A Constitutive Model and Processing Maps Describing the High-Temperature Deformation Behavior of Ti-17 Alloy in the β -Phase Field

2018 ◽  
Vol 21 (2) ◽  
pp. 1800775 ◽  
Author(s):  
Kenta Yamanaka ◽  
Hiroaki Matsumoto ◽  
Akihiko Chiba
Keyword(s):  
High Temperature ◽  
Constitutive Model ◽  
Phase Field ◽  
Deformation Behavior ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Processing Maps ◽  
Β Phase

Constitutive Analysis of the High-Temperature Deformation Behavior of Single Phase α-Ti and α+β Ti-6Al-4V Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 3607-3612 ◽  
Author(s):  
Jeoung Han Kim ◽  
Jong Taek Yeom ◽  
Nho Kwang Park ◽  
Chong Soo Lee
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Deformation Behavior ◽  
Single Phase ◽  
Volume Fraction ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Β Phase ◽  
Α Phase ◽  
Self Consistent

The high-temperature deformation behavior of the single-phase α (Ti-7.0Al-1.5V) and α + β (Ti-6Al-4V) alloy were determined and compared within the framework of self-consistent scheme at various temperature ranges. For this purpose, isothermal hot compression tests were conducted at temperatures between 650°C ~ 950°C to determine the effect of α/β phase volume fraction on average flow stress under hot-working condition. The flow behavior of α phase was estimated from the compression test results of single-phase α alloy whose chemical composition is close to that of α phase of Ti-6Al-4V alloy. On the other hand, the flow stress of β phase in Ti-6Al-4V was predicted by using self-consistent method. The flow stress of α phase was higher than that of β phase above 750°C, while the β phase revealed higher flow stress than α phase at 650°C. Also, at temperature above 750°C, the predicted strain rate of β phase was higher than that of α phase. It was found that the relative strength between α and β phase significantly varied with temperature.

High Temperature Deformation Behavior of Beta-Gamma TiAl Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 1531-1536 ◽  
Author(s):  
J.S. Kim ◽  
You Hwan Lee ◽  
Young Won Kim ◽  
Chong Soo Lee
Keyword(s):  
High Temperature ◽  
Deformation Behavior ◽  
Tial Alloy ◽  
Microstructural Analysis ◽  
Processing Condition ◽  
Simulation Method ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Β Phase ◽  
Dynamic Materials

In this study, high-temperature deformation behavior of newly developed beta-gamma TiAl alloys was investigated in the context of the dynamic-materials model (DMM). Processing maps representing the efficiency of power consumption for microstructure evolution were constructed utilizing the results of compression test at temperatures ranging from 1000oC to 1200oC and strain rates ranging from 10-4/s to 102/s and Artificial Neural Network simulation method. With the help of processing map and microstructural analysis, the optimum processing condition for the betagamma TiAl alloy was investigated. The role of β phase was also discussed in this study.

High temperature deformation behavior of Mg-5wt.%Y binary alloy: Constitutive analysis and processing maps

2020 ◽  
Vol 777 ◽  
pp. 139051 ◽  
Author(s):  
Nooruddin Ansari ◽  
Brian Tran ◽  
Warren J. Poole ◽  
Sudhanshu S. Singh ◽  
Hariharan Krishnaswamy ◽  
...  
Keyword(s):  
High Temperature ◽  
Binary Alloy ◽  
Deformation Behavior ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Processing Maps ◽  
Constitutive Analysis

A Multi-Scale Constitutive Model in High Temperature Deformation of Near Alpha Ti-5.6Al-4.8Sn-2.0Zr Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 1598-1601 ◽  
Author(s):  
Miao Quan Li ◽  
Jiao Luo
Keyword(s):  
Grain Size ◽  
High Temperature ◽  
Flow Stress ◽  
Constitutive Model ◽  
Deformation Behavior ◽  
Volume Fraction ◽  
Optimization Technique ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Multi Scale

Isothermal compression of near alpha Ti-5.6Al-4.8Sn-2.0Zr alloy is conducted on a Thermecmaster-Z simulator at the deformation temperatures ranging from 1173 K to 1333 K, the strain rates ranging from 0.001 s-1 to 10.0 s-1 at an interval of an order magnitude and the height reductions ranging from 50% to 70%. The primary grain size is measured at an OLYMPUS PMG3 microscope with the quantitative metallography SISC IAS V8.0 image analysis software. A multi-scale constitutive model coupling the grain size, volume fraction and dislocation density is established to represent the deformation behavior of near alpha Ti-5.6Al-4.8Sn-2.0Zr alloy in high temperature deformation, in which the flow stress is decomposed a thermal stress and an athermal stress. A Kock-Mecking model is adopted to describe the thermally activated stress, and an athermal stress model accounts for the working hardening and Hall-Petch effect. A genetic algorithm (GA)-based objective optimization technique is used for determining material constants in this study. The mean relative difference between the predicted and experimental flow stress is 5.98%, thus it can be concluded that the multi-scale constitutive model with high prediction precision can efficiently predict the deformation behavior of near alpha Ti-5.6Al-4.8Sn-2.0Zr alloy in high temperature deformation.

High Temperature Deformation Mechanism Maps of NiAl

2004 ◽  
Vol 449-452 ◽  
pp. 57-60
Author(s):  
I.G. Lee ◽  
A.K. Ghosh
Keyword(s):  
High Temperature ◽  
Strain Rate ◽  
Deformation Mechanism ◽  
Calculation Method ◽  
Deformation Behavior ◽  
Tensile Tests ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Grain Sizes ◽  
Temperature Strain

In order to analyze high temperature deformation behavior of NiAl alloys, deformation maps were constructed for stoichiometric NiAl materials with grain sizes of 4 and 200 µm. Relevant constitute equations and calculation method will be described in this paper. These maps are particularly useful in identifying the location of testing domains, such as creep and tensile tests, in relation to the stress-temperature-strain rate domains experienced by NiAl.

Sign in / Sign up

Export Citation Format

Share Document