Engineering the friction-and-wear behavior of polyelectrolyte multilayer nanoassemblies through block copolymer surface capping, metallic nanoparticles, and multiwall carbon nanotubes

2004 ◽  
Vol 92 (1) ◽  
pp. 439-448 ◽  
Author(s):  
Prem V. Pavoor ◽  
Brian P. Gearing ◽  
Russell E. Gorga ◽  
Anuj Bellare ◽  
Robert E. Cohen
Keyword(s):  
Carbon Nanotubes ◽  
Block Copolymer ◽  
Metallic Nanoparticles ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Multiwall Carbon Nanotubes ◽  
Polyelectrolyte Multilayer ◽  
Friction And Wear Behavior ◽  
Surface Capping ◽  
Multiwall Carbon

Influence of MoS2, H3BO3, and MWCNT Additives on the Dry and Lubricated Sliding Tribology of AMMC–Steel Contacts

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Harpreet Singh ◽  
ParamPreet Singh ◽  
Hiralal Bhowmick
Keyword(s):  
Carbon Nanotubes ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Preliminary Investigation ◽  
Multiwall Carbon Nanotubes ◽  
Operating Conditions ◽  
Matrix Composites ◽  
Base Oil ◽  
Oil Additives ◽  
Multiwall Carbon

The present study is focused on the performance evaluation of MoS2, H3BO3, and multiwall carbon nanotubes (MWCNT) used as the potential oil additives in base oil for aluminum metal matrix composites (AMMC)–steel (EN31) tribocontact. Al–B4C composite is used for this purpose; based on a set of preliminary investigation under unlubricated and fresh oil lubrication, three different types of AMMCs (Al–SiC, Al–B4C, and Al–SiC–B4C) were used. A pin-on-disk tribometer is used for all the friction and wear tests under operating condition of load 9.8 N and sliding velocity of 0.5 m/s. From the particle-based wet tribology, it is clear that both the additives H3BO3 and MWCNT improve the friction as well as wear behavior for selected composite contacts. Multiwall carbon nanotubes emerged out as superior among all the additives, whereas MoS2 additives show marginal enhancement in frictional performance under given operating conditions. Fractography and morphological study of pin specimens are carried out to identify the underlying friction and wear mechanisms.

Wear Behavior of Polyester – Carbon Nanotubes Composites under Dry Sliding Ball-on-Flat Reciprocating Test

2015 ◽  
Vol 809-810 ◽  
pp. 1169-1174
Author(s):  
Adrian Cotet ◽  
Luminita Ciupagea ◽  
Dumitru Dima ◽  
Gabriel Andrei
Keyword(s):  
Carbon Nanotubes ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Behavior ◽  
Multiwall Carbon Nanotubes ◽  
Dry Sliding ◽  
Linear Wear ◽  
Linear Wear Rate ◽  
Multiwall Carbon

Friction coefficient and linear wear rate of polyester-carbon nanotubes composites were investigated through ball-on-flat reciprocating test, under dry sliding contact. Three types of nanoscopic fillers were used: multiwall carbon nanotubes (MWCNT), functionalized multiwall carbon nanotubes (MWCNT-COOH) and singlewall carbon nanotubes (SWCNT), with three values of weight content 0.1, 0.15 and 0.2 wt%. Comparative analysis was done for polyester and its composites tested over 14 m sliding distance, under three values of load, 30 N, 40 N and 50 N. Composites containing MWCNT underwent a decrease in friction coefficient and linear wear rate only in case of 50N loading. An improvement of wear behavior under 50N loading was obtained for the composite with 0.10 wt% functionalized carbon nanotubes. Generally, better values of wear rate at 50 N loading were recorded in case of composites with 0.15 wt% and 0.20 wt% MWCNT and SWCNT, respectively. Optical and electronic investigation of the worn surfaces revealed the occurrence of abrasive, adhesive and fatigue wear. Abrasive wear is due to the hard particles detached from the counterpart which produce scratches and furrows on sliding track. Adhesive wear results when soft particle of polymer are caught and blocked among the asperities of counterpart, and it develops over a local area, being influenced by temperature rise. Fatigue and abrasive wear are responsible for the formation of the 3rd body between contacting parts which affects the friction and wear behavior. Morphological analysis of worn surface showed the rise of transfer film that induces instability of wear parameters.

Boehmite Nanofibers as a Dispersant for Nanotubes in an Aqueous Sol

2018 ◽  
Author(s):  
Gen Hayase
Keyword(s):  
Carbon Nanotubes ◽  
Aspect Ratio ◽  
Aqueous Solutions ◽  
High Aspect Ratio ◽  
Multiwall Carbon Nanotubes ◽  
Multiwall Carbon ◽  
Nanotube Films

By exploiting the dispersibility and rigidity of boehmite nanofibers (BNFs) with a high aspect ratio of 4 nm in diameter and several micrometers in length, multiwall-carbon nanotubes (MWCNTs) were successfully dispersed in aqueous solutions. In these sols, the MWCNTs were dispersed at a ratio of about 5–8% relative to BNFs. Self-standing BNF–nanotube films were also obtained by filtering these dispersions and showing their functionality. These films can be expected to be applied to sensing materials.

Sign in / Sign up

Export Citation Format

Share Document