Effect of polyethylene glycol on mechanical properties of bamboo fiber‐reinforced polylactic acid composites

2019 ◽  
Vol 136 (26) ◽  
pp. 47709 ◽  
Author(s):  
Haibo Long ◽  
Zhiqiang Wu ◽  
Qianqian Dong ◽  
Yuting Shen ◽  
Wuyi Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polyethylene Glycol ◽  
Polylactic Acid ◽  
Bamboo Fiber ◽  
Fiber Reinforced

scholarly journals Preparation of Long Sisal Fiber-Reinforced Polylactic Acid Biocomposites with Highly Improved Mechanical Performance

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1124
Author(s):  
Zhifang Liang ◽  
Hongwu Wu ◽  
Ruipu Liu ◽  
Caiquan Wu
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Mechanical Performance ◽  
Tensile Elongation ◽  
Sisal Fiber ◽  
Fiber Reinforced ◽  
Impact Performance ◽  
The Matrix ◽  
Blending Process ◽  
Extension Direction

Green biodegradable plastics have come into focus as an alternative to restricted plastic products. In this paper, continuous long sisal fiber (SF)/polylactic acid (PLA) premixes were prepared by an extrusion-rolling blending process, and then unidirectional continuous long sisal fiber-reinforced PLA composites (LSFCs) were prepared by compression molding to explore the effect of long fiber on the mechanical properties of sisal fiber-reinforced composites. As a comparison, random short sisal fiber-reinforced PLA composites (SSFCs) were prepared by open milling and molding. The experimental results show that continuous long sisal fiber/PLA premixes could be successfully obtained from this pre-blending process. It was found that the presence of long sisal fibers could greatly improve the tensile strength of LSFC material along the fiber extension direction and slightly increase its tensile elongation. Continuous long fibers in LSFCs could greatly participate in supporting the load applied to the composite material. However, when comparing the mechanical properties of the two composite materials, the poor compatibility between the fiber and the matrix made fiber’s reinforcement effect not well reflected in SSFCs. Similarly, the flexural performance and impact performance of LSFCs had been improved considerably versus SSFCs.

Effect of Ceramic Fillers on Mechanical Properties of Bamboo Fiber Reinforced Epoxy Composites: A Comparative Study

2010 ◽  
Vol 123-125 ◽  
pp. 1031-1034 ◽  
Author(s):  
Sandhyarani Biswas ◽  
Alok Satapathy ◽  
Amar Patnaik
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Red Mud ◽  
Synergistic Effects ◽  
Bamboo Fiber ◽  
Industrial Wastes ◽  
Epoxy Composites ◽  
Void Content ◽  
Filler Materials ◽  
Fiber Reinforced

In order to obtain the favoured material properties for a particular application, it is important to know how the material performance changes with the filler content under given loading conditions. In this study, a series of bamboo fiber reinforced epoxy composites are fabricated using conventional filler (aluminium oxide (Al2O3) and silicon carbide (SiC) and industrial wastes (red mud and copper slag) particles as filler materials. By incorporating the chosen particulate fillers into the bamboo-fiber reinforced epoxy, synergistic effects, as expected are achieved in the form of modified mechanical properties. Inclusion of fiber in neat epoxy improved the load bearing capacity (tensile strength) and the ability to withstand bending (flexural strength) of the composites. But with the incorporation of particulate fillers, the tensile strengths of the composites are found to be decreasing in most of the cases. Among the particulate filled bamboo-epoxy composites, least value of void content are recorded for composites with silicon carbide filling and for the composites with glass fiber reinforcement minimum void fraction is noted for red mud filling. The effects of these four different ceramics on the mechanical properties of bamboo- epoxy composites are investigated and the conclusions drawn from the above investigation are discussed.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Experimental study on effect of fiber length and fiber content on tensile and flexural properties of bamboo fiber/epoxy composite

2019 ◽  
Vol 15 (5) ◽  
pp. 947-957 ◽  
Author(s):  
Giridharan R. ◽  
Raatan V.S. ◽  
Jenarthanan M.P.
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Epoxy Composite ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Fiber Content ◽  
Bamboo Fiber ◽  
Flexural Properties ◽  
Fiber Reinforced ◽  
Content Type

Purpose The purpose of this paper is to study the effects of fiber length and content on properties of E-glass and bamboo fiber reinforced epoxy resin matrices. Experiments are carried out as per ASTM standards to find the mechanical properties. Further, fractured surface of the specimen is subjected to morphological study. Design/methodology/approach Composite samples were prepared according to ASTM standards and were subjected to tensile and flexural loads. The fractured surfaces of the specimens were examined directly under scanning electron microscope. Findings From the experiment, it was found that the main factors that influence the properties of composite are fiber length and content. The optimum fiber length and weight ratio are 15 mm and 16 percent, respectively, for bamboo fiber/epoxy composite. Hence, the prediction of optimum fiber length and content becomes important, so that composite can be prepared with best mechanical properties. The investigation revealed the suitability of bamboo fiber as an effective reinforcement in epoxy matrix. Practical implications As bamboo fibers are biodegradable, recyclable, light weight and so on, their applications are numerous. They are widely used in automotive components, aerospace parts, sporting goods and building industry. With this scenario, the obtained result of bamboo fiber reinforced composites is not ignorable and could be of potential use, since it leads to harnessing of available natural fibers and their composites rather than synthetic fibers. Originality/value This work enlists the effect of fiber length and fiber content on tensile and flexural properties of bamboo fiber/epoxy composite, which has not been attempted so far.

Improved mechanical properties of the graphene oxide modified bamboo‐fiber‐reinforced polypropylene composites

2020 ◽  
Vol 41 (9) ◽  
pp. 3615-3626 ◽  
Author(s):  
Qianting Wang ◽  
Yu Zhang ◽  
Weikang Liang ◽  
Jianjie Wang ◽  
Youxin Chen
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Bamboo Fiber ◽  
Fiber Reinforced ◽  
Polypropylene Composites
Sign in / Sign up

Export Citation Format

Share Document