Validation of Simulation and Mass Transfer Coefficient Prediction with Interfacial Convection

2017 ◽  
Vol 40 (6) ◽  
pp. 1059-1068 ◽  
Author(s):  
Botong Liu ◽  
Botan Liu ◽  
Xiaolong Ge ◽  
Xigang Yuan
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Interfacial Convection

Absorption of oxygen into solutions of polymers

1986 ◽  
Vol 51 (10) ◽  
pp. 2127-2134 ◽  
Author(s):  
František Potůček ◽  
Jiří Stejskal
Keyword(s):  
Mass Transfer ◽  
Aqueous Solutions ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Liquid Flow ◽  
Flow Curve ◽  
Liquid Flow Rate ◽  
Polymer Concentration ◽  
Newtonian Liquids

Absorption of oxygen into water and aqueous solutions of poly(acrylamides) was studied in an absorber with a wetted sphere. The effects of changes in the liquid flow rate and the polymer concentration on the liquid side mass transfer coefficient were examined. The results are expressed by correlations between dimensionless criteria modified for non-Newtonian liquids whose flow curve can be described by the Ostwald-de Waele model.

scholarly journals Development of mass and heat transfer coupled model of hollow fiber membrane for salt recovery from brine via osmotic membrane distillation

2021 ◽  
Vol 33 (1) ◽  
Author(s):  
Sher Ahmad ◽  
Gabriela Vollet Marson ◽  
Waheed Ur Rehman ◽  
Mohammad Younas ◽  
Sarah Farrukh ◽  
...  
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Heat And Mass Transfer ◽  
Hollow Fiber ◽  
Hollow Fiber Membrane ◽  
Membrane Distillation ◽  
Fiber Membrane ◽  
Salt Recovery ◽  
Osmotic Solution

Abstract Background In this research work, a coupled heat and mass transfer model was developed for salt recovery from concentrated brine water through an osmotic membrane distillation (OMD) process in a hollow fiber membrane contactor (HFMC).The model was built based on the resistance-in-series concept for water transport across the hydrophobic membrane. The model was adopted to incorporate the effects of polarization layers such as temperature and concentration polarization, as well as viscosity changes during concentration. Results The modeling equations were numerically simulated in MATLAB® and were successfully validated with experimental data from literature with a deviation within the range of 1–5%. The model was then applied to study the effects of key process parameters like feed concentrations, osmotic solution concentration, feed, and osmotic solution flow rates and feed temperature on the overall heat and mass transfer coefficient as well as on water transport flux to improve the process efficiency. The mass balance modeling was applied to calculate the membrane area based on the simulated mass transfer coefficient. Finally, a scale-up for the MD process for salt recovery on an industrial scale was proposed. Conclusions This study highlights the effect of key parameters for salt recovery from wastewater using the membrane distillation process. Further, the applicability of the OMD process for salt recovery on large scale was investigated. Sensitivity analysis was performed to identify the key parameters. From the results of this study, it is concluded that the OMD process can be promising in salt recovery from wastewater.

scholarly journals Hydrodynamics and Mass Transfer in a Concentric Internal Jet-Loop Airlift Bioreactor Equipped with a Deflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4329
Author(s):  
Radek Šulc ◽  
Jan Dymák
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Liquid System ◽  
Gas Holdup ◽  
Gas Velocity ◽  
Liquid Phase Mass Transfer ◽  
Homogenization Time ◽  
Standard Design ◽  
Superficial Gas Velocity

The gas–liquid hydrodynamics and mass transfer were studied in a concentric tube internal jet-loop airlift reactor with a conical bottom. Comparing with a standard design, the gas separator was equipped with an adjustable deflector placed above the riser. The effect of riser superficial gas velocity uSGR on the total gas holdup εGT, homogenization time tH, and overall volumetric liquid-phase mass transfer coefficient kLa was investigated in a laboratory bioreactor, of 300 mm in inner diameter, in a two-phase air–water system and three-phase air–water–PVC–particle system with the volumetric solid fraction of 1% for various deflector clearances. The airlift was operated in the range of riser superficial gas velocity from 0.011 to 0.045 m/s. For the gas–liquid system, when reducing the deflector clearance, the total gas holdup decreased, the homogenization time increased twice compared to the highest deflector clearance tested, and the overall volumetric mass transfer coefficient slightly increased by 10–17%. The presence of a solid phase shortened the homogenization time, especially for lower uSGR and deflector clearance, and reduced the mass transfer coefficient by 15–35%. Compared to the gas–liquid system, the noticeable effect of deflector clearance was found for the kLa coefficient, which was found approx. 20–29% higher for the lowest tested deflector clearance.

