Influence of carbon black on decompression failure and hydrogen permeation properties of filled ethylene-propylene-diene-methylene rubbers exposed to high-pressure hydrogen gas

2011 ◽  
Vol 122 (5) ◽  
pp. 3172-3187 ◽  
Author(s):  
Junichiro Yamabe ◽  
Shin Nishimura
Keyword(s):  
High Pressure ◽  
Carbon Black ◽  
Hydrogen Permeation ◽  
Hydrogen Gas ◽  
Ethylene Propylene ◽  
Permeation Properties ◽  
Pressure Hydrogen

scholarly journals Gas chromatography techniques to evaluate the hydrogen permeation characteristics in rubber: ethylene propylene diene monomer

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jae Kap Jung ◽  
In Gyoo Kim ◽  
Ki Soo Chung ◽  
Un Bong Baek
Keyword(s):  
Gas Chromatography ◽  
Carbon Black ◽  
Hydrogen Diffusion ◽  
Hydrogen Permeation ◽  
Gas Permeability ◽  
Hydrogen Gas ◽  
Ex Situ ◽  
Ethylene Propylene Diene Monomer ◽  
Ethylene Propylene ◽  
Diffusion Analysis

AbstractWe established an ex-situ technique for evaluating hydrogen gas permeability by thermal desorption analysis (TDA) gas chromatography (GC) and by self-developed diffusion analysis software. Absorbed hydrogen mass in rubber, related to the GC-peak area, is recorded as a function of elapsed time after decompressing the hydrogen under high-pressure. From the charging amount (CH0) and diffusivity (D) obtained by the developed diffusion analysis program, the solubility(S) and permeability(P) is evaluated via Henry’s law and P = SD, respectively. The techniques were applied to ethylene propylene diene monomer (EPDM) rubber, sealing material candidates in hydrogen infrastructures. EPDM sample mixed with carbon black fillers showed dual hydrogen diffusion behaviors, whereas EPDM sample without carbon black showed a single hydrogen diffusion behavior. There was no appreciable pressure or size dependence on D, S and P. P are consistent with that measured by different researcher within the expanded uncertainty.

scholarly journals Proposal of Design Method Enabling Cr-Mo Steels to be Used in High-Pressure Hydrogen Gas Environment

Hyomen Kagaku ◽  
2015 ◽  
Vol 36 (11) ◽  
pp. 562-567
Author(s):  
Hisao MATSUNAGA ◽  
Junichiro YAMABE ◽  
Saburo MATSUOKA
Keyword(s):  
High Pressure ◽  
Design Method ◽  
Hydrogen Gas ◽  
Gas Environment ◽  
Pressure Hydrogen

Crack Growth Analysis of High-Pressure Equipment for Hydrogen Storage

2013 ◽  
Author(s):  
Z. Y. Li ◽  
C. L. Zhou ◽  
Y. Z. Zhao ◽  
Z. L. Hua ◽  
L. Zhang ◽  
...  
Keyword(s):  
High Pressure ◽  
Hydrogen Storage ◽  
Crack Growth ◽  
Growth Analysis ◽  
Model Material ◽  
Hydrogen Gas ◽  
Cycle Life ◽  
Cold Worked ◽  
Type 304 ◽  
Pressure Hydrogen

Crack growth analysis (CGA) was applied to estimate the cycle life of the high-pressure hydrogen equipment constructed by the practical materials of 4340 (two heats), 4137, 4130X, A286, type 316 (solution-annealed (SA) and cold-worked (CW)), and type 304 (SA and CW) in 45, 85 and 105 MPa hydrogen and air. The wall thickness was calculated following five regulations of the High Pressure Gas Safety Institute of Japan (KHK) designated equipment rule, KHKS 0220, TSG R0002, JB4732, and ASME Sec. VIII, Div. 3. We also applied CGA for four typical model materials to discuss the effect of ultimate tensile strength (UTS), pressure and hydrogen sensitivity on the cycle life of the high-pressure hydrogen equipment. Leak before burst (LBB) was confirmed in all practical materials in hydrogen and air. The minimum KIC required for LBB of the model material with UTS of even 1500 MPa was 170 MPa·m0.5 in 105 MPa. Cycle life qualified 103 cycles for all practical materials in air. In 105 MPa hydrogen, the cycle life by KIH was much shorter than that in air for two heats of 4340 and 4137 sensitive to hydrogen gas embrittlement (HGE). The cycle life of type 304 (SA) sensitive to HGE was almost above 104 cycles in hydrogen, while the cycle life of type 316 (SA and CW) was not affected by hydrogen and that of A286 in hydrogen was near to that in air. It was discussed that the cycle life increased with decreasing pressure or UTS in hydrogen. This behavior was due to that KIH increased or fatigue crack growth (FCG) decreased with decreasing pressure or UTS. The cycle life data of the model materials under the conditions of the pressure, UTS, KIH, FCG and regulations in both hydrogen and air were proposed quantitatively for materials selection for high-pressure hydrogen storage.

Sign in / Sign up

Export Citation Format

Share Document