3D‐printed polymer packing structures: Uniformity of morphology and mechanical properties via microprocessing conditions

2020 ◽  
Vol 137 (44) ◽  
pp. 49381 ◽  
Author(s):  
Sunghan Kim ◽  
Volodymyr F. Korolovych ◽  
Rachel L. Muhlbauer ◽  
Vladimir V. Tsukruk
Keyword(s):  
Mechanical Properties ◽  
3D Printed ◽  
Morphology And Mechanical Properties ◽  
Polymer Packing

Influence of slicing parameters on surface quality and mechanical properties of 3D-printed CF/PLA composites fabricated by FDM technique

2021 ◽  
pp. 1-18
Author(s):  
N. Vinoth Babu ◽  
N. Venkateshwaran ◽  
N. Rajini ◽  
Sikiru Oluwarotimi Ismail ◽  
Faruq Mohammad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Quality ◽  
3D Printed

scholarly journals Fabrication of Polycaprolactone/Nano Hydroxyapatite (PCL/nHA) 3D Scaffold with Enhanced In Vitro Cell Response via Design for Additive Manufacturing (DfAM)

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1394
Author(s):  
Yong Sang Cho ◽  
So-Jung Gwak ◽  
Young-Sam Cho
Keyword(s):  
Mechanical Properties ◽  
Cell Response ◽  
Structural Characteristics ◽  
Structure Design ◽  
Compressive Modulus ◽  
Control Group ◽  
Design For Additive Manufacturing ◽  
3D Scaffold ◽  
3D Printed

In this study, we investigated the dual-pore kagome-structure design of a 3D-printed scaffold with enhanced in vitro cell response and compared the mechanical properties with 3D-printed scaffolds with conventional or offset patterns. The compressive modulus of the 3D-printed scaffold with the proposed design was found to resemble that of the 3D-printed scaffold with a conventional pattern at similar pore sizes despite higher porosity. Furthermore, the compressive modulus of the proposed scaffold surpassed that of the 3D-printed scaffold with conventional and offset patterns at similar porosities owing to the structural characteristics of the kagome structure. Regarding the in vitro cell response, cell adhesion, cell growth, and ALP concentration of the proposed scaffold for 14 days was superior to those of the control group scaffolds. Consequently, we found that the mechanical properties and in vitro cell response of the 3D-printed scaffold could be improved by kagome and dual-pore structures through DfAM. Moreover, we revealed that the dual-pore structure is effective for the in vitro cell response compared to the structures possessing conventional and offset patterns.

Physical property of 3D-printed sinusoidal pattern using shape memory TPU filament

2020 ◽  
Vol 90 (21-22) ◽  
pp. 2399-2410 ◽  
Author(s):  
Shahbaj Kabir ◽  
Hyelim Kim ◽  
Sunhee Lee
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Shape Memory ◽  
Fused Deposition Modeling ◽  
Loss Modulus ◽  
Thermoplastic Polyurethane ◽  
Heating Process ◽  
Fused Deposition ◽  
3D Printed ◽  
Sinusoidal Pattern

This study has investigated the physical properties of 3D-printable shape memory thermoplastic polyurethane (SMTPU) filament and its 3D-printed sinusoidal pattern obtained by fused deposition modeling (FDM) technology. To investigate 3D filaments, thermoplastic polyurethane (TPU) and SMTPU filament were examined by conducting infrared spectroscopy, x-ray diffraction (XRD), dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and a tensile test. Then, to examine the 3D-printed sinusoidal samples, a sinusoidal pattern was developed and 3D-printed. Those samples went through a three-step heating process: (a) untreated state; (b) 5 min heating at 70°C, cooling for 30 min at room temperature; and (c) a repeat of step 2. The results obtained by the three different heating processes of the 3D-printed sinusoidal samples were examined by XRD, DMTA, DSC and the tensile test to obtain the effect of heating or annealing on the structural and mechanical properties. The results show significant changes in structure, crystallinity and thermal and mechanical properties of SMTPU 3D-printed samples due to the heating steps. XRD showed the increase in crystallinity with heating. In DMTA, storage modulus, loss modulus and the tan σ peak position also changed for various heating steps. The DSC result showed that the Tg for different steps of the SMTPU 3D-printed sample remained almost the same at around 51°C. The tensile property of the TPU 3D-printed sinusoidal sample decreased in terms of both load and elongation with increased heating processes, while for the SMTPU 3D-printed sinusoidal sample, the load decreased but elongation increased about 2.5 times.

Sign in / Sign up

Export Citation Format

Share Document