scholarly journals Gas–liquid mass transfer characteristics of aviation fuel scrubbing in an aircraft fuel tank

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Li Chaoyue ◽  
Feng Shiyu ◽  
Xu Lei ◽  
Peng Xiaotian ◽  
Yan Yan
Keyword(s):  
Mass Transfer ◽  
Dissolved Oxygen ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Oxygen Concentration ◽  
Gas Holdup ◽  
Aviation Fuel ◽  
Volumetric Mass Transfer Coefficient ◽  
Dissolved Oxygen Concentration ◽  
Liquid Mass Transfer

AbstractDissolved oxygen evolving from aviation fuel leads to an increase in the oxygen concentration in an inert aircraft fuel tank ullage that may increase the flammability of the tank. Aviation fuel scrubbing with nitrogen-enriched air (NEA) can largely reduce the amount of dissolved oxygen and counteract the adverse effect of oxygen evolution. The gas–liquid mass transfer characteristics of aviation fuel scrubbing are investigated using the computational fluid dynamics method, which is verified experimentally. The effects of the NEA bubble diameter, NEA superficial velocity and fuel load on oxygen transfer between NEA and aviation fuel are discussed. Findings from this work indicate that the descent rate of the average dissolved oxygen concentration, gas holdup distribution and volumetric mass transfer coefficient increase with increasing NEA superficial velocity but decrease with increasing bubble diameter and fuel load. When the bubble diameter varies from 1 to 4 mm, the maximum change of descent rate of dissolved oxygen concentration is 18.46%, the gas holdup is 8.73%, the oxygen volumetric mass transfer coefficient is 81.45%. When the NEA superficial velocities varies from 0.04 to 0.10 m/s, the maximum change of descent rate of dissolved oxygen concentration is 146.77%, the gas holdup is 77.14%, the oxygen volumetric mass transfer coefficient is 175.38%. When the fuel load varies from 35 to 80%, the maximum change of descent rate of dissolved oxygen concentration is 21.15%, the gas holdup is 49.54%, the oxygen volumetric mass transfer coefficient is 44.57%. These results provide a better understanding of the gas and liquid mass transfer characteristics of aviation fuel scrubbing in aircraft fuel tanks and can promote the optimal design of fuel scrubbing inerting systems.

Mass Transfer Coefficients during Steel Decarburization in a RH Degasser

2008 ◽  
Vol 273-276 ◽  
pp. 679-684
Author(s):  
Roberto Parreiras Tavares ◽  
André Afonso Nascimento ◽  
Henrique Loures Vale Pujatti
Keyword(s):  
Mass Transfer ◽  
Reynolds Number ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Gas Flow ◽  
Vacuum Chamber ◽  
Volumetric Mass Transfer Coefficient ◽  
Gas Flow Rate ◽  
Rh Process ◽  
Kinetics Of

The RH process is a secondary refining process that can simultaneously attain significant levels of removal of interstitial elements, such as carbon, nitrogen and hydrogen, from liquid steel. In the RH process, the decarburization rate plays a very important role in determining the productivity of the equipment. The kinetics of this reaction is controlled by mass transfer in the liquid phase. In the present work, a physical model of a RH degasser has been built and used in the study of the kinetics of decarburization. The effects of the gas flow rate and of the configurations of the nozzles used in the injection of the gas have been analyzed. The decarburization reaction of liquid steel was simulated using a reaction involving CO2 and caustic solutions. The concentration of CO2 in the solution was evaluated using pH measurements. Based on the experimental results, it was possible to estimate the reaction rate constant. A volumetric mass transfer coefficient was then calculated based on these rate constants and on the circulation rate of the liquid. The logarithm of the mass transfer coefficient showed a linear relationship with the logarithm of the gas flow rate. The slope of the line was found to vary according to the relevance of the reaction at the free surface in the vacuum chamber. A linear relationship between the volumetric mass transfer coefficient and the nozzle Reynolds number was also observed. The slopes of the lines changed according to the relative importance of the two reaction sites, gas-liquid interface in the upleg snorkel and in the vacuum. At higher Reynolds number, the reaction in the vacuum chamber tends to be more significant.

Sign in / Sign up

Export Citation Format

Share Document