Application of Response Surface Methodology for Optimization of Wheat Flour Milling Process

2021 ◽  
Author(s):  
John Kalitsis ◽  
Budiman Minasny ◽  
Ken Quail ◽  
Alexander McBratney
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Wheat Flour ◽  
Milling Process ◽  
Flour Milling ◽  
Wheat Flour Milling

Using the breakage matrix approach for monitoring the break release in the wheat flour milling process

2016 ◽  
Vol 97 (7) ◽  
pp. 2205-2214
Author(s):  
Nemanja Bojanić ◽  
Aleksandar Fišteš ◽  
Dušan Rakić ◽  
Aleksandar Takači ◽  
Tatjana Došenović
Keyword(s):  
Wheat Flour ◽  
Milling Process ◽  
Matrix Approach ◽  
Flour Milling ◽  
Wheat Flour Milling

scholarly journals Comparative analysis of milling results on the tail-end reduction passages of the wheat flour milling process: Conventional vs. eight-roller milling system

2015 ◽  
Vol 69 (4) ◽  
pp. 395-403
Author(s):  
Aleksandar Fistes
Keyword(s):  
Wheat Flour ◽  
Milling Process ◽  
Ash Content ◽  
Roller Mill ◽  
Flour Milling ◽  
Yield And Quality ◽  
Flour Yield ◽  
Wheat Flour Milling ◽  
Roller Milling ◽  
Roll Gap

Introduction of the eight-roller mill into the wheat flour milling process significantly reduces the investment costs and overall energy requirements compared to the conventional milling system. However, the conditions for controlled milling are less favorable and could result in deterioration of flour yield and quality. Paper compares milling results obtained using a conventional process and process with an eight-roller mill employed on the tail-end passages of the reduction system. At the same roll gap and under the same sieving conditions, the flour release was lower in the process with the eight-roller mill compared to the conventional milling system. By decreasing the roll gap and increasing the upper size limit (granulation) of flour in the process with the eight-roller mill it is possible to increase flour yield and decrease milling energy consumption per unit mass of flour produced. This can be achieved without deterioration of flour quality as determined by ash content.

scholarly journals Measurement and optimization of cutting forces during M200 TS milling process using the response surface methodology and dynamometer

Procedia CIRP ◽  
2020 ◽  
Vol 88 ◽  
pp. 288-293 ◽  
Author(s):  
I.A. Daniyan ◽  
I. Tlhabadira ◽  
O.O. Daramola ◽  
S.N. Phokobye ◽  
M. Siviwe ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Cutting Forces ◽  
Milling Process

The impact of transportation rates on the location of the wheat flour milling industry

Agribusiness ◽  
1985 ◽  
Vol 1 (1) ◽  
pp. 61-71 ◽  
Author(s):  
Michael W. Babcock ◽  
Gail L. Cramer ◽  
William A. Nelson
Keyword(s):  
Wheat Flour ◽  
Flour Milling ◽  
Wheat Flour Milling ◽  
The Impact

scholarly journals Control of the size and compositional distributions in a milling process by using a reverse breakage matrix approach

2021 ◽  
pp. 4-4
Author(s):  
Nemanja Bojanic ◽  
Aleksandar Fistes ◽  
Tatjana Dosenovic ◽  
Aleksandar Takaci ◽  
Mirjana Brdar ◽  
...  
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Milling Process ◽  
Matrix Approach ◽  
Flour Milling ◽  
Input And Output ◽  
Input Material ◽  
Compositional Distribution ◽  
Wheat Flour Milling

A method based on the reverse breakage matrix approach is proposed for controlling the effects that milling has on the particle size distribution and composition of the comminuted material. Applicability, possibilities, and limitations of the proposed method are tested on examples related to the process of wheat flour milling. It has been shown that the reverse matrix approach can be successfully used for defining the particle size distribution of the input material leading to the desired, predetermined particle size and compositional distribution in the output material. Moreover, we have illustrated that it is possible to simultaneously control both, input and output particle size distribution, together with the composition of the output material.

Sign in / Sign up

Export Citation Format

Share Document