scholarly journals The Interesting Influence of Nanosprings on the Viscoelasticity of Elastomeric Polymer Materials: Simulation and Experiment

2012 ◽  
Vol 23 (9) ◽  
pp. 1156-1163 ◽  
Author(s):  
Jun Liu ◽  
Yong-Lai Lu ◽  
Ming Tian ◽  
Fen Li ◽  
Jianxiang Shen ◽  
...  
Keyword(s):  
Polymer Materials ◽  
Materials Simulation ◽  
Simulation And Experiment

scholarly journals Silicon Microdosimetry in Heterogeneous Materials: Simulation and Experiment

2006 ◽  
Vol 53 (6) ◽  
pp. 3738-3744 ◽  
Author(s):  
A. Wroe ◽  
A. Rosenfeld ◽  
I. Cornelius ◽  
D. Prokopovich ◽  
M. Reinhard ◽  
...  
Keyword(s):  
Heterogeneous Materials ◽  
Materials Simulation ◽  
Simulation And Experiment

Electron-diffraction studies in synthetic polymer materials

1983 ◽  
Vol 41 ◽  
pp. 362-365
Author(s):  
D.T. Grubb
Keyword(s):  
Electron Diffraction ◽  
Synthetic Polymer ◽  
Polymer Materials ◽  
Crystallographic Structure ◽  
High Dose ◽  
Electron Dose ◽  
Dose Rates ◽  
First Case ◽  
Diffraction Patterns ◽  
The Many

Diffraction studies in polymeric and other beam sensitive materials may bring to mind the many experiments where diffracted intensity has been used as a measure of the electron dose required to destroy fine structure in the TEM. But this paper is concerned with a range of cases where the diffraction pattern itself contains the important information.In the first case, electron diffraction from paraffins, degraded polyethylene and polyethylene single crystals, all the samples are highly ordered, and their crystallographic structure is well known. The diffraction patterns fade on irradiation and may also change considerably in a-spacing, increasing the unit cell volume on irradiation. The effect is large and continuous far C94H190 paraffin and for PE, while for shorter chains to C 28H58 the change is less, levelling off at high dose, Fig.l. It is also found that the change in a-spacing increases at higher dose rates and at higher irradiation temperatures.

Structure-property relationships of PE/PP sandwiched films

1987 ◽  
Vol 45 ◽  
pp. 454-455
Author(s):  
J. Petermann ◽  
G. Broza ◽  
U. Rieck ◽  
A. Jaballah ◽  
A. Kawaguchi
Keyword(s):  
Mechanical Tests ◽  
Polymer Materials ◽  
Ionic Crystals ◽  
Structure Property ◽  
Polymer Systems ◽  
Structure Property Relationships ◽  
Oriented Films ◽  
Materials Used ◽  
Polymer Laminates ◽  
Heated Glass

Oriented overgrowth of polymer materials onto ionic crystals is well known and recently it was demonstrated that this epitaxial crystallisation can also occur in polymer/polymer systems, under certain conditions. The morphologies and the resulting physical properties of such systems will be presented, especially the influence of epitaxial interfaces on the adhesion of polymer laminates and the mechanical properties of epitaxially crystallized sandwiched layers.Materials used were polyethylene, PE, Lupolen 6021 DX (HDPE) and 1810 D (LDPE) from BASF AG; polypropylene, PP, (PPN) provided by Höchst AG and polybutene-1, PB-1, Vestolen BT from Chemische Werke Hüls. Thin oriented films were prepared according to the method of Petermann and Gohil, by winding up two different polymer films from two separately heated glass-plates simultaneously with the help of a motor driven cylinder. One double layer was used for TEM investigations, while about 1000 sandwiched layers were taken for mechanical tests.

Electron spectroscopic imaging (ESI) on multiphase polymer materials

1989 ◽  
Vol 47 ◽  
pp. 348-349
Author(s):  
H.-J. Cantow ◽  
M. Kunz ◽  
M. Möller
Keyword(s):  
Energy Loss ◽  
Melt Spinning ◽  
Chromatic Aberration ◽  
Element Distribution ◽  
Polymer Materials ◽  
Specific Energy Loss ◽  
Transmission Electron ◽  
Multicomponent Polymer ◽  
Diffraction Patterns ◽  
Image Planes

In transmission electron microscopy the natural contrast of polymers is very low. Thus the contrast has to be enhanced by staining with heavy metals. The resolution is limited by the size of the staining particles and by the fact that electrons with different energy are focused in different image planes due to the chromatic aberration of the magnetic lenses. The integration of an electron energy loss spectrometer into the optical coloumn of a transmission electron microscope offers the possibility to use monoenergetic electrons and to select electrons with a certain energy for imaging. Thus contrast and resolution are enhanced. By imaging only electrons with an element specific energy loss the element distribution in the sample can be obtained. In addition, elastic bright field images and diffraction patterns yield excellent resolution. Some applications of the method on multicomponent polymer materials are discussed.Bulk polymer samples were prepared by ultramicrotoming at room temperature or well below the glass transition temperature. Very thin films for the direct observation of the structure in semicrystalline polymers were obtained by melt-spinning. Specimens were examined with a ZEISS CEM 902 operated at 80 kV.

Quantitative high-resolution electron microscopy (HREM) of defects in ordered polymers

1996 ◽  
Vol 54 ◽  
pp. 166-167
Author(s):  
Patricia M. Wilson ◽  
David C. Martin
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
High Resolution ◽  
Liquid Crystalline ◽  
High Resolution Electron Microscopy ◽  
Polymer Materials ◽  
Scattered Electron ◽  
Crystalline Polymers ◽  
Resolution Electron ◽  
Beam Damage

Efforts in our laboratory and elsewhere have established the utility of low dose high resolution electron microscopy (HREM) for imaging the microstructure of crystalline and liquid crystalline polymers. In a number of polymer systems, direct imaging of the lattice spacings by HREM has provided information about the size, shape, and relative orientation of ordered domains in these materials. However, because of the extent of disorder typical in many polymer microstructures, and because of the sensitivity of most polymer materials to electron beam damage, there have been few studies where the contrast observed in HREM images has been analyzed in a quantitative fashion.Here, we discuss two instances where quantitative information about HREM images has been used to provide new insight about the organization of crystalline polymers in the solid-state. In the first, we study the distortion of the polymer lattice planes near the core of an edge dislocation and compare these results to theories of dislocations in anisotropic and liquid crystalline solids. In the second, we investigate the variations in HREM contrast near the edge of wedge-shaped samples. The polymer used in this study was the diacetylene DCHD, which is stable to electron beam damage (Jc = 20 C/cm2) and highly crystalline. The instrument used in this work was a JEOL 4000 EX HRTEM with a beam blanidng device. More recently, the 4000 EX has been installed with instrumentation for dynamically recording scattered electron beam currents.

Determination parameters of 3D printing patriotic composite polymer materials based on ABS plasticse

2018 ◽  
Vol 4 (2) ◽  
pp. 85-90
Author(s):  
Y. M. Dovydenko ◽  
N. A. Ivanova ◽  
S. A. Chizhik ◽  
V. E. Agabekov
Keyword(s):  
3D Printing ◽  
Polymer Materials ◽  
Composite Polymer
Sign in / Sign up

Export Citation Format

Share Document