ChemInform Abstract: Electrochromic Display Devices of Tungstic Oxide Containing Vanadium Oxide or Cadmium Sulfide as a Light-Sensitive Layer.

ChemInform ◽  
2010 ◽  
Vol 25 (10) ◽  
pp. no-no
Author(s):  
P. M. S. MONK ◽  
J. A. DUFFY ◽  
M. D. INGRAM
Keyword(s):  
Vanadium Oxide ◽  
Cadmium Sulfide ◽  
Sensitive Layer ◽  
Display Devices ◽  
Tungstic Oxide

Liquid crystals in display devices

1972 ◽  
Vol 107 (7) ◽  
pp. 503 ◽  
Author(s):  
A.A. Groshev ◽  
V.B. Sergeev
Keyword(s):  
Liquid Crystals ◽  
Display Devices

Enhanced Electroluminescence of Urethane Containing Processable Polythiophene Derivative by Addition of Dye Molecules

2000 ◽  
Vol 660 ◽  
Author(s):  
Amarjeet Kaur ◽  
Mario J. Cazeca ◽  
Kethinni G. Chittibabu ◽  
Jayant Kumar ◽  
Sukant K. Tripathy
Keyword(s):  
Fluorescent Dyes ◽  
Visible Region ◽  
Dye Molecules ◽  
Flat Panel Display ◽  
Large Area ◽  
Good Efficiency ◽  
Display Devices ◽  
Yellow Color ◽  
Organic Electroluminescent ◽  
Important Approach

ABSTRACTOrganic electroluminescent (EL) diodes based on fluorescent dyes and conducting polymers have attracted the interest of researchers, mainly because of their emission in the visible region and for application to large area portable flat panel display devices, driven at low voltages. Therefore, for the development of higher efficiency polymer EL diodes, the optimal combination of the merits of organic fluorescent dye molecules with that of conjugated polymer is an important approach. We report electroluminescence studies of polymer light emitting diodes (p-LEDs) fabricated with poly[2-(3-thienyl)ethanol n-butoxy carbonylmethyl urethane] (PURET) and its composite with 4-dicyanomethylene-2-methyl-6-(p-dimethylaminostyryl)-4H pyran (DCM) dye. These materials have been chosen in view of the fact that PURET exhibits a small overlap between emission and absorption spectra whereas DCM has a good efficiency of trapping both electrons as well as holes. Polyaniline has been utilized as hole injecting layer whereas tris-8-hydroxyquinoline-aluminum as electron injecting layer. Enhanced electroluminescence with bright yellow color has been observed in p-LEDs by the addition of dye.

Study of the microstructure and particles of vanadium (III) oxide, vanadium (V) oxide and lithium aluminate powders

2020 ◽  
Vol 86 (1) ◽  
pp. 32-37
Author(s):  
Valeria A. Brodskaya ◽  
Oksana A. Molkova ◽  
Kira B. Zhogova ◽  
Inga V. Astakhova
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Vanadium Oxide ◽  
Size Distribution ◽  
Microstructural Analysis ◽  
Coherent Scattering ◽  
Powder Materials ◽  
Lithium Aluminate ◽  
Range Limit ◽  
Oxide Particles

Powder materials are widely used in the manufacture of electrochemical elements of thermal chemical sources of current. Electrochemical behavior of the powders depends on the shape and size of their particles. The results of the study of the microstructure and particles of the powders of vanadium (III), (V) oxides and lithium aluminate obtained by transmission electron and atomic force microscopy, X-ray diffraction and gas adsorption analyses are presented. It is found that the sizes of vanadium (III) and vanadium (V) oxide particles range within 70 – 600 and 40 – 350 nm, respectively. The size of the coherent-scattering regions of the vanadium oxide particles lies in the lower range limit which can be attributed to small size of the structural elements (crystallites). An average volumetric-surface diameter calculated on the basis of the surface specific area is close to the upper range limit which can be explained by the partial agglomeration of the powder particles. Unlike the vanadium oxide particles, the range of the particle size distribution of the lithium aluminate powder is narrower — 50 – 110 nm. The values of crystallite sizes are close to the maximum of the particle size distribution. Microstructural analysis showed that the particles in the samples of vanadium oxides have a rounded (V2O3) or elongated (V2O5) shape; whereas the particles of lithium aluminate powder exhibit lamellar structure. At the same time, for different batches of the same material, the particle size distribution is similar, which indicates the reproducibility of the technologies for their manufacture. The data obtained can be used to control the constancy of the particle size distribution of powder materials.

Sign in / Sign up

Export Citation Format

Share Document