scholarly journals Amorphous Intergranular Films Enable the Creation of Bulk Nanocrystalline Cu–Zr with Full Density

2019 ◽  
Vol 21 (9) ◽  
pp. 1900333
Author(s):  
Olivia K. Donaldson ◽  
Timothy J. Rupert
Keyword(s):  
Full Density ◽  
Intergranular Films ◽  
The Creation ◽  
Bulk Nanocrystalline

The role of affect in feelings of obligation

2020 ◽  
Vol 43 ◽  
Author(s):  
Stefen Beeler-Duden ◽  
Meltem Yucel ◽  
Amrisha Vaish
Keyword(s):  
Positive Emotions ◽  
The Creation ◽  
Sense Of Obligation

Abstract Tomasello offers a compelling account of the emergence of humans’ sense of obligation. We suggest that more needs to be said about the role of affect in the creation of obligations. We also argue that positive emotions such as gratitude evolved to encourage individuals to fulfill cooperative obligations without the negative quality that Tomasello proposes is inherent in obligations.

Amorphous silica coating on α-alumina particles

1995 ◽  
Vol 53 ◽  
pp. 210-211
Author(s):  
J. W. Mellowes ◽  
C. M. Chun ◽  
I. A. Aksay
Keyword(s):  
Amorphous Silica ◽  
Heterogeneous Nucleation ◽  
Homogeneous Nucleation ◽  
Silica Coating ◽  
Full Density ◽  
Optimal Conditions ◽  
Fine Grained ◽  
Alumina Particles ◽  
Complete Mullitization ◽  
Powder Compacts

Mullite (3Al2O32SiO2) can be fabricated by transient viscous sintering using composite particles which consist of inner cores of a-alumina and outer coatings of amorphous silica. Powder compacts prepared with these particles are sintered to almost full density at relatively low temperatures (~1300°C) and converted to dense, fine-grained mullite at higher temperatures (>1500°C) by reaction between the alumina core and the silica coating. In order to achieve complete mullitization, optimal conditions for coating alumina particles with amorphous silica must be achieved. Formation of amorphous silica can occur in solution (homogeneous nucleation) or on the surface of alumina (heterogeneous nucleation) depending on the degree of supersaturation of the solvent in which the particles are immersed. Successful coating of silica on alumina occurs when heterogeneous nucleation is promoted and homogeneous nucleation is suppressed. Therefore, one key to successful coating is an understanding of the factors such as pH and concentration that control silica nucleation in aqueous solutions. In the current work, we use TEM to determine the optimal conditions of this processing.

Microstructural and fractographic characterization of B4C-Al cermets tested under dynamic and static loading

1989 ◽  
Vol 47 ◽  
pp. 562-563
Author(s):  
Gyeung Ho Kim ◽  
Mehmet Sarikaya ◽  
D. L. Milius ◽  
I. A. Aksay
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Static Loading ◽  
Carbon Deposition ◽  
Full Density ◽  
Unique Combination ◽  
Strong Component ◽  
Reaction Products

Cermets are designed to optimize the mechanical properties of ceramics (hard and strong component) and metals (ductile and tough component) into one system. However, the processing of such systems is a problem in obtaining fully dense composite without deleterious reaction products. In the lightweight (2.65 g/cc) B4C-Al cermet, many of the processing problems have been circumvented. It is now possible to process fully dense B4C-Al cermet with tailored microstructures and achieve unique combination of mechanical properties (fracture strength of over 600 MPa and fracture toughness of 12 MPa-m1/2). In this paper, microstructure and fractography of B4C-Al cermets, tested under dynamic and static loading conditions, are described.The cermet is prepared by infiltration of Al at 1150°C into partially sintered B4C compact under vacuum to full density. Fracture surface replicas were prepared by using cellulose acetate and thin-film carbon deposition. Samples were observed with a Philips 3000 at 100 kV.

Haydn: The Creation

1991 ◽  
Author(s):  
Nicholas Temperley
Keyword(s):  
The Creation
Sign in / Sign up

Export Citation Format

Share Document