Performance of the Solid Oxide Fuel Cell (SOFC)/Proton-Exchange Membrane Fuel Cell (PEMFC) Hybrid System

2016 ◽  
Vol 39 (4) ◽  
pp. 689-698 ◽  
Author(s):  
Ling Jun Tan ◽  
Chen Yang ◽  
Nana Zhou
Keyword(s):  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Hybrid System ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Exchange Membrane

Thermoeconomic Optimization of a Solid Oxide Fuel Cell and Proton Exchange Membrane Fuel Cell Hybrid Power System

2013 ◽  
Vol 11 (1) ◽  
Author(s):  
Ling Jun Tan ◽  
Chen Yang ◽  
Nana Zhou
Keyword(s):  
Sensitivity Analysis ◽  
Fuel Cell ◽  
Hybrid System ◽  
Life Cycle Cost ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Electrical Efficiency ◽  
Exchange Membrane

A hybrid system that combines a solid oxide fuel cell (SOFC) with a proton exchange membrane fuel cell (PEMFC) is presented in this paper. The SOFC stack acts as both an electricity producer and the fuel reformer for the PEMFC stack to generate additional power. A thermoeconomic model for the design optimization of a 220 kW SOFC-PEMFC hybrid system is developed in this work. Optimization of two objectives, i.e., the life cycle cost and the net electrical efficiency, are considered individually to find the optimum system configuration and component designs. Then, a multiparameter sensitivity analysis is performed to estimate the relative importance of the decision variables on the objectives. The optimization results indicate that the life cycle cost of the hybrid system is 3800–5,600 $/kW, and the maximum net electrical efficiency can reach around 63%, which is higher than an SOFC-only system, a reformer-PEMFC system, and an SOFC-gas turbine (GT) system with a similar output power. The sensitivity analysis shows that minimizing the size of the SOFC is most crucial to the system cost optimization. The hydrogen utilization factor in the SOFC is found to be sensitive to the net electrical efficiency.

Optimum Performance of a Regenerative Gas Turbine Power Plant Operating With/Without a Solid Oxide Fuel Cell

2011 ◽  
Vol 8 (5) ◽  
Author(s):  
Y. Haseli
Keyword(s):  
Fuel Cell ◽  
Pressure Drop ◽  
Solid Oxide Fuel Cell ◽  
Hybrid System ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Solid Oxide ◽  
Work Output ◽  
Oxide Fuel ◽  
Optimum Pressure

Optimum pressure ratios of a regenerative gas turbine (RGT) power plant with and without a solid oxide fuel cell are investigated. It is shown that assuming a constant specific heat ratio throughout the RGT plant, explicit expressions can be derived for the optimum pressure ratios leading to maximum thermal efficiency and maximum net work output. It would be analytically complicated to apply the same method for the hybrid system due to the dependence of electrochemical parameters such as cell voltage on thermodynamic parameters like pressure and temperature. So, the thermodynamic optimization of this system is numerically studied using models of RGT plant and solid oxide fuel cell. Irreversibilities in terms of component efficiencies and total pressure drop within each configuration are taken into account. The main results for the RGT plant include maximization of the work output at the expenses of 2–4% lower thermal efficiency and higher capital costs of turbo-compressor compared to a design based on maximum thermal efficiency. On the other hand, the hybrid system is studied for a turbine inlet temperature (TIT) of 1 250–1 450 K and 10–20% total pressure drop in the system. The maximum thermal efficiency is found to be at a pressure ratio of 3–4, which is consistent with past studies. A higher TIT leads to a higher pressure ratio; however, no significant effect of pressure drop on the optimum pressure ratio is observed. The maximum work output of the hybrid system may take place at a pressure ratio at which the compressor outlet temperature is equal to the turbine downstream temperature. The work output increases with increasing the pressure ratio up to a point after which it starts to vary slightly. The pressure ratio at this point is suggested to be the optimal because the work output is very close to its maximum and the thermal efficiency is as high as a littler less than 60%.

Design and Performance Study of a Solid Oxide Fuel Cell and Gas Turbine Hybrid System Applied in Combined Cooling, Heating, and Power System

2012 ◽  
Vol 138 (4) ◽  
pp. 205-214 ◽  
Author(s):  
Hsiao-Wei D. Chiang ◽  
Chih-Neng Hsu ◽  
Wu-Bin Huang ◽  
Chien-Hsiung Lee ◽  
Wei-Ping Huang ◽  
...  
Keyword(s):  
Fuel Cell ◽  
Power System ◽  
Solid Oxide Fuel Cell ◽  
Gas Turbine ◽  
Hybrid System ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Performance Study ◽  
And Performance ◽  
Combined Cooling
Sign in / Sign up

Export Citation Format

Share Document