Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by SLM

2015 ◽  
Vol 651-653 ◽  
pp. 677-682 ◽  
Author(s):  
Anatoliy Popovich ◽  
Vadim Sufiiarov ◽  
Evgenii Borisov ◽  
Igor Polozov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
Mechanical Behavior ◽  
Ductile Fracture ◽  
Elevated Temperatures ◽  
Initial Material ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Before And After

The article presents results of a study of phase composition and microstructure of initial material and samples obtained by selective laser melting of titanium-based alloy, as well as samples after heat treatment. The effect of heat treatment on microstructure and mechanical properties of specimens was shown. It was studied mechanical behavior of manufactured specimens before and after heat treatment at room and elevated temperatures as well. The heat treatment allows obtaining sufficient mechanical properties of material at room and elevated temperatures such as increase in ductility of material. The fractography of samples showed that they feature ductile fracture with brittle elements.

MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF AMORPHOUS Al–Cu–Ti METAL FOAMS SYNTHESIZED BY SPARK PLASMA SINTERING

2017 ◽  
Vol 24 (Supp02) ◽  
pp. 1850022
Author(s):  
MAOYUAN LI ◽  
LIN LU ◽  
ZHEN DAI ◽  
YIQIANG HONG ◽  
WEIWEI CHEN ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Elevated Temperatures ◽  
Volume Fraction ◽  
Metal Foams ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Xrd Patterns

Amorphous Al–Cu–Ti metal foams were prepared by spark plasma sintering (SPS) process with the diameter of 10[Formula: see text]mm. The SPS process was conducted at the pressure of 200 and 300[Formula: see text]MPa with the temperature of 653–723[Formula: see text]K, respectively. NaCl was used as the space-holder, forming almost separated pores with the porosity of 65 vol%. The microstructure and mechanical behavior of the amorphous Al–Cu–Ti metal foams were systematically investigated. The results show that the crystallinity increased at elevated temperatures. The effect of pressure and holding time on the crystallization was almost negligible. The intermetallic compounds, i.e. Al–Ti, Al–Cu and Al–Cu–Ti were identified from X-ray diffraction (XRD) patterns. It was found that weak adhesion and brittle intermetallic compounds reduced the mechanical properties, while lower volume fraction and smaller size of NaCl powders improved the mechanical properties.

Mechanical behavior of SiC at elevated temperatures

1985 ◽  
Vol 71 ◽  
pp. 209
Author(s):  
E.R. Fuller ◽  
S.M. Wiederhorn ◽  
N.J. Tighe ◽  
L. Chuck
Keyword(s):  
Mechanical Behavior ◽  
Elevated Temperatures

scholarly journals 326 Mechanical Behavior of Experimental Oxidation and Sulfidation Resistant Alloys at Elevated Temperatures

2002 ◽  
Vol 10.1 (0) ◽  
pp. 608-613
Author(s):  
K. K. Schrems ◽  
J. S. Dunning ◽  
D. E. Alman ◽  
J. A. Hawk ◽  
O. N. Dogan
Keyword(s):  
Mechanical Behavior ◽  
Elevated Temperatures

Mechanical behavior and related microstructural aspects of a nano-lamellar TiAl alloy at elevated temperatures

2017 ◽  
Vol 128 ◽  
pp. 440-450 ◽  
Author(s):  
T. Klein ◽  
L. Usategui ◽  
B. Rashkova ◽  
M.L. Nó ◽  
J. San Juan ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Tial Alloy ◽  
Elevated Temperatures

Mechanical Behavior of 2D C/SiC Composites at Elevated Temperatures under Uniaxial Compression

2011 ◽  
Vol 462-463 ◽  
pp. 1-6 ◽  
Author(s):  
Tao Suo ◽  
Yu Long Li ◽  
Ming Shuang Liu
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Carbon Fiber ◽  
Mechanical Behavior ◽  
Uniaxial Compression ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Carbon Matrix ◽  
Structural Applications ◽  
Sic Composites

As Carbon-fiber-reinforced SiC-matrix (C/SiC) composites are widely used in high-temperature structural applications, its mechanical behavior at high temperature is important for the reliability of structures. In this paper, mechanical behavior of a kind of 2D C/SiC composite was investigated at temperatures ranging from room temperature (20C) to 600C under quasi-static and dynamic uniaxial compression. The results show the composite has excellent high temperature mechanical properties at the tested temperature range. Catastrophic brittle failure is not observed for the specimens tested at different strain rates. The compressive strength of the composite deceases only 10% at 600C if compared with that at room temperature. It is proposed that the decrease of compressive strength of the 2D C/SiC composite at high temperature is influenced mainly by release of thermal residual stresses in the reinforced carbon fiber and silicon carbon matrix and oxidation of the composite in high temperature atmosphere.

Sign in / Sign up

Export Citation Format

Share Document