Damage growth-based constitutive model of satin weave composites under different temperatures and strain rates

2019 ◽  
Vol 136 (21) ◽  
pp. 47575 ◽  
Author(s):  
Xueyao Hu ◽  
Weiguo Guo ◽  
Jianjun Wang ◽  
Kangbo Yuan
Keyword(s):  
Constitutive Model ◽  
Strain Rates ◽  
Damage Growth ◽  
Different Temperatures

scholarly journals Dynamic Constitutive Model of Ultra-High Molecular Weight Polyethylene (UHMWPE): Considering the Temperature and Strain Rate Effects

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1561 ◽  
Author(s):  
Kebin Zhang ◽  
Wenbin Li ◽  
Yu Zheng ◽  
Wenjin Yao ◽  
Changfang Zhao
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Plastic Material ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Ballistic Performance ◽  
Stress Strain ◽  
Different Temperatures

The temperature and strain rate significantly affect the ballistic performance of UHMWPE, but the deformation of UHMWPE under thermo-mechanical coupling has been rarely studied. To investigate the influences of the temperature and the strain rate on the mechanical properties of UHMWPE, a Split Hopkinson Pressure Bar (SHPB) apparatus was used to conduct uniaxial compression experiments on UHMWPE. The stress–strain curves of UHMWPE were obtained at temperatures of 20–100 °C and strain rates of 1300–4300 s−1. Based on the experimental results, the UHMWPE belongs to viscoelastic–plastic material, and a hardening effect occurs once UHMWPE enters the plastic zone. By comparing the stress–strain curves at different temperatures and strain rates, it was found that UHMWPE exhibits strain rate strengthening and temperature softening effects. By modifying the Sherwood–Frost model, a constitutive model was established to describe the dynamic mechanical properties of UHMWPE at different temperatures. The results calculated using the constitutive model were in good agreement with the experimental data. This study provides a reference for the design of UHMWPE as a ballistic-resistant material.

A Phenomenological Constitutive Model Constructed for PC/ABS Blends

2006 ◽  
Vol 306-308 ◽  
pp. 989-994 ◽  
Author(s):  
M. Nizar Machmud ◽  
Masaki Omiya ◽  
Hirotsugu Inoue ◽  
Kikuo Kishimoto
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Constitutive Models ◽  
Strain Rates ◽  
Strain Behavior ◽  
Tension Tests ◽  
Proposed Model ◽  
Wide Range ◽  
Different Temperatures ◽  
Prediction Evaluation

Based on previous available constitutive models, a phenomenological constitutive model has been constructed and is proposed to describe the strain, strain rate and temperature dependentdeformation behavior of PC/ABS blends. In this paper, four quasi-static uniaxial tension tests of a specimen tested at different strain rates and temperatures were used to identify the constitutive model constants. By using the proposed constitutive model, predicting the stress-strain behavior of the PC/ABS blend tested at certain strain rate and different temperatures compares well to the behavior exhibited from the tests. From comparison between the DSGZ and the proposed models, proposed model shows a better prediction. Evaluation of the proposed constitutive model was also presented and it has revealed that the proposed model might have a potential to be used for predicting a wide range of temperatures and high strain rates behavior of PC/ABS blends.

A Thermovisco-Hyperelastic Constitutive Model of NEPE Propellant Over a Large Range of Strain Rates

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Junfa Zhang ◽  
Jian Zheng ◽  
Xiong Chen ◽  
Chaoxiang Sun ◽  
Jinsheng Xu
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Large Range ◽  
Testing Machine ◽  
Experimental Results ◽  
Strain Rates ◽  
Static State ◽  
Rate Dependent ◽  
Different Temperatures ◽  
Nepe Propellant

The uniaxial compressive mechanical curves of nitrate ester plasticized polyether (NEPE) propellant under different temperatures and strain rates have been obtained with a universal testing machine and modified split Hopkinson pressure bar (SHPB). The experimental results show that the mechanical properties of NEPE propellant are both rate dependent and temperature dependent. With decreasing temperature or increasing strain rate, the modulus and rigidity obviously increase. Based on the previous models proposed by Yang and Pouriayevali, we propose a modified viscohyperelastic constitutive model which can describe the mechanical response over a large range of strain rates. Then we add a rate-dependent temperature item into the modified model to make a thermovisco-hyperelastic constitutive model. By comparing the experimental results with the model, we find that the thermovisco-hyperelastic constitutive model can correctly describe the uniaxial compressive mechanical properties of NEPE propellant at different temperatures and over a large range of strain rates from the static state to 4500 s−1.

Critical damage value of AZ31B magnesium alloy with different temperatures and strain rates

Rare Metals ◽  
2015 ◽  
Author(s):  
Jing-Ren Dong ◽  
Ding-Fei Zhang ◽  
Yu-Feng Dong ◽  
Fu-Sheng Pan ◽  
Sen-Sen Chai
Keyword(s):  
Magnesium Alloy ◽  
Strain Rates ◽  
Az31b Magnesium Alloy ◽  
Different Temperatures ◽  
Critical Damage

A Method for Predicting the Behavior of Plastics at Different Temperatures

2014 ◽  
Vol 1039 ◽  
pp. 107-111
Author(s):  
Yang Chen ◽  
Gui Qin Li ◽  
Bin Ruan ◽  
Xiao Yuan ◽  
Hong Bo Li
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Constitutive Model ◽  
Research And Development ◽  
Mechanical Behavior ◽  
Plastic Material ◽  
Different Temperatures ◽  
Plastic Parts

The mechanical behavior of plastic material is dramatically sensitive to temperature. An method is proposed to predict the mechanical behavior of plastics for cars, ranging from low-temperature low temperature ≤-40°C to high temperature ≥80°C. It dominates the behavior of plastic material based on improved constitutive model in which the parameters adjusted by a series of tests under different temperatures. The method is validated with test and establishes the basis for research and development of plastic parts for automobile as well.

