ChemInform Abstract: Synthesis of Superconducting Thick Films of Bi-Ca-Sr-Cu-O Systems by the Screen Printing Method.

ChemInform ◽  
2010 ◽  
Vol 24 (48) ◽  
pp. no-no
Author(s):  
M. YA. KHODOS ◽  
M. K. BOEVA ◽  
A. A. FOTIEV
Keyword(s):  
Screen Printing ◽  
Thick Films ◽  
Screen Printing Method ◽  
Superconducting Thick Films ◽  
Printing Method

Structural and Dielectric Properties of Screen Printed PZT(70/30) Multilayered Thick Films

2007 ◽  
Vol 124-126 ◽  
pp. 663-666 ◽  
Author(s):  
Sung Gap Lee ◽  
Sang Man Park ◽  
Young Jae Shim ◽  
Young Chul Rhee
Keyword(s):  
Screen Printing ◽  
Remanent Polarization ◽  
Thick Films ◽  
Sol Gel ◽  
Relative Dielectric Constant ◽  
Polycrystalline Structure ◽  
Coating Solution ◽  
Screen Printing Method ◽  
Xrd Patterns ◽  
Printing Method

PZT(70/30) powder was prepared by a sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The coating and drying procedure was repeated 4 times. And then the PZT(30/70) precusor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5 mol/L and the number of coating was varied from 0 to 6. The porosity decreased and the grain size increased with increasing the number of coatings. The thickness of the PZT-6(6: number of coatings) films was about 60~65μm. All PZT thick films showed the typical XRD patterns of a typical perovskite polycrystalline structure. The relative dielectric constant of the PZT-6 thick film was 540. The remanent polarization and coercive field of the PZT-6 film were 23.6 μC /cm2, 12.0 kV/cm, respectively.

SYNTHESIS OF CoFe2O4/Pb(Zr0.53Ti0.47)O3 MULTIFERROIC COMPOSITE THICK FILMS BY LOW-SINTERING-TEMPERATURE SCREEN PRINTING METHOD

2011 ◽  
Vol 01 (01) ◽  
pp. 119-125 ◽  
Author(s):  
W. CHEN ◽  
C. X. HUANG ◽  
T. S. YAN ◽  
W. ZHU ◽  
Z. P. LI ◽  
...  
Keyword(s):  
Screen Printing ◽  
Sintering Temperature ◽  
Ferroelectric Properties ◽  
Thick Films ◽  
Electron Microscopic ◽  
Screen Printing Method ◽  
Pzt Films ◽  
Multiferroic Composite ◽  
Low Sintering Temperature ◽  
Printing Method

CoFe 2 O 4/ Pb ( Zr 0.53 Ti 0.47) O 3 (abbreviated as CFO/PZT) multiferroic composite thick films were successfully fabricated on alumina substrate with gold bottom electrode by screen printing method at a low-sintering temperature. The processing included the modification and dispersion of ferromagnetic CFO powder and ferroelectric PZT powder, the preparation of uniform pastes, and the selection of proper annealing temperature for composite thick films. Transmission electron microscopic pictures (TEM) indicated the submicron meter of particles size for both CFO and PZT particles. After annealing at 900°C for 1 h in air, tape test confirmed the quality of multiferroic thick films as well as pure CFO and PZT films. X-ray diffraction (XRD) showed a coexistence of CFO and PZT phases; furthermore, a smooth surface was observed through scanning electron microscopic (SEM) pictures along with the sharp cross-sectional picture, indicative of 100 μm of film thickness. Ferromagnetic and ferroelectric properties were observed in CFO/PZT films simultaneously at room temperature. Compared with the reported CFO/PZT multiferrroic thin films, the present ferromagnetic property was closing to that of the chemical sol-gel synthesized film and even that from the physical pulsed laser deposition technique. However, the ferroelectric property showed a degenerated behavior, possible reasons for this was discussed and further optimization was also proposed for the potential multifunctional application.

Electrical Properties BaTiO3 Thick Films with an Interlayer SrTiO3 Thin Films

2007 ◽  
Vol 124-126 ◽  
pp. 659-662
Author(s):  
Sung Pill Nam ◽  
Sung Gap Lee ◽  
Seong Gi Bae ◽  
Young Hie Lee
Keyword(s):  
Thin Films ◽  
Leakage Current ◽  
Spin Coating ◽  
Screen Printing ◽  
Thick Films ◽  
Sol Gel ◽  
Grain Structure ◽  
Screen Printing Method ◽  
Coating Method ◽  
Printing Method

The BaTiO3/SrTiO3 heterolayered thick films were fabricated by two different methods – thick films of BaTiO3 by screen printing method on alumina substrates electrodes with Pt, thin films of SrTiO3 by the spin-coating method on BaTiO3 thick films and once more thick films of BaTiO3 by the screen printing method on SrTiO3 layer. The leakage current and the dielectric properties were investigated for effect of various stacking sequence of sol-gel-prepared SrTiO3 layer at interface of BaTiO3 thick films. The insertion of SrTiO3 interlayer yielded BaTiO3 thick films with homogeneous and dense grain structure with the number of SrTiO3 layers. The leakage current density of the BaTiO3/SrTiO3-7 film is less that 1.5 10-9 A/cm2 at 5 V.

Sign in / Sign up

Export Citation Format

Share Document