Sorption characteristic of organic liquid and its effect on the mechanical performance of a PLA-based plastic

2016 ◽  
Vol 133 (20) ◽  
pp. n/a-n/a ◽  
Author(s):  
Indah Widiastuti ◽  
Igor Sbarski ◽  
SH Masood
Keyword(s):  
Mechanical Performance ◽  
Organic Liquid ◽  
Sorption Characteristic

The Mechanical Performance of Carbon Fibres- Addressing the Role of Microstructure

2019 ◽  
Author(s):  
Peter Peter ◽  
Claudia Creighton ◽  
David Fox ◽  
Pablo Mota Santiago ◽  
Adrian Hawley ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
Carbon Fibres

Microstructural and Mechanical Behaviour Evaluation of Mg-Al-Zn Alloy Friction Stir Welded Joint

2020 ◽  
Vol 17 (3) ◽  
pp. 8150-8159
Author(s):  
Kulwant Singh ◽  
Gurbhinder Singh ◽  
Harmeet Singh
Keyword(s):  
Heat Treatment ◽  
Friction Stir Welding ◽  
Magnesium Alloys ◽  
Mechanical Performance ◽  
Fuel Efficiency ◽  
Research Work ◽  
Grain Structure ◽  
Tensile Fracture ◽  
Friction Stir ◽  
The Impact

The weight reduction concept is most effective to reduce the emissions of greenhouse gases from vehicles, which also improves fuel efficiency. Amongst lightweight materials, magnesium alloys are attractive to the automotive sector as a structural material. Welding feasibility of magnesium alloys acts as an influential role in its usage for lightweight prospects. Friction stir welding (FSW) is an appropriate technique as compared to other welding techniques to join magnesium alloys. Field of friction stir welding is emerging in the current scenario. The friction stir welding technique has been selected to weld AZ91 magnesium alloys in the current research work. The microstructure and mechanical characteristics of the produced FSW butt joints have been investigated. Further, the influence of post welding heat treatment (at 260 °C for 1 h) on these properties has also been examined. Post welding heat treatment (PWHT) resulted in the improvement of the grain structure of weld zones which affected the mechanical performance of the joints. After heat treatment, the tensile strength and elongation of the joint increased by 12.6 % and 31.9 % respectively. It is proven that after PWHT, the microhardness of the stir zone reduced and a comparatively smoothened microhardness profile of the FSW joint obtained. No considerable variation in the location of the tensile fracture was witnessed after PWHT. The results show that the impact toughness of the weld joints further decreases after post welding heat treatment.

Removal of nutrients from Organic Liquid Agricultural Waste using filamentous algae.

2020 ◽  
Author(s):  
Gonzalo Flores-Morales ◽  
Mónica Díaz ◽  
Patricia Arancibia-Avila ◽  
Michelle Muñoz-Carrasco ◽  
Pamela Jara-Zapata ◽  
...  
Keyword(s):  
Organic Waste ◽  
Low Cost ◽  
Organic Liquid ◽  
Agricultural Waste ◽  
Filamentous Algae ◽  
Tertiary Treatment ◽  
Nutrient Reduction ◽  
Algae Removal ◽  
Algae Growth ◽  
Waste Effluents

Abstract A feasibility analysis of tertiary treatment for Organic Liquid Agricultural Waste is presented using filamentous algae belonging to the genus Cladophora sp. as an alternative to chemical tertiary treatment. The main advantages of tertiary treatments that use biological systems are the low cost investment and the minimal dependence on environmental variables. In this work we demonstrate that filamentous algae reduces the nutrient load of nitrate (circa 75%) and phosphate (circa 86%) from the organic waste effluents coming from dairy farms after nine days of culture, with the added advantage being that after the treatment period, algae removal can be achieved by simple procedures. Currently, the organic wastewater is discarded into fields and local streams. However, the algae can acquire value as a by-product since it has various uses as compost, cellulose, and biogas. A disadvantage of this system is that clean water must be used to achieve enough water transparency to allow algae growth. Even so, the nutrient reduction system of the organic effluents proposed is friendly to the ecosystem, compared to tertiary treatments that use chemicals to precipitate and collect nutrients such as nitrates and phosphates.

NUMERICAL STUDY ON THE MECHANICAL PERFORMANCE OF GRAPHENE BRIDGES ON SILLICON THIN FILM TRANSISTORS

2011 ◽  
Author(s):  
Byung-Jae Kim ◽  
Hyeon-Seok Seo ◽  
Won-Ho Lee ◽  
Jong-Hyun Ahn ◽  
Youn-Jea Kim
Keyword(s):  
Thin Film ◽  
Thin Film Transistors ◽  
Mechanical Performance ◽  
Numerical Study

Effect of tolbutamide on myocardial metabolism and mechanical performance of the diabetic rat

Diabetes ◽  
1984 ◽  
Vol 33 (12) ◽  
pp. 1138-1143 ◽  
Author(s):  
B. H. Tan ◽  
G. L. Wilson ◽  
S. W. Schaffer
Keyword(s):  
Myocardial Metabolism ◽  
Mechanical Performance ◽  
Diabetic Rat
Sign in / Sign up

Export Citation Format

Share Document