Plasticization of poly(3‐hydroxybutyrate) with triethyl citrate: Thermal and mechanical properties, morphology, and kinetics of crystallization

2020 ◽  
Vol 138 (10) ◽  
pp. 49990
Author(s):  
Rodrigo T. Umemura ◽  
Maria Isabel Felisberti
Keyword(s):  
Mechanical Properties ◽  
Thermal And Mechanical Properties ◽  
Kinetics Of Crystallization ◽  
Triethyl Citrate ◽  
Kinetics Of

scholarly journals Studies on Sheet Explosive Formulation Based on Octahydro-1,3,5,7-Tetranitro-1,3,5,7-Tetrazocine and Hydroxyl Terminated Polybutadiene

2017 ◽  
Vol 67 (6) ◽  
pp. 617 ◽  
Author(s):  
Suresh Kumar Jangid ◽  
Mrityunjay Kumar Singh ◽  
Vasant Jadavji Solanki ◽  
Rabindra Kumar Sinha ◽  
Krothapalli Prabhakara Subrahmania Murthy
Keyword(s):  
Mechanical Properties ◽  
Activation Energy ◽  
Differential Scanning Calorimetry ◽  
Kinetic Method ◽  
Decomposition Kinetics ◽  
Thermal And Mechanical Properties ◽  
Binder System ◽  
Scanning Calorimetry ◽  
Velocity Of Detonation ◽  
Kinetics Of

<p class="p1">The effect of replacing hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) by octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) in HTPB-binder on the performance, sensitivity, thermal, and mechanical properties of the sheet explosive formulation has been studied. The maximum loading of HMX was achieved up to 78 per cent in HTPB-binder system. The velocity of detonation (VOD) of HMX-based sheet explosive was observed about 7300 m/s which is marginally higher than existing RDX-based sheet explosive formulation (RDX/HTPB-binder, 80/20). The VOD trends were verified by theoretical calculation by BKW code using FORTRAN executable program. The thermal decomposition kinetics of sheet explosive formulations was investigated by differential scanning calorimetry. The activation energy for sheet explosive formulation HMX/HTPB-binder (78/22) was calculated using Kissinger kinetic method and found to be 170.08 kJ/mol, infer that sheet explosive formulation is thermally stable.</p>

Reordering and Crystallization of Silicon Carbide Amorphized by Neutron Irradiation

2000 ◽  
Vol 650 ◽  
Author(s):  
Lance L. Snead ◽  
Martin Balden
Keyword(s):  
Thin Film ◽  
Silicon Carbide ◽  
Crystallization Kinetics ◽  
Neutron Irradiation ◽  
Onset Temperature ◽  
Kinetics Of Crystallization ◽  
Crystallization Onset Temperature ◽  
Crystallization Onset ◽  
Kinetics Of

ABSTRACTDensification and crystallization kinetics of bulk SiC amorphized by neutron irradiation is studied. The temperature of crystallization onset of this highly pure, fully amorphous bulk SiC was found to be between 875-885°C and crystallization is nearly complete by 950°C. In-situ TEM imaging confirms the onset of crystallization, though thin-film effects apparently alter the kinetics of crystallization above this temperature. It requires >1125°C for complete crystallization of the TEM foil. Annealing at temperatures between the irradiation and crystallization onset temperature is seen to cause significant densification attributed to a relaxation, or reordering, of the as-amorphized structure.

Elaboration and Characterization of the Properties of Refractory Cr Base Alloys

2010 ◽  
Vol 72 ◽  
pp. 46-52 ◽  
Author(s):  
Laurent Royer ◽  
Stéphane Mathieu ◽  
Christophe Liebaut ◽  
Pierre Steinmetz
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Molten Glass ◽  
Energy Production ◽  
Creep Properties ◽  
Refractory Alloys ◽  
Industrial Use ◽  
Kinetics Of ◽  
Selection Of

For energy production and also for the glass industry, finding new refractory alloys which could permit to increase the process temperatures to 1200°C or more is a permanent challenge. Chromium base alloys can be good candidates, considering the melting point of Cr itself, and also its low corrosion rate in molten glass. Two families of alloys have been studied for this purpose, Cr-Mo-W and Cr-Ta-X alloys (X= Mo, Si..). A finer selection of compositions has been done, to optimize their chemical and mechanical properties. Kinetics of HT oxidation by air, of corrosion by molten glass and also creep properties of several alloys have been measured up to 1250°C. The results obtained with the best alloys (Cr-Ta base) give positive indications as regards the possibility of their industrial use.

Polyamides containing a biorenewable aromatic monomer based on coumalate esters: from synthesis to evaluation of the thermal and mechanical properties

2021 ◽  
Vol 12 (16) ◽  
pp. 2379-2388
Author(s):  
Jules Stouten ◽  
Aleksandra A. Wróblewska ◽  
Glenn Grit ◽  
Jurrie Noordijk ◽  
Bert Gebben ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Propionic Acid ◽  
Terephthalic Acid ◽  
Thermal And Mechanical Properties ◽  
Aromatic Polyamides ◽  
Aromatic Monomer

A new biobased alternative for terephthalic acid (TPA) in (semi-)aromatic polyamides is proposed, namely 4-carboxybenzene propionic acid (4CBPA).

Sign in / Sign up

Export Citation Format

Share Document