Constitutive Modeling for Elevated Temperature Flow Behavior of ZHMn34-2-2-1 Manganese Brass

2017 ◽  
Vol 872 ◽  
pp. 30-37
Author(s):  
Meng Han Wang ◽  
Kang Wei ◽  
Xiao Juan Li
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Flow Behavior ◽  
Peak Stress ◽  
Strain Rates ◽  
Hollomon Parameter ◽  
Prediction Ability ◽  
Absolute Relative Error ◽  
Deformation Behaviors ◽  
State Stress

The hot compressive deformation behaviors of ZHMn34-2-2-1 manganese brass are investigated on Thermecmastor-Z thermal simulator over wide processing domain of temperatures (923K-1073K) and strain rates (0.01s-1-10s-1). The true stress-strain curves exhibit a single peak stress, after which the stress monotonously decreases until a steady state stress occurs, indicating a typical dynamic recrystallization. A revised constitutive model coupling flow stress with strain, strain rate and deformation temperature is established with the material constants expressed by polynomial fitting of strain. Moreover, better prediction ability of the constitutive model is achieved by implementation of a simple approach for modified the Zener-Hollomon parameter considering the compensation of strain rate and temperature increment. By comparing the predicted and experimented values, the correlation coefficient and mean absolute relative error are 0.997 and 2.363%, respectively. The quantitative statistical results indicate that the proposed constitutive model can precisely characterize the hot deformation behavior of ZHMn34-2-2-1 manganese brass.

Thermomechanical Response of Commercially Pure Titanium under Large Plastic Deformation at High Strain Rates

2012 ◽  
Vol 548 ◽  
pp. 174-178 ◽  
Author(s):  
Chong Yang Gao ◽  
Wei Ran Lu
Keyword(s):  
Pure Titanium ◽  
Optimal Solution ◽  
Optimization Method ◽  
Strain Rates ◽  
Commercially Pure Titanium ◽  
Thermomechanical Response ◽  
Commercially Pure ◽  
Different Temperatures ◽  
Cp Ti ◽  
Constitutive Parameters

By using a dislocation-based plastic constitutive model for hcp metals developed by us recently, the dynamic thermomechanical response of an important industrial material, commercially pure titanium (CP-Ti), was described at different temperatures and strain rates. The constitutive parameters of the material are determined by an efficient optimization method for a globally optimal solution. The model can well predict the dynamic response of CP-Ti by the comparison with experimental data and the Nemat-Nasser-Guo model.

Parameters Identification of Johnson-Cook Constitutive Equation for Aluminum Brass

2014 ◽  
Vol 887-888 ◽  
pp. 1032-1035 ◽  
Author(s):  
Chang Chun Di ◽  
Kai Bo Cui ◽  
Jun Qi Qin ◽  
Da Lin Wu
Keyword(s):  
Testing Machine ◽  
Strain Curve ◽  
High Strength ◽  
Dynamic Mechanical Properties ◽  
Model Parameters ◽  
Strain Rates ◽  
Stress Strain Curve ◽  
Method Of Least Squares ◽  
Different Temperatures ◽  
Split Hopkinson

Aluminum brass HAL66-6-3-2 is abrasion-resistant alloy with high strength, hardness and wear resistance, corrosion resistance is also well, commonly used in the field of marine and ordnance industry. The quasi static and dynamic mechanical properties were tested through the use of electronic universal testing machine and Split Hopkinson Tension Bar (SHTB). Meanwhile, the material stress-strain curve at different temperatures and different strain rates is also obtained. Based on Johnson-Cook constitutive model, using the method of least squares fitting the experimental data to determine the model parameters, fitting and experimental results agree well.

scholarly journals Extension of Flow Behaviour and Damage Models for Cast Iron Alloys with Strain Rate Effect

2020 ◽  
Author(s):  
Chuang Liu ◽  
Dongzhi Sun ◽  
Xianfeng Zhang ◽  
Florence Andrieux ◽  
Tobias Gerster
Keyword(s):  
Cast Iron ◽  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Damage Model ◽  
Iron Alloys ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Damage Models ◽  
Rate Dependent

Abstract Cast iron alloys with low production cost and quite good mechanical properties are widely used in the automotive industry. To study the mechanical behavior of a typical ductile cast iron (GJS-450) with nodular graphite, uni-axial quasi-static and dynamic tensile tests at strain rates of 10− 4, 1, 10, 100, and 250 s− 1 were carried out. In order to investigate the effects of stress state, specimens with various geometries were used in the experiments. Stress–strain curves and fracture strains of the GJS-450 alloy in the strain-rate range of 10− 4 to 250 s− 1 were obtained. A strain rate-dependent plastic flow law based on the Voce model is proposed to describe the mechanical behavior in the corresponding strain-rate range. The deformation behavior at various strain rates is observed and analyzed through simulations with the proposed strain rate-dependent constitutive model. The available damage model from Bai and Wierzbicki is extended to take the strain rate into account and calibrated based on the analysis of local fracture strains. The validity of the proposed constitutive model including the damage model was verified by the corresponding experimental results. The results show that the strain rate has obviously nonlinear effects on the yield stress and fracture strain of GJS-450 alloys. The predictions with the proposed constitutive model and damage models at various strain rates agree well with the experimental results, which illustrates that the rate-dependent flow rule and damage models can be used to describe the mechanical behavior of cast iron alloys at elevated strain rates.

Sign in / Sign up

Export Citation Format

Share Document