support Validation of Computational Fluid Dynamics Simulations

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Prasanna Hariharan ◽  
Matthew Giarra ◽  
Varun Reddy ◽  
Steven W. Day ◽  
Keefe B. Manning ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Particle Image Velocimetry ◽  
Turbulent Flow ◽  
Medical Device ◽  
Particle Image ◽  
Transitional Flow ◽  
Flow Conditions ◽  
Image Velocimetry ◽  
Flow Case

This study is part of a FDA-sponsored project to evaluate the use and limitations of computational fluid dynamics (CFD) in assessing blood flow parameters related to medical device safety. In an interlaboratory study, fluid velocities and pressures were measured in a nozzle model to provide experimental validation for a companion round-robin CFD study. The simple benchmark nozzle model, which mimicked the flow fields in several medical devices, consisted of a gradual flow constriction, a narrow throat region, and a sudden expansion region where a fluid jet exited the center of the nozzle with recirculation zones near the model walls. Measurements of mean velocity and turbulent flow quantities were made in the benchmark device at three independent laboratories using particle image velocimetry (PIV). Flow measurements were performed over a range of nozzle throat Reynolds numbers (Rethroat) from 500 to 6500, covering the laminar, transitional, and turbulent flow regimes. A standard operating procedure was developed for performing experiments under controlled temperature and flow conditions and for minimizing systematic errors during PIV image acquisition and processing. For laminar (Rethroat=500) and turbulent flow conditions (Rethroat≥3500), the velocities measured by the three laboratories were similar with an interlaboratory uncertainty of ∼10% at most of the locations. However, for the transitional flow case (Rethroat=2000), the uncertainty in the size and the velocity of the jet at the nozzle exit increased to ∼60% and was very sensitive to the flow conditions. An error analysis showed that by minimizing the variability in the experimental parameters such as flow rate and fluid viscosity to less than 5% and by matching the inlet turbulence level between the laboratories, the uncertainties in the velocities of the transitional flow case could be reduced to ∼15%. The experimental procedure and flow results from this interlaboratory study (available at http://fdacfd.nci.nih.gov) will be useful in validating CFD simulations of the benchmark nozzle model and in performing PIV studies on other medical device models.

An Initial Parametric Study on Fluid Flow Through Bileaflet Mechanical Heart Valves Using Computational Fluid Dynamics

1994 ◽  
Vol 208 (2) ◽  
pp. 63-72 ◽  
Author(s):  
M J King ◽  
T David ◽  
J Fisher
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Heart Valve ◽  
Heart Valves ◽  
Mechanical Heart Valve ◽  
Volumetric Flow Rate ◽  
Flow Fields ◽  
Opening Angle ◽  
Bileaflet Mechanical Heart Valve ◽  
Flow Through

The effect of leaflet opening angle on flow through a bileaflet mechanical heart valve has been investigated using computational fluid dynamics (CFD). Steady state, laminar flow for a Newtonian fluid at a Reynolds number of 1500 was used in the two-dimensional model of the valve, ventricle, sinus and aorta. This computational model was verified using one-dimensional laser Doppler velocimetry (LDV). Although marked differences in the flow fields and energy dissipation of the jets downstream of the valve were found between the CFD predictions and the three-dimensional experimental model, both methods showed similar trends in the changes of the flow fields as the leaflet opening angle was altered. As the opening angle increased the area of recirculating fluid downstream of the leaflets, the pressure drop across the valve and the volumetric flow rate through the outer orifice decreased. For opening angles greater than 80° the jet through the outer orifice recombined with the central jet downstream of the leaflet; for an opening angle of 78° the jet through the outer orifice impinged on the aortic wall before recombining with the central jet. This study suggests that the opening angle has a marked effect on the flow downstream of the bileaflet mechanical heart valve and that valves with opening angles greater than 80° are preferable.

Sign in / Sign up

Export Citation Format

Share Document