Analysis of aerodynamic performance of high‐speed rotational components for MEMS based turbomachinery considering effects of tip clearance and diabatic heat transfer

2021 ◽  
Vol 104 (4) ◽  
Author(s):  
Shuusei Tanaka ◽  
Takaaki Nakai ◽  
Toshiyuki Toriyama
Keyword(s):  
Heat Transfer ◽  
High Speed ◽  
Aerodynamic Performance ◽  
Tip Clearance ◽  
Rotational Components

Multi-Objective Optimization of Turbine Blade Tip With Film Cooling Holes

2021 ◽  
Author(s):  
Shuai Yang ◽  
Min Zhang ◽  
Yan Liu ◽  
Jinguang Yang
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Aerodynamic Performance ◽  
Tip Clearance ◽  
Pareto Optimum ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Multi Objective ◽  
Film Cooling Holes

Abstract Tip leakage flow is inevitable due to the tip clearance over rotor blades in turbines. This phenomenondeteriorates blade aerodynamic performance and induces severe thermal damage to the tip surface.Introduction of cooling jets to the tip can effectively controls the tip leakage flow and improves the tip heat transfer. Therefore, this paper aims to optimize film cooling holes on a flat tip of a subsonic cascade and an topology-optimized tip of a transonic cascade. A design variable is a material parameter defined at each grid node along the blade camber line. This idea is based on the topology optimization method. The objective is to minimize blade energy loss and maximize tip heat transfer intensity. A response surface optimization based on the design of experiment (DOE) analysis is employed, and a multi-objective Genetic Algorithm is used to get Pareto optimum solutions. During the DOE process, a CFD method using injection source terms is integrated for numerical simulations to reduce computational costs. Optimized tip film cooling holes are finally re-constructed. The influence of the newly designed tip cooling holes configuration on blade aero-thermal performance is evaluated via CFD simulations using body-fitted mesh. Results show that compared with the uniform arrangement of cooling film holes along the axial direction, all the optimized film cooling holes can improve both blade aerodynamic performance and tip heat transfer performance.

Effect of the strip spacing on the aerodynamic performance of a high-speed double-strip pantograph

2021 ◽  
pp. 1-17
Author(s):  
Zhiyuan Dai ◽  
Tian Li ◽  
Jian Deng ◽  
Ning Zhou ◽  
Weihua Zhang
Keyword(s):  
High Speed ◽  
Aerodynamic Performance

Experimental investigation of wall heat transfer due to spray combustion in a high-pressure/high-temperature vessel

2021 ◽  
pp. 146808742110072
Author(s):  
Karri Keskinen ◽  
Walter Vera-Tudela ◽  
Yuri M Wright ◽  
Konstantinos Boulouchos
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
High Pressure ◽  
High Temperature ◽  
High Speed ◽  
Transfer Problem ◽  
Wall Heat Transfer ◽  
Gas Temperature ◽  
Reference Case ◽  
High Pressure High Temperature

Combustion chamber wall heat transfer is a major contributor to efficiency losses in diesel engines. In this context, thermal swing materials (adapting to the surrounding gas temperature) have been pinpointed as a promising mitigative solution. In this study, experiments are carried out in a high-pressure/high-temperature vessel to (a) characterise the wall heat transfer process ensuing from wall impingement of a combusting fuel spray, and (b) evaluate insulative improvements provided by a coating that promotes thermal swing. The baseline experimental condition resembles that of Spray A from the Engine Combustion Network, while additional variations are generated by modifying the ambient temperature as well as the injection pressure and duration. Wall heat transfer and wall temperature measurements are time-resolved and accompanied by concurrent high-speed imaging of natural luminosity. An investigation with an uncoated wall is carried out with several sensor locations around the stagnation point, elucidating sensor-to-sensor variability and setup symmetry. Surface heat flux follows three phases: (i) an initial peak, (ii) a slightly lower plateau dependent on the injection duration, and (iii) a slow decline. In addition to the uncoated reference case, the investigation involves a coating made of porous zirconia, an established thermal swing material. With a coated setup, the projection of surface quantities (heat flux and temperature) from the immersed measurement location requires additional numerical analysis of conjugate heat transfer. Starting from the traces measured beneath the coating, the surface quantities are obtained by solving a one-dimensional inverse heat transfer problem. The present measurements are complemented by CFD simulations supplemented with recent rough-wall models. The surface roughness of the coated specimen is indicated to have a significant impact on the wall heat flux, offsetting the expected benefit from the thermal swing material.

Influence of tip clearance and cavity depth on heat transfer in a cutback squealer tip

2020 ◽  
pp. 095441002096469
Author(s):  
Weijie Wang ◽  
Shaopeng Lu ◽  
Hongmei Jiang ◽  
Qiusheng Deng ◽  
Jinfang Teng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Suction Side ◽  
High Heat ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Cavity Depth ◽  
High Heat Transfer ◽  
Blade Tip ◽  
High Heat Transfer Coefficient

Numerical simulations are conducted to present the aerothermal performance of a turbine blade tip with cutback squealer rim. Two different tip clearance heights (0.5%, 1.0% of the blade span) and three different cavity depths (2.0%, 3.0%, and 6.0% of the blade span) are investigated. The results show that a high heat transfer coefficient (HTC) strip on the cavity floor appears near the suction side. It extends with the increase of tip clearance height and moves towards the suction side with the increase of cavity depth. The cutback region near the trailing edge has a high HTC value due to the flush of over-tip leakage flow. High HTC region shrinks to the trailing edge with the increase of cavity depth since there is more accumulated flow in the cavity for larger cavity depth. For small tip clearance cases, high HTC distribution appears on the pressure side rim. However, high HTC distribution is observed on suction side rim for large tip clearance height. This is mainly caused by the flow separation and reattachment on the squealer rims.

Sign in / Sign up

Export Citation Format

Share Document