05.12: Effect of initial imperfection on elasto-plastic behavior of SHS columns under axial force with bending moment

ce/papers ◽  
2017 ◽  
Vol 1 (2-3) ◽  
pp. 1123-1132
Author(s):  
Kazuya Mitsui ◽  
Atsushi Sato ◽  
Masahiro Aoyama
Keyword(s):  
Axial Force ◽  
Initial Imperfection ◽  
Bending Moment ◽  
Plastic Behavior

Load Regime Diagram of a Pipe With Cyclically Plastic Bending

2002 ◽  
Author(s):  
Yanping Yao ◽  
Ming-Wan Lu
Keyword(s):  
Axial Force ◽  
Bending Moment ◽  
Boundary Curve ◽  
Plastic Behavior ◽  
Cyclic Bending ◽  
Elastic Plastic ◽  
Linear Elastic ◽  
Load Regime ◽  
Reversed Cyclic ◽  
Cyclic Bending Moment

The criteria of piping seismic design based on linear elastic analysis has been proved to be conservative, which is mainly because the influence of plastic deformation on piping dynamic response is neglected. In the present paper, a pipe under seismic excitation is simplified as an beam with tubular cross section subjected to steady axial force and fully reversed cyclic bending moment, and the elastic-plastic behavior of the pipe is studied. Various behavior of the pipe under different combinations of axial force and cyclic bending moment is discussed and the boundary curve equations between them are obtained. Also the load regime diagram for a pipe which is formed by the boundary curve equations in the loading plane is given, from which the elastic-plastic behavior of the pipe can be determined directly.

Closed-form moment-curvature relations for reinforced concrete cross sections under bending moment and axial force

2016 ◽  
Vol 129 ◽  
pp. 67-80 ◽  
Author(s):  
Pedro Dias Simão ◽  
Helena Barros ◽  
Carla Costa Ferreira ◽  
Tatiana Marques
Keyword(s):  
Reinforced Concrete ◽  
Closed Form ◽  
Axial Force ◽  
Cross Sections ◽  
Bending Moment

Preliminary Parametric Assessment of a Bolted Endplate Joint under Combined Axial Force and Cyclic Bending Moment

2011 ◽  
Vol 255-260 ◽  
pp. 718-721
Author(s):  
Z.Y. Wang ◽  
Q.Y. Wang
Keyword(s):  
Finite Element Analysis ◽  
Axial Force ◽  
Seismic Design ◽  
Axial Load ◽  
Failure Modes ◽  
Bending Moment ◽  
Element Analysis ◽  
Cyclic Behaviour ◽  
Joint Behaviour ◽  
Steel Joints

Problems regarding the combined axial force and bending moment for the behaviour of semi-rigid steel joints under service loading have been recognized in recent studies. As an extended research on the cyclic behaviour of a bolted endplate joint, this study is performed relating to the contribution of column axial force on the cyclic behaviour of the joint. Using finite element analysis, the deteriorations of the joint performance have been evaluated. The preliminary parametric study of the joint is conducted with the consideration of flexibility of the column flange. The column axial force was observed to significantly influence the joint behaviour when the bending of the column flange dominates the failure modes. The reductions of moment resistance predicted by numerical analysis have been compared with codified suggestions. Comments have been made for further consideration of the influence of column axial load in seismic design of bolted endplate joints.

A Simple Approach for Including Weld Residual Stresses in the Calculation of Pipe Circumferential Through-Wall Crack Opening Displacements

2016 ◽  
Author(s):  
Richard Olson
Keyword(s):  
Residual Stresses ◽  
Axial Force ◽  
Analytic Solution ◽  
Crack Opening ◽  
Bending Moment ◽  
Generalized Solution ◽  
Finite Element Analyses ◽  
Opening Displacement ◽  
Crack Face ◽  
Basic Equations

Current methodologies for predicting the crack opening displacement (COD) of circumferentially through-wall cracked pipe do not include the effect of weld residual stresses (WRS). Even the most advanced COD prediction methodology only includes the effect of applied axial force, bending moment, and crack face pressure. For some years, it has been known that weld residual stresses do alter the COD, but there has been no convenient way to include them in a COD prediction without doing case-specific finite element analyses. This paper documents a generalized solution for including WRS effects on COD. The model uses a closed-form analytic solution to approximate the crack face rotations that the WRS would induce which, subsequently, can be added to the typical axial force-bending-crack face pressure COD solution. The methodology is described and the basic equations for the solution are presented. Following this, application to cases to evaluate the efficacy of the approach are presented which show a mixture of results ranging from amazingly good to “of questionable value” with respect to the FEA results.

The Influence of Rotatory Inertia and Transverse Shear on the Dynamic Plastic Behavior of Beams

1979 ◽  
Vol 46 (2) ◽  
pp. 303-310 ◽  
Author(s):  
Norman Jones ◽  
J. Gomes de Oliveira
Keyword(s):  
Transverse Shear ◽  
Shear Force ◽  
Yield Criterion ◽  
Yield Condition ◽  
Bending Moment ◽  
Plastic Behavior ◽  
Plastic Response ◽  
Rotatory Inertia ◽  
Perfectly Plastic ◽  
Theoretical Procedure

The theoretical procedure presented herein examines the influence of retaining the transverse shear force in the yield criterion and rotatory inertia on the dynamic plastic response of beams. Exact theoretical rigid perfectly plastic solutions are presented for a long beam impacted by a mass and a simply supported beam loaded impulsively. It transpires that rotatory inertia might play a small, but not negligible, role on the response of these beams. The results in the various figures indicate that the greatest departure from an analysis which neglects rotatory inertia but retains the influence of the bending moment and transverse shear force in the yield condition is approximately 11 percent for the particular range of parameters considered.

Sign in / Sign up

Export Citation Format

Share Document