Two-phase pressure drops in largediameter pipes

AIChE Journal ◽  
1957 ◽  
Vol 3 (3) ◽  
pp. 321-324 ◽  
Author(s):  
R. C. Reid ◽  
A. B. Reynolds ◽  
A. J. Diglio ◽  
I. Spiewak ◽  
D. H. Klipstein
Keyword(s):  
Two Phase ◽  
Pressure Drops ◽  
Phase Pressure

Prediction of Two-Phase Pressure Drop and Density Distribution From Mixing Length Theory

1963 ◽  
Vol 85 (2) ◽  
pp. 137-150 ◽  
Author(s):  
S. Levy
Keyword(s):  
Single Phase ◽  
Continuous Medium ◽  
Phase System ◽  
Mixing Length ◽  
Test Results ◽  
Two Phase ◽  
Pressure Drops ◽  
Mixing Length Theory ◽  
Phase Pressure ◽  
Good Agreement

Single-phase turbulent mixing length methods are used to predict two-phase flow. Two-phase density and velocity distributions and two-phase pressure drops are derived by treating the two-phase system as a continuous medium where the turbulent exchanges of momentum and density are equal. Good agreement is obtained between test results and analytical predictions.

Single- and Two-Phase Pressure Drops on a 6 × 6 Rod Bundle at 70 atm

1972 ◽  
Vol 15 (1) ◽  
pp. 25-35 ◽  
Author(s):  
P. Grillo ◽  
G. Mazzone
Keyword(s):  
Two Phase ◽  
Pressure Drops ◽  
Rod Bundle ◽  
Phase Pressure

High heat flux flow boiling in silicon multi-microchannels – Part III: Saturated critical heat flux of R236fa and two-phase pressure drops

2008 ◽  
Vol 51 (21-22) ◽  
pp. 5426-5442 ◽  
Author(s):  
Bruno Agostini ◽  
Rémi Revellin ◽  
John Richard Thome ◽  
Matteo Fabbri ◽  
Bruno Michel ◽  
...  
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Two Phase ◽  
Flux Flow ◽  
Pressure Drops ◽  
Phase Pressure

Two-Phase Pressure Drop of CO2 in Mini Tubes and Microchannels

2003 ◽  
Author(s):  
R. Yun ◽  
Y. Kim
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Large Diameter ◽  
Two Phase ◽  
Heating Method ◽  
Pressure Drops ◽  
Direct Heating ◽  
Frictional Pressure Drop ◽  
Phase Pressure

Two-phase pressure drops of CO2 are investigated in mini tubes with inner diameters of 2.0 and 0.98 mm and in microchannels with hydraulic diameters from 1.08 to 1.54 mm. For the mini tubes, the tests were conducted with a variation of mass flux from 500 to 3570 kg/m2s, heat flux from 7 to 48 kW/m2, while maintaining saturation temperatures at 0°C, 5°C and 10°C. For the microchannels, mass flux was varied from 100 to 400 kg/m2s, and heat flux was altered from 5 to 20 kW/m2. A direct heating method was used to provide heat into the refrigerants. The pressure drop of CO2 in mini tubes shows very similar trends with that in large diameter tubes. Although the microchannel has a small hydraulic diameter, two-phase effects on frictional pressure drop are significant. The Chisholm parameter of the Lockhart and Martinelli correlation is modified by considering diameter effects on the two-phase frictional multiplier.

Experimental Adiabatic Two-Phase Pressure Drops of R134a, R236fa and R245fa in Small Horizontal Circular Channels

2011 ◽  
Author(s):  
Chin L. Ong ◽  
John R. Thome
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
Prediction Methods ◽  
Two Phase ◽  
Pressure Drops ◽  
Wide Range ◽  
Small Channels ◽  
Experimental Pressure ◽  
Phase Pressure

Experimental adiabatic two-phase pressure drops data for refrigerants R134a, R236fa and R245fa during flow boiling in small channels with internal diameters of 1.03, 2.20 and 3.04 mm are presented. The main purpose was to investigate the effects of channel confinement on adiabatic two-phase pressure drops. Thus, the two-phase pressure drop trends were systematically investigated over a wide range of test conditions for all three refrigerants and channel sizes. Statistical comparisons have also been made by comparing the experimental pressure drop data database with various macroscale and microscale prediction methods from the literature. The comparison showed relatively moderate accuracy for three prediction methods developed for macroscale flows, i.e. Baroczy and Chisholm, Friedel and the homogeneous model with the Cicchitti et al. viscosity relation. As for microscale prediction methods, the Cioncolini et al. annular flow model worked best with 68.5% of the data within ± 30%, followed by the Sun and Mishima and the Zhang et al. methods. Combining this database with the LTCM lab’s earlier database for 0.509 and 0.790 mm channels, there appears to be no evidence of a macro-to-microscale transition, at least with respect to two-phase pressure drops.

Two Phase Pressure Drops for Refrigerants: A Statistical Comparison Among Experimental Data and Correlations

2006 ◽  
Author(s):  
Adriana Greco ◽  
Rita Mastrullo ◽  
Alfonso W. Mauro ◽  
Giuseppe P. Vanoli
Keyword(s):  
Experimental Data ◽  
Horizontal Tube ◽  
Operating Conditions ◽  
Prediction Methods ◽  
Two Phase Flows ◽  
Two Phase ◽  
Pressure Drops ◽  
Statistical Comparison ◽  
Wide Range ◽  
Phase Pressure

A 962 points database for refrigerants two-phase flows by Greco A. and Vanoli G.P. was statistically compared to four widely used prediction methods by Lockhart and Martinelli, Chawla, Theissing and Mu¨ller-Steinhagen and Heck in order to determine the best one. The experimental points are in a wide range of operating conditions for six pure or mixed refrigerants (R134a, R22, R407C, R507A, R410A and R404A) during evaporation in a smooth horizontal tube of 6 m length and 6 mm ID.

Void Fraction and Two-Phase Pressure Drops for Evaporating Flow over Horizontal Tube Bundles

2006 ◽  
Vol 27 (3) ◽  
pp. 5-21 ◽  
Author(s):  
Lorenzo Consolini ◽  
Douglas Robinson ◽  
John R. Thome
Keyword(s):  
Void Fraction ◽  
Horizontal Tube ◽  
Two Phase ◽  
Pressure Drops ◽  
Tube Bundles ◽  
Phase Pressure
Sign in / Sign up

Export Citation Format

Share Document