Investigation of the distortion factor for Bussgang noise cancellation iterative receivers

2019 ◽  
Vol 32 (9) ◽  
pp. e3960
Author(s):  
Nargis Bibi ◽  
Nazeer Muhammad ◽  
Barry Cheetham
Keyword(s):  
Noise Cancellation ◽  
Distortion Factor ◽  
Iterative Receivers

THE GENERALIZED PREDICTIV COMMAND APPLIED TO THE NOISE CANCELLATION

1990 ◽  
Vol 51 (C2) ◽  
pp. C2-765-C2-768
Author(s):  
C. DUVERMY ◽  
E. ORTOLA
Keyword(s):  
Noise Cancellation

scholarly journals Using Benford’s law to assess the quality of COVID-19 register data in Brazil

2020 ◽  
Author(s):  
Lucas Silva ◽  
Dalson Figueiredo Filho
Keyword(s):  
Goodness Of Fit ◽  
Epidemiological Surveillance ◽  
Evidence Based ◽  
Mean Absolute Deviation ◽  
Chi Square ◽  
Absolute Deviation ◽  
Distortion Factor ◽  
Benford Law ◽  
Official Data

Abstract We employ Newcomb–Benford law (NBL) to evaluate the reliability of COVID-19 figures in Brazil. Using official data from February 25 to September 15, we apply a first digit test for a national aggregate dataset of total cases and cumulative deaths. We find strong evidence that Brazilian reports do not conform to the NBL theoretical expectations. These results are robust to different goodness of fit (chi-square, mean absolute deviation and distortion factor) and data sources (John Hopkins University and Our World in Data). Despite the growing appreciation for evidence-based-policymaking, which requires valid and reliable data, we show that the Brazilian epidemiological surveillance system fails to provide trustful data under the NBL assumption on the COVID-19 epidemic.

scholarly journals Low-Frequency Signal Sampling Method Implemented in a PLC Controller Dedicated to Applications in the Monitoring of Selected Electrical Devices

Electronics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 442
Author(s):  
Marcin Jaraczewski ◽  
Ryszard Mielnik ◽  
Tomasz Gębarowski ◽  
Maciej Sułowicz
Keyword(s):  
Power System ◽  
Reactive Power ◽  
Low Frequency ◽  
Sampling Frequency ◽  
Electrical Signal ◽  
Distortion Factor ◽  
Electrical Devices ◽  
Frequency Sampling ◽  
Sampled Signal ◽  
Band Limited

High requirements for power systems, and hence for electrical devices used in industrial processes, make it necessary to ensure adequate power quality. The main parameters of the power system include the rms-values of the current, voltage, and active and reactive power consumed by the loads. In previous articles, the authors investigated the use of low-frequency sampling to measure these parameters of the power system, showing that the method can be easily implemented in simple microcontrollers and PLCs. This article discusses the methods of measuring electrical quantities by devices with low computational efficiency and low sampling frequency up to 1 kHz. It is not obvious that the signal of 50–500 Hz can be processed using the sampling frequency of fs = 47.619 Hz because it defies the Nyquist–Shannon sampling theorem. This theorem states that a reconstruction of a sampled signal is only guaranteed possible for a bandlimit fmax < fs, where fmax is the maximum frequency of a sampled signal. Therefore, theoretically, neither 50 nor 500 Hz can be identified by such a low-frequency sampling. Although, it turns out that if we have a longer period of a stable multi-harmonic signal, which is band-limited (from the bottom and top), it allows us to map this band to the lower frequencies, thus it is possible to use the lower sampling ratio and still get enough precise information of its harmonics and rms value. The use of aliasing for measurement purposes is not often used because it is considered a harmful phenomenon. In our work, it has been used for measurement purposes with good results. The main advantage of this new method is that it achieves a balance between PLC processing power (which is moderate or low) and accuracy in calculating the most important electrical signal indicators such as power, RMS value and sinusoidal-signal distortion factor (e.g., THD). It can be achieved despite an aliasing effect that causes different frequencies to become indistinguishable. The result of the research is a proposal of error reduction in the low-frequency measurement method implemented on compact PLCs. Laboratory tests carried out on a Mitsubishi FX5 compact PLC controller confirmed the correctness of the proposed method of reducing the measurement error.

Sign in / Sign up

Export Citation Format

Share